Liczymy pasujące modele…
Alternative shell model for the Framework Laptop expansion cards. I didn't like the official expansion card 3D model as it prints vertically, isn't fully enclosed, and didn't fit very securely in the expansion slots. So I made my own. Two…
Meticulously modeled 40° stand for the Logitech MX Ergo trackball mouse. Includes a slot for a trackball pusher tool (included) as well as a storage slot for the USB wireless receiver. Uses (4) 9.5mm x 2.5mm and (8) 6mm x 3mm neodymium…
Simple NPT M-M 1/2inch adapter that I use to extend a standard shower hose. 12mm ID, thread length of 10/15mm for use with/without a rubber washer. Disclaimer: threads are not tapered so not true NPT. Works well enough though from my…
My take on a single shot adapter for the 22LR CZ457. The main difference between this and other single shot adapter designs is the integrated spring on the front that lifts the bullet such that it enters the barrel chamber without…
Flexible 2.5in (63.5mm ID) segmented/modular hose system designed in such a way that all parts can be printed in vase mode for faster prints and to ensure a good seal between each component. The hose is capable of 90° bends with 6…
Simple low profile stand for the 11th generation (2021) Kindle Paperwhite. Might work with earlier models, but YMMV. STLs are provided that hold the device at 60°, 65°, 70°, 75°, and 80°. Original design file is parametric as well for…
Wind vane attachment for WeatherFlow's WEATHERmeter . A single 608 bearing (22mm x 8mm x 7mm) required for assembly. Base has standard ¼-20 threading for tripod mount. There are two base models, one where the top peg (that goes into the…
Mounting rail/arm for the Garmin Xero C1 chronograph. Comes in three lengths (3", 4", 5") with either the 17S footprint (for use with Area419 ARCALOCK clamps ) or a generic footprint that should work with Amazon sourced clamps (eg.…
Miniature low-profile belt/strap buckle that is only 0.42g and 2mm thick. Provided model is designed for 10mm x 1mm straps but the original design file is parametric for relatively easy modification. Not intended for load bearing…
Basic picatinny/weaver one piece scope rings for 1in, 30mm, and 34mm tubes. Height options range from 16mm to 38mm as measured from top of rail to center of ring in 1mm increments. Available in text and no-text versions. One 25mm M3 bolt…
A simple dock/charging stand for the Apple Watch and AirPod Pro that I spent far too much time on to model G2 (continuous curvature) surfaces across the outer shell. Can be printed without supports and has very tight tolerances Designed…
Adapter to bridge a standard 5in or 5.9in counter-clockwise portable air conditioner hose to a Honeywell AC unit. Tested on model HF0CESVWK6 but may work for similar units. Note that this is specifically targeted to fit these Honeywell…
Simple low profile filament clip for Prusament filament rolls. Locks filament into place without shifting unlike screw or clip on variations. Inspired by Pavel's version ( https://www.prusaprinters.org/prints/12942-prusament-clip ) but…
Compact stand for 9th and 10th gen (7" screen) Kindle Oasis. Supports both left and right hand vertical orientation. Very snug fit. Models for angle orientations from 60-85° provided. I personally find that 70° is optimal but YMMV. The…
This is a modification of my previous compact phone stand model that targets the iPhone 13 series. As usual, the original design file is fully parametric for easy adjustments. STLs are included for all iPhone 13 variations. Note that I…
Frame braces to stiffen Z axis frame. Intended for printers with the PSU and Einsy board removed for operation in a heated enclosure. Einsy brace uses 4 M3 screws while the PSU brace uses 2 M3 and 2 M4 screws. Prints without supports.…
Desiccant holder that mounts to any 120mm fan using the standard self-tapping mounting screws that comes with the fans. Designed such that the drawer can be printed out of high temperature filament (Colorfabb HT/PC) so that the entire…
Simple low profile stand for the Kobo Clara BW and Clara Color. STLs are provided that hold the device at 60°, 65°, 70°, 75°, and 80°. Original design file is parametric as well for easy modification.
Alternative adapter for mounting TriangleLab's Dragon hotend to the Bondtech's MK3S extruder upgrade . Enables single handed nozzle removal as the adapter will prevent the hotend from rotating, unlike the stock one. Design uses two…
Belt holder for standard box of 25 count 12 gauge shells with slots for spares. Prints without supports. Should be printed with a minimum of two perimeters, preferably three.
Modified version of my compact vertical/horizontal stand for the iPhone 15 series of phones. As usual, the original design file is fully parametric for easy adjustments. STLs are included for all iPhone 15 variations. Note that I have…
This is a novel design for a printable joystick bipod that utilizes compliant mechanisms (flextures) for movement control. Design The mechanical design of the flexture allows for fine grain control of vertical and horizontal movement via…
Result of some exploration around improving print quality via high volume but slow(er) airflow. Rear fan mount collides with frame, so the Z-axis mount needs to be replaced. Z_MAX_POS also needs to be reduced via firmware modifications or…
Custom designed bag hanger for closet rods with a diameter of 1.25 inches (32mm). Prints without supports or bridges, with a max overhang of 55 degrees. Max weight depends on what material used for the print, but the design is intended to…
To wszystkie aktualnie dostępne wyniki.
