Liczymy pasujące modele…
This is a Remix of the Aurora handle and spool holder for Kingroon KP3S Pro and S1. This version can mount spools of maximum 85cm depth, and can be mounted to have the spool both on top of the printer and left-rear side to use the…
This remix for Artiller Sidewinder X4 Pro/Plus permit to mount the TZ Bambu clone hotend. You can use v2.0, v3.0, v4.0. Also Bambu original, Obxidian, Chimera, Phaetus, Biqu Panda Revo, Microswiss and every hotend for Bambu P1/X1 printers…
Tired of the original spool holder that causes the extruder to struggle by pulling the filament? Here is the Filler for Sidewinder X4. It uses 2 skateboard wheel bearings and has no friction. Available 2 supports for left and right side,…
For TwoTrees SK1 a modified extruder cover to avoid TPU jamming. Also the spring is too long, cut 2mm or change with a new one 6 mm outher diameter, 10 mm long and 0.7 mm wire diameter or 0.6 for softer feedback (needs to be screewed more…
An inexpensive full upgrade of the hotend with less than $20 total cost for Kingroon KP3S 3.0, Pro and S1. It's based on TZ Bambu clone hotend with V6 adapter and BMG clone dual gear extruder, but stock Titan can be used. Remember the BMG…
After some fine tuning putting the T8 screws most vertical as possible I discovered that the upper sync belt is loose. I designed this simple belt tensioners to use with a couple of idler pulleys. 2x 16T without teeth GT2 6mm idler…
In this remix the shroud is more easy to print and more open in the down side for easy inspection of the probe and hot end. Easy to remove cover without remove the PTFE tube or top cable.
Here an inexpensive E3D V6 clone with Titan extruder in configuration Direct Drive mounted on an Ender 3 V2 Neo. Let's start from important notes: to have the pancake stepper work on the Ender 3 V2 Neo the central wires of the stepper…
Cable chain management for Artillery X4 Plus. This is a remix of something found around not on Printables. This version has stronger parts so they need a longer M3 screews to lock on toolhead and leadscrew coupler support. For X4 Plus you…
A conversion from 2x 4020 cooling fan to 1x 8010 fan over the mainboard to cool stepper drivers and host CPU heatsink. To do this mod you have to change the stock heatsinks of the TMC2209 drivers with low profile type, better use copper…
9mm GT2 Y belt for Artillery Sidewinder X4 Plus It has reported the stock Y axis 6mm GT2 belt is weak. Here a mod to convert to a 9mm GT2 belt. Parts needed: 2m of GT2 9mm belt aramidic or glass or kevlar fiber (don't use steel wire…
Artillery Sidewinder X4 Pro and Plus hotend fan shroud. A minimalistic version with some improvements. On original design the duct has very thin walls and is difficult to print, lot of materials leave holes in duct walls. This has thinner…
CYD ESP32-2432S028R 2.8" display for Klipper Here project's site: https://github.com/suchmememanyskill/CYD-Klipper Built a support for the TwoTrees SK1 display. Modified the box to use the JST 1.25 4way plug provided with the screen. It's…
On Artillery Sidewinder X4 Pro/Plus a weak point is the hotend ribbon cable, it touches the gantry bars and can damage. This project is for relocating this cable in front. The lower part can be chained or left free. The upper part is too…
A simple tool I've designed to align gantry of my bed slingers. Used for Ender 3, Artillery Sidewinder X4 Plus and so on. Print two pieces.
Enclosure for the SBC Sipeed Longan Pi 3H Hardware needed: 4x M2.5 x 5 or 7mm
Enclosure for CYD Klipper 3.2" capacitive version for TwoTrees SK1. The support is for SK1 but you can use the enclosure for other model of printers.
An enclosure and support for the CYD Klipper to mount on Artillery Sidewinder X4 Plus. It's possible to take power 5V and GND from the JST X2.54 used for stock screen, unplug the RJ9 for the screen and build a plug to power the CYD. Plug…
If you build your own Klipper firmware using Armbian for MKS SKIPR Mini the screen doesn't work anymore. The screen software KlipperLCD from Tortillery firmware for Artillery Sidewinder X4 Pro/Plus works very well also on SK1 but the…
Artillery Sidewinder X4 Pro/Plus has a custom version of the Makerbase SKIPR Mini that has not strong protections from short circuit, expecially if you work on tool head with printer switched on. If a short occurs often only the MCU part…
To wszystkie aktualnie dostępne wyniki.
