Liczymy pasujące modele…
I have lost some of the condensation hole covers in the window frames through age and also the sun. The windows are from Finstral. It might fit other frames as well. With this cap it is possible to cover a hole of max 30mm in length and…
Wydruk około 0,12 €–0,15 € nettoWstępna wycena jednego wariantu
Captures condensate in air conditioning.
Wydruk około 35,04 €–42,82 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a part that connects to the lower part of the air conditioner and to it the hose for draining condensate. Because the shape is funnel, there is no need for a rubber seal. The diameter of the hole in the air conditioner is approx.…
This is a holder for the Midea PortaSplit. It can hold serilisation and cleaning tablets for AC condensate. This may help prevent the P1 error which is caused by clogging of the condensate pumps filter. Regularly check on the state of the…
Earlier manuals recommend cleaning the condensate tray with AC cleaning tabs. However the PortaSplit doesn't really come with an ideal location to put these tabs - one might be able to squeeze them in behind the plastic to the left and…
This adapter lets you connect your Ridgid shop vac directly to your AC condensate drain line to suck out clogs in seconds. The Problem: AC condensate drain lines clog frequently with algae and debris, causing water to back up and…
JeNo 3" Support condensateur. Se place sur les entretoises verticales avant. Imprimer “ring” une fois et “bottom” deux fois. Le tout en TPU, sans support.
This model is for the DeLonghi Magnifica S I suggest PETG for this model.
This is a drain for the Truma condensation water to prevent the formation of icicles. I printed this using TPU with default settings. No supports required. Extra tip: rotate the top solid infill direction so that the lines point in the…
When your gas heater is running, water condenses on the Truma wall chimney and runs down the outside of the caravan or camper. Over time this leaves dirty streaks and water marks below the chimney. This drip edge fits onto the Truma WK 24…
Einfacher zweiteiliger Untersetzer, der das Schwitzwasser in der unteren Hälfte auffängt, hier kann es nach entnahme des Einsatzes einfach entsorgt werden. Simple two-piece coaster that collects the condensation in the lower half, here it…
WARNING, Your print must be waterproof!
See the story on: https://speleobrad.github.io/compressor/compressor-drainer/ Parametric vortex water separator for PET bottles. Built in OpenSCAD, has configurable number of inlet hoses, their diameter and bunch of other stuff. Prints…
A simple, sturdy straight connector for joining two hoses of the same size. The two ends are barbed spigots that push into the hose ; a central collar acts as a hard stop so both hoses seat to the same depth. Typical uses: Condensate…
🚐 Truma Condensation Drain Pro – Ultra-Rugged & Anti-Stain Tired of those annoying black streaks on your camper’s side? Or even worse, tired of flimsy 3D-printed drains that snap off during the first wash? This Pro version has been…
If you have a ½ vinyl hose emptying into your basement slop sink and you want to secure it, slip this hose holder over the edge of you sink. Sink edge should not exceed ⅓ inch and vinyl hose size should have an outside diameter of ½ inch…
After a few years in operation, my Vaillant EcoLevel condensate pump broke down (no more pumping function). The sensor system for the pump control is based on Hall elements. A float with integrated magnets moves up and down on a guide rod…
I needed to vacuum out my AC unit's condensation line, and was going to try the adapter from @MikeLugo177399, but my line doesn't have a fitting on the end, just a 3/4" PVC pipe. This simple adapter just lets the hose slip over one end…
Modified AC condensate drain to incorporate a 13mm ID LDPE barb fitting
This model is ugly but functional. Fortunately, I shouldn't have to look at it more often than once every 6 months. This 3d printed frame combines: peristaltic pump xiao ESP microcontroller L298N motor driver 9v rechargeable battery This…
USE AT YOUR OWN RISK The condensate drain trap for my Lennox furnace was cracked and leaking. The replacement part was too expensive, so I made this model to print. It seems to be working for me, but I have NO GUARANTEE that it will work…
This is a replacement screw cap for the Baxi Gas Boiler. The condensate trap has a screw that you can unscrew if you want to flush and clean it. The original one had formed a crack and was leaking condensate water. After measuring the…
A flood in our storage room/Heater-AC closet made a mess and me realize that I needed to make a monitor. I already have a Home Assistant Server in service for my 3D printer so I am using it along with the ESPHome integration to monitor…
Inner dimensions: 92mm x 222mm
AC Condensate Drain Fitting (Straight & 90° Elbow) A snap-in drain outlet for the condensate hole in an air-conditioner or outdoor-unit tray. Push it into the hole and the reinforced clips lock behind the sheet metal (about 1.3,1.4,1.5 mm…
Our upstairs AC had nowhere to drain its condensate — no central drain line, and we rent, so no permanent plumbing. Meanwhile a neighbor made a hobby of walking along the building and collecting every AC drip on her head. Out of a dozen…
AC Condensate Drain Fitting (Straight & 90° Elbow) A snap-in drain outlet for the condensate hole in an air-conditioner or outdoor-unit tray. Push it into the hole and the reinforced clips lock behind the sheet metal (about 1.3,1.4,1.5 mm…
Replacement condensate cup for Aroma 4-cup rice cooker. Mine is a slightly older version, so I couldn't find a replacement for this one specific part. PETG recommended for this part, I tried a PLA version but it warped with the heat of…
This model is for the DeLonghi Magnifica S I suggest PETG for this model.
🚐 Truma Condensation Drain Pro – Ultra-Rugged & Anti-Stain Tired of those annoying black streaks on your camper’s side? Or even worse, tired of flimsy 3D-printed drains that snap off during the first wash? This Pro version has been…
