Nissan 200sx shift boot holder
The lower bracket that holds the control lever. it fits but not properly. it's just a prototype
Wydruk około 2,64 €–3,23 € nettoWstępna wycena dla PETGMateriał u źródła: PET
- Pobrania
- 249
- Polubienia
- 27
- Ocena
- 5
67 modeli
The lower bracket that holds the control lever. it fits but not properly. it's just a prototype
Wydruk około 2,64 €–3,23 € nettoWstępna wycena dla PETGMateriał u źródła: PET
small clip on the sides of the trunk
Wydruk około 0,55 €–0,67 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This mounting bracket allows to fit the ZWO ASI EAF focusing motor to a Vixen R200SS optical tube assembly.
Wydruk około 1,45 €–1,78 € nettoWstępna wycena jednego wariantu
A simple gauge pod for the Nissan S13 that mounts below the dash. It replaces the oem vent assembly. fits 52mm gauges and 60mm gauges My design is a straight replacement of the oem vent assembly. no cutting, no drilling, 100% reversible.…
a radiator support bracket, fits Nissan S13 / 180SX / 200SX / 240SX probably also other 90s Nissans
a full set of fuel line holders to replace the rusty and brittle oem clips on your 180sx/200sx/240sx Nissan S13 4 Versions: oem replacement oem replacement but without the evap / fuel tank venting line Version with additional brake line…
I had them uploaded on Shapeway's website because it was the only website for sharing 3D prints back then, and had them for FREE download..it seems they removed this option now and because i get a lot of messages through the years i am…
another wiper pivot replacement design. two piece for prints without support.
Mounting Base Counterplate and Clamp uses M8 allthread with a welded tab added Versions without Nissan and 200SX Features
Did you remove your fuse box from the engine bay and are now realizing that the oem coolant reservoir was mounted to that fuse box? Here is your solution!
A replacement hard disk drive cover for X200-series Thinkpad laptops (X200 X200s X201 X201s). No raft or support needed, the horizontal notch might need a little bit of cleanup after print to properly fit. Category: Parts
Wiring grommet for right side of the S13 with bigger hole to fit 50mm2 battery wiring, print with some flexible filament like TPU or TPE.
V2. Printed and test fit and working well.
I needed a bracket to mount my ZWO EAF to my Vixen R200SS telescope's focuser. Modelled and printed this in CF-PETG, I'd recommend a CF-fill filament for stiffness reasons as regular PETG was quite bendy. Needs 4x M3 screws and washers to…
I was handed a metal thingy and told it needed a transport sleeve. I think it's for a bolt action lever? If that's even a thing? I printed it standing and it came out great. Use supports for the overhang.
Allows the mounting of picatinny accessories to the top slide of the ZWQ S200s Viper. Uses 4x M3 screws. You probably want some coarse thread countersunk ones for the longevity of the holes in the plastic slide, but I ended up using…
If you have S13 and the measured diameter what is shown on the picture is 57-57,4mm, this cap fits for you. I am printed it with ABS and heated the link between the cap and holder ring, to fold it together, but PETG works also I think.…
I needed an air filter for the bus I live in and it needed to be able to mount to the wall out of the way. The clips on this design make it robust when assembled but easily disassembled when its time to replace the filter. Electronics I…
TPU stabilizer silentblock for Nissan 200sx S13. 100% infill 6 perimeters wall
Remix of FredRaket's Pioneer speakers wall mount for Samsung SWA-9200S speakers or any speaker with keyhole mount
Profesional scanned high resolution nissan 200sx s13/ 180sx Rear end interior. Category: Automotive
Original the air of this purifier would come out on top, blowing straight up. I wanted it to blow forward to create a better air circulation. This air deflector is being installed by simply pushing it into the vent cover.
Corner and furniture bracket for rear speakers SWA-9200S of Samsung soundbar and others. Any filament can be used, minimum 3 perimeters, 20% fill. Requires 2 screws for installation, one additional screw into the speaker hanging hole,…
This is a ring pull for the ZWQ Viper S200s that mounts to the top of the slide using four M3 bolts. There is a version for countersink bolts and normal cap head bolts. The ring pull sits low enough to not obscure the sights, but is still…
This tray is intended to catch water drops and ice chunks after dispensing on the Samsung fridge RS22T5200S9 (and similar models).
Professional 3d high resolution Scanned Nissan 200sx s13/ 180sx Engine Bay Category: Automotive
TPU silentblock for stabilizer bars. 100% infill 6 perimeters walls
The lower sleeve which is attached to the ignition lock with two screws.
Gasket under the throttle and on the other side of the intake Engine: CA18DET Printed with FLEXfilament
thermostat gasket Engine: CA18DET Printed with FLEX filament
This is an Atoto S8 radio bezel I designed for a Nisan B14 to fill the gaps in the dash around the unit. It will fit a Atoto S8 Standard 7" radio in the factory center console of a Nissan B14 200SX/Sentra chassis, year 1995-1999. However…
Gridfinity bin for USB C200S Iron and accesories.
a small clip into the electrical connector so that it can be attached with cable ties
If you have a ZWQ s200s viper blaster that you have upgraded, chances are, it is difficult to adequately grip the smooth slide. In my particular blaster, I have installed a K25 spring, which makes it difficult to prime with its current…
Printed with FLEX filament
Positive batery box for Nissan 200 sx s13. When i relocate battery to trunk i needed little box for the cable. At one side is M8 screw and going through fender. and on the other side is M6 screw. All screw been install with little bit of…
My boats fuel tank sender gasket was deteriorated pretty bad. This was a quick, easy print @ 50% infill using Overture high speed TPU. Its been working great so far.
modèle détailler d'une moto Kawasaki zrx1200s
This little modification is needed for aspirator hose connect to your heater box to proper work of interior temp sensor. This is the scond version. I am designed only the bottom part of adapter. So you need the JDM part and cut down like…
Replacement cover for Furlex 200S furler. Press fit 1/4-in nylon lock nuts on the inside.
This could be a replacement casing where one has been lost or broken. It's for the Levoit Smart HEPA Air Purifier 200S specifically. I managed to buy a Levoit 200S from Ebay, because the owner had lost the bottom part of the unit which…
Shopping cart fixture for Samsung vehicle dock EE-V200SA. On the bottom it has insert in the same size as 1 EURO coin. It allows to unlock any shopping cart with open, horizontal coin socket. Simultaneously it allows to attach whole…
it is a relatively short print and is an easy print, it allows you to put essential oils on a cotton pad then in the holder grid to allow air to pass over and through it to improve air quality and smell without chemicals as a Febreze…
I didn’t have a button on the center console next to the steering wheel, and I didn’t actually need a functional button — I just needed something to cover the opening. So I made a button that fits Plug & Play into the original spot. It…
This is a custom-designed holder for the Philips 3200 Series coffee machine. The holder is designed to take advantage of the structural features of the machine. It slots into the side vent holes using two pins for positioning and is…
RD8200SG Comes with the flimsiest and uninspired phone mount for having your phone attached with your locator. I designed this from scratch and it's my first version. Printed with PLA Gyroid 60% infill and it's very sturdy. The ball joint…
Мijiа Мi Rоbоt Vасuum Сlеаnеr (SКV4000GL, SКV4000СN, SКV4022GL, SDJQR01RR, SDJQR02RR, SDJQR03RR) Мijiа Мi Rоbоt Vасuum Сlеаnеr 1S (SКV4054СN) Rоbоrосk Swеер Оnе S5 s50/s51/s55 (S502-00, S502-02, S512-00, S512-02, S522-00, S522-02,…
Print with the front of the plate facing the print bed. Supports required for the two latches (for the bottom side of the DIN mount), though you can modify the provided Fusion 3D/STEP file to round/chamfer this off to print without…
Replaces center air vents for 3x 52mm gauges. reccomended to block AC hoses for center panel.
4" duct collar on an ~8" curved base designed to roughly fit the Levoit Core 200S-P Air Purifier. This was designed with the intention to fit two or more collars on the air purifier to make branch lines that can connect to multiple zones…
I wanted my viper to be a bit more powerful, but not as powerful as the upgrade spring, so I made some spacers to fit the viper. I don't know how much more power it gives, but it seems more powerful. It seems that 27.5mm is the absolute…
a simple replacement for the tail light bracket might work for other bikes
Replacement buttons for the Perodua Kancil (K1-K3)/Daihatsu Mira (L2S/L200S) dashboard clock. Prints without supports.
Designed by Samuel Meppen, Nassau Computer Repairs LLC. Designed for use with the Levoit Core 200S-P Air Purifier: https://levoit.com/products/core-200s-p-smart-air-purifier Allows a 8" HVAC Piece to fit the top of the air purifier. To…
I wanted to have a side charging handle for my viper, but there weren't files for it already, so i designed one in tinkercad in an hour Actual charging handle piece made by narangdlover from here: SMC-9 custom charging handle assy by…
NiSi Macro Rail Precision Dial & Reference Indicator While some NiSi macro focusing rails (such as the NM-200S) come equipped with an integrated indexing dial, many versions feature a plain oblong adjustment knob with no reference…
Fan Guard for Phanteks PH-F200SP with hole spacing 154mm. Made with Gemini, tested on actual fan. Printed in PETG.
Southwire Strip-All SA-200SK Gridfinity bin. 2x4.
A replacement rear housing for the Perodua Kancil (K1-K3)/Daihatsu Mira (L2S/L200S) dashboard clock with faithful and easier-to-print versions. The faithful version requires extensive supports and preserves the look of the side that you…
Purifier made from 4 or 6 140mm PC fans with Levoit Vital 200S filters. In my case, i used P14 ARCTIC fans, with ESP32 to change RPM. (MQTT with FUXA dashboard in my case). If you want to use only 4 fans, you can tape some cardboard over…
This tray is intended to catch water drops and ice chunks after dispensing on the Samsung fridge RS22T5200S9 (and similar models).
This could be a replacement casing where one has been lost or broken. It's for the Levoit Smart HEPA Air Purifier 200S specifically. I managed to buy a Levoit 200S from Ebay, because the owner had lost the bottom part of the unit which…
a radiator support bracket, fits Nissan S13 / 180SX / 200SX / 240SX probably also other 90s Nissans
4" duct collar on an ~8" curved base designed to roughly fit the Levoit Core 200S-P Air Purifier. This was designed with the intention to fit two or more collars on the air purifier to make branch lines that can connect to multiple zones…
The idea for this design was suggested by MadMopar (over on MakerWorld), since he wanted to use the " Perfect Poor Man's Filter " by MrFunctionalPrint (also over on MW), but it would not fit on a P1 without using a split model. I really…