35 modeli
A holder to attach a DIN rail to the back of a FritzBox 7583. The 7583 has a very odd shape with a big cutout in the back, making it protrude quite far from the wall. To reclaim this lost space and to better organize my Raspberry Pi…
Wydruk około 0,20 €–0,24 € nettoWstępna wycena jednego wariantu
This model is compatible with the lego system.
This model is compatible with the lego system.
keebcu - andimoto7583 mechanical keyboard This is one of my keyboard designs I made with my keebcu keyboard customizer. It is a 75% mechanical keyboard which can be printed on smaller printers such as Prusa Mini. If you want to build the…
This model is compatible with the lego system.
Allis-Chalmers 7580 4WD - 1:16th Scale Uses M4 and M2 screws
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
2026-11-02 update. STEP file uploaded. Minor improvements made to thickness of the catches so that they fit better, and also the thickness has been increased slightly to make it more durable. Strap radiuses increased to make it more…
The design is meant to be used with M6 screws from the rack. It was originally printed in PLA, which turned out to be stronger than the original material. Update : The PLA did not withstand the stress, and I encountered difficulties…
This model is compatible with the lego system.
These trim pieces are easy to break when removing the center taillight piece. The original pieces are aluminum with steel mounting studs. They included models are: 75833-14030 - Left side (#2 in the diagram) 75832-14060 - Right side (#2…
This model is compatible with the lego system.
As I have not found anything comparable, here is a model that allows two additional 3.5” hard disks to be mounted in a Fujitsu P759 P758 P959 P958 and similar. Apart from the mounting of the hard disks in the bays, the model is completely…
Disclaimer: The functionality depends a lot on your individual print settings & maerial choice. So make sure to test this replacement part from time to time to ensure its functionality! (more about that later in the describtion) I'm only…
Jaguar XK8 XKR Airbag Badge GJE4758AA Blank Airbag Seat Plate for a 2003+ Jaguar X100. Original Part is NLA. I did not put the lettering on as it never printed well on the small piece. Category: Automotive
I took the mount from the Porsche 963 76916 and remade it. The base was too big for the senna as the tires and wheels it the base and it would not sit fully down. I also wanted the prongs on the mount to be centered rather than offset. It…
If you find my designs useful, please consider sending a tip The original jaws broke on my Meade LX200GPS's autostar holder long ago (Meade part no 07580), and were since lost. I found a half of one of the original jaws when clearing out…
This is a replacement for the volume knob of a NAD receiver (specifically T758 (or T748). I made it since the original version was too deep that it was in the way of the tv bench doors. In other words, this is a simplified variant that is…
I made a replacement screwhole for the A 208 758 0438, because mine snapped. This little guy goes right into the broken hole. I do recommend you print with PETG or any other durable material with 100% infill. PLA works fine but most…
When printing materials such as polycarbonate, it’s strongly recommended to run a heated enclosure to minimize warping and improve layer adhesion. I wanted to build the excellent “Prusa Enclosure Heater and Temperature Controller” setup…
Technic Compatible Panel Car Mudguard Arched 13 x 2 x 5, Arched Top, Pointed Bottom (6593758 | 80284)
Es ist ein Ersatzteil für die Aufhängung für den Auzug des oberen Korbes. Wenn sie das ander von der anderen Seite brauchen spiegeln sie es in ihrem Slicer einfach. Denken sie bitte daran dass es nicht klug ist es aus PLA zu drucken. Ich…
Two SEZ 7580-08 connected by using M8 screw with nut to connect 25mm2 cables.
87580 (Plate, Modified 2 x 2 with 1 Stud on Top) Lego piece about 2 grams
Bloomberg Dishwasher 175883 Start Button Replacement, this gets glued onto the clear display case. This only replaces the start button, slight modification to the model would be required for the other buttons. The case is made of PP, so…
📜 Entry from the Artifact Forge. Object B-9758 found in the techno-relic sector. Purpose unknown... 🔖 Artifact name: Artifact B-9758: House for MR83ZZ 🧾 About the artifact: Chaos has broken out in the workshop: small MR83ZZ bearings (8×3…
Rear French Military Light (reverse light and fog light) - Gabriel Lyon 67580 at 1:1 scale already simplified
This allows you to rebuild your charcoal canister and make it future serviceable at the same time. Sand ~1/16" off the bottom of the canister, tap around the edge to break the bond and remove the old bottom. Use epoxy to install the…
Allis-Chalmers 7580 4WD - 1:16th Scale Uses M4 and M2 screws
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
https://www.patreon.com/posts/50624838
