1151 modeli
I found this focus wheel at https://www.thingiverse.com/thing:714475 , but it was 11.1mm thick and it made my camera look like a toy so I created a much slimmer one. My final design comes in at 4.4mm so it is much more compact and works…
Wydruk około 0,73 €–0,89 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Make sure the cam is mounted securely before using to the avoid risk of tearing the flatflex. Contrary to other designs the grabbing teeth have a tiny angle to them, they get thicker in the middle. This allows for slight off-center usage…
Wydruk około 0,07 €–0,09 € nettoWstępna wycena jednego wariantu
1. Introduction This is a remix of a remix (Scatterthought) of a good Logitech C270/C310 Focus Ring design. I just add my contribution ;) -Tighter tolerances between ring and cover. -Change the “gear” design to better grip the lens.…
Wydruk około 0,50 €–0,61 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Hallo Freunde der Audiotechnik, anbei gibt es STLs und G-Codes für einen Focusrite 4i4 (3rd Gen) 9,5Zoll Rack Halter. Ihr braucht für ein komplettes Set folgende Teile: 2mal Rackmount 2mal Stabilisierer Top 2mal Stabilisierer Down…
Wydruk około 1,84 €–2,25 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a snug fit for the Clarett/Clarett+ 2Pre (including its rubber feet) and the latches hold the interface firmly in place. So it's no problem to plug in/out an XLR cable with one hand. Yet, after disconnecting the cables on the…
Wydruk około 5,58 €–6,82 € nettoWstępna wycena jednego wariantu
Similiar to my other tow hook for german vehicles, I designed this from scratch for the Ford Focus MK2 as its tow hook has a different shape. Printing: a lot of walls (~4-5) no support needed if printed standing upright! PLA works, maybe…
Wydruk około 2,63 €–3,22 € nettoWstępna wycena jednego wariantu
Es handelt sich um einen Trichter für das Scheibenwischwasser des Ford Focus Modell 2021. Der Trichter hat einen unteren Durchmesser von 46 mm und einen oberen Durchmesser von 125 mm. Die Höhe beträgt 155mm über der Einfüllöffnung, so…
Wydruk około 6,04 €–7,38 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ford Focus MK4 Quadlock adhesive mount adapter for Aliexpress phone mount Quadlock dashboard/console mount doesnt stick on the dashboard material and couldnt find a good location. So i combined it with this dashmount from Aliexpress…
Wydruk około 0,81 €–0,98 € nettoWstępna wycena jednego wariantu
Free calibration grid for diode and CO2 laser engravers. Tests power (10–100%), speed (100–1000mm/s), line width (0.1–2mm), and greyscale fill in one 200×160mm sheet. HOW TO USE: 1. Open the SVG in LightBurn, xTool Creative Space, or…
Wydruk około 0,08 €–0,10 € nettoWstępna wycena jednego wariantu
You will need a fiber laser cutter to cut the 1mm Inox gauge, and a 3D printer to print in PETG the support, 0.4 nozzle, 4 perimeters, 0.2 layers, support on the plate only ! printing orientation: square hole entry face the plate ! the…
Wydruk około 0,25 €–0,30 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Plastic style: To be printed in a non-brittle, non-warping material, PETG and PLA+ are perfect. On a good 3D printer with a good precision ... A millimeter must be a millimeter ! Print your tabs, along with the nut and bolt. Don't rush;…
Wydruk około 0,88 €–1,08 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ford Focus MK4 brackets to stick the Aliexpress ambient footwell LED's on. The brackets will fit into the original mounting positions where normally the factory ambient lights will be installed. Somehow left and right have a slightly…
Wydruk około 0,89 €–1,08 € nettoWstępna wycena jednego wariantu
I've created this nema 11 stepper motor mount for my ASKAR FRA 400 telescope. I give as well my dew shield for this scope. You have to found the adapter piece (coupling) 2.5mm to 4mm (stepper to focuser) as I've not designed myself.
Wydruk około 5,97 €–7,30 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Diffuser fitting a Ford Focus MK4 to install Aliexpress ambient lights.
Wydruk około 0,12 €–0,14 € nettoWstępna wycena jednego wariantu
This angled stand is designed for the Focusrite Scarlett 16i16 USB audio interface. Improved visibility: Tilts the unit 15° for better viewing of input meters and front panel LEDs at desk height. Cable-friendly: Raises the interface…
Wydruk około 4,30 €–5,26 € nettoWstępna wycena jednego wariantu
This is a 0.8 MOD gear 65T for the 3" V-Power focuser of William Optics, that is intended to be used with Tilta Nucleus-M wireless lens motor (https://tilta.com/shop/nucleus-m-motor-kit-i/ ) for wireless focusing control, or ZWO EAF…
Wydruk około 1,28 €–1,56 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a 0.8 MOD gear 60T for the focuser wheel of Pentax 75SDHF telescope, which is used for focus automation via ONSTEP ASCOM driver.
Wydruk około 0,95 €–1,16 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a 0.8 MOD gear 44T 55T 66T for putting on the micro-adjustment wheel of 2" V-Power focuser, and it is intended to be used with ZWO EAF stepper motor installed with 22T gear (…
Wydruk około 0,45 €–0,55 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The Focusrite Scarlett 2i2 (4th gen) has a circular volume LED around the input 1 and 2 inputs. At the time of this file's creation, there is no software solution for disabling it. This knob was designed to block out that light. This knob…
Wydruk około 0,14 €–0,17 € nettoWstępna wycena jednego wariantu
This is a 0.8 MOD gear 60T & 65T for the 2.5" & 3" Feather-Touch focuser of Starlight Instrument, that is intended to be used with Tilta Nucleus-M wireless lens motor (https://tilta.com/shop/nucleus-m-motor-kit-i/ ) for wireless focusing…
Wydruk około 0,86 €–1,05 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a 0.8 MOD gear 60T for the 2" Feather-Touch focuser of Starlight Instrument, that is intended to be used with Tilta Nucleus-M wireless lens motor (https://tilta.com/shop/nucleus-m-motor-kit-i/ ) for wireless focusing control, or…
Wydruk około 0,80 €–0,98 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Boost your productivity and elevate your workspace with this "Focus" Lightbulb & Gears Wall Art ! Designed specifically for student desks, study rooms, makerspaces, and home offices, this piece seamlessly combines a brainstorm lightbulb…
Wydruk około 0,51 €–0,63 € nettoWstępna wycena dla PETGMateriał u źródła: PET
0.8 MOD gear 72T, 75T, & 90T (for the focuser wheel of Pentax 105SDHF telescope), which is used for focus automation via ONSTEP ASCOM driver.
Wydruk około 1,16 €–1,42 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Wallmount for E-Bike 378wh T.E.C Pack Battery of E-Bikes from Focus Jam2 / Jam2 HT / Bold2 / Sam2 with Shimano E8000 motor. Mountable with two screws to a wall or, using the holes on the backside with 2 screws (Phillips Rounded Head…
Wydruk około 1,02 €–1,25 € nettoWstępna wycena dla PETGMateriał u źródła: PET
0.8 MOD gear 60T (for the original focuser wheel of Takahashi FSQ106N telescopes) , which can be applied for focus automation.
Wydruk około 0,87 €–1,06 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A simple privacy cap for the Logitech C270 - Focus Adjustment Mod . ⌀ 17mm with an inner slope of 0.2mm - may fit other similar mods. Features No supports required ✨ Extremely fast print (≤2 min) 💨 Print ≤0.20mm layers recommended What…
Wydruk około 0,04 €–0,05 € nettoWstępna wycena jednego wariantu
0.8 MOD gear 60T (for the original focuser wheel of the Takahashi FSQ85EDP telescope) , which can be applied for focus automation.
Wydruk około 0,88 €–1,07 € nettoWstępna wycena dla PETGMateriał u źródła: PET
0.8 MOD gear 60T (for the original focuser wheel of the WO Z61-III telescope), which can be applied for focus automation.
Wydruk około 1,05 €–1,29 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a design for a generic automotive part, which allows you to print as 3 separate pieces that fit on a standard size printer bed. It's a remix of a design originally by TinaBelcher, thanks Tina! Designed to fit my 2017 Focus ST LZ,…
I'm adding a tool for fine-tuning the focus of the OV2640 camera module. Currently, I have designed a bracket only for the first 3 commonly used lenses for the OV2640. Support for OV8225 camera lenses will be added in the future. WARNING!…
I needed a mount for my scarlet 2i2 to declutter my desk, so I drew up this design, intended to mount wit 4 countersunk screws. The audio interface slides in and is held in place through a tight friction fit, sturdy enough to not move…
I found several existing mounts for the Focusrite Scarlett Solo (3rd Gen), but all of them had some fancy locking mechanism and/or required supports to print properly. More importantly, it looked like all of them were too close to the…
The Hadley telescope by Maff is a great design that allows makers for an easy and cheap introduction to astronomy. There are lots of difficulties when using a telescope for the first time, for me one of them was trying to take a picture…
Introduction A selection of remixed focuser options for Hadley , all designed from scratch with 45deg threads and 3mm pitch for vastly improved printability and operation. Mostly remixes of Hadley focusers that are out there in the wild,…
Discussion A replacement mainboard cover for the Qidi Plus4 that allows for the use of an 80x25mm fan This is a variant of my other honeycomb design posted on Thingiverse This variant positions the fan more centrally over the hottest…
(From time to time I am asked "Will it work/Could it mount on my X telescope?" for various values of X. Well if I had an X, I would make it work. You could send me an X! But it's cheaper if you make a simple adapter plate - If you don't…
Modification to adjust the Focus on a Logitec C270 Webcam. Be aware that if you open the Camera the Focus Ring is glued into place. You can Remove this glue with a small Screw driver. Additionaly you will need 2x M3x8mm Screws to mount…
Description A replica of the focus tool that comes with Creality Falcon 2 laser machines. Use it to replace misplaced tools or to have some spares just in case. The dimensions are: 7mm for engraving and cutting of 1-3mm thick basswood 5mm…
The camera mount is aligned to see the nozzle close up even when doing a nozzle wipe and calibration. This is the best current option for the Kobra 2 Series printers uses external Wyze App. Does Not work with Anycubic App. The reason this…
This tool is to hold the laser focus spacer used on the Falcon 2 22w laser engraver from Creality. I wanted to make sure I didn't misplaced the tool - attaching it to the front of the unit is the obvious choice as it's accessible event…
Remix of @Christoph_79778 's Scarlett 2i2 mount, widened to match the dimensions of the newer 4th Gen.
Description FORD FOCUS ST UMBRELLA HANGER I took inspiration from the model and modified the model allowing for a more secure fit and adding the ST logo for Fords! It all looks very nice and makes everything more racing! Print it and…
230425: v0.1 inital version Work in progress for a proof of concept that a focus helicoid can be made by 3D printing. Currently printed in 0.1 layer height in eSun ABS+ on a Voron Trident. This version should result in ~6mm movement and…
Focus adjustment tool for Raspberry Pi Camera V2 Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 50% Category: 3D Printing
Does not require support material Print with back face (power cord plugin area) on the print bed
The faceplate in Night Gryphon's Logitech c270 webcam manual focus adjust ring is perfect, but the lenses on newer C270s have a slightly smaller diameter than old ones. As a result, the focus ring doesn't fit. I adjusted the inside…
Hello, I've finally found a permanent solution to prevent plastic clips from falling off the trunk shelf. I used M3 screws that are 20mm long, but shorter screws can also be used. Material: PLA, infill: 100% Supports are not necessary.…
I discovered the other day that I needed to adjust the focus on my Creality Nebula Camera, and my fat fingers found it particularly difficult to make the fine adjustment necessary, so I designed the Nebula Camera Focus Pull: a simple ring…
Hello even more creative DIY Cine / Movie Making Amateurs and Professionals, This was a Long Lost Generator. Gladly some people make backups and modify it so it can be used more easily. Install OpenSCAD from https://www.openscad.org/ Open…
This is my adjustable focusing stick that I use with my fiber laser. The 3mf files include three parts: 10cm wide top end of stick 15cm long bottom end of stick (short version) 20cm long bottom end of stick (long version) The short…
Perfect for multicolor printing. Material: PLA Layer: 0.28 Temperature: 200°C
Updates! Reorganized parts listing for clarity About After spending some time trying to use a telescope camera with the wonderful Hadley telescope by Maff , I decided I needed a focuser that didn't rotate. Rather than wait, I decided I'd…
CHOOSE WHAT YOU LIKE: A single complete piece / two parts Choose if you want your Scarlett to be removable or not - also a few options on how removable Additional cable holders with various sizes Honeycomb may save print material I…
Under-desk mount for the Focusrite Scarlett Solo audio interface, mounts with either 3M double sided adhesive tape, or with screws up to 3.5mm in diameter. The mount consists of two pieces which are mirror images, both pieces print…
My laser cutter is up on risers for rotary engraving so I didn't feel like laser cutting the ruler, here's a 3D printable version of it.
I printed it in PETG on a 0.6mm nozzle at 0.4mm layer height with supports for the fillet of the screw wing. It's very snug - it does not budge when pulling out an audio cable. Print it in the direction of the STL as the back has an inset…
The Wyze Cam V3 is an excellent, affordable little camera to monitor your printer, but it has one fatal flaw... focus distance! The camera comes with a fixed focus that's approximately 3 feet to infinity, which makes monitoring 3D prints…
I have a Ford Focus 2012 (Hatchback) and after 9+ years of prolonged heat, the windshield wiper tank cap decided to disintegrate. I whipped this up it Fusion 360 and printed it in PETG. This cap may fit newer ford(s) vehicles. Update…
Seatbelt cheater designed for a 2010 Ford Focus. For all legal purposes, or whatever, I'm not your mom. Category: Vehicles
Experience the ultimate in track performance with this 3D printable STL model of the Mercedes-Benz AMG GT Black Series 2023. This track-focused supercar model is perfect for automotive enthusiasts seeking to display the aggressive…
A tow hook cover for the Ford Focus MK3. Build year 2011-2018. Its my first time designing something for a 3d printer. But it turned out alright I think.
This is a funnel I created for topping off the brake fluid level for my '15 Ford Focus. Like many cars made now, the brake fluid reservoir is actually recessed under a cowl. I wanted a simple way of topping off the brake fluid level while…
The main tool of the hero of the Horizon: Zero Dawn game Print instructions The main tool of the hero of the Horizon: Zero Dawn game
A replacement mainboard cover for the Qidi Plus4 that allows for the use of a 92x25mm fan. I found that 92mm 24V fans were less expensive than 80mm ones so it's a good tradeoff. Here is the specific fan I used…
Support à fixer sous un bureau ou un plan de travail pour la carte son Focusrite Scarlett 2i4 2nd Gen et 2i2 2nd Gen Je voulais un support qui me permette de sortir la carte de son logement en cas de besoin. Attention, les languettes sont…
Cet outil vous aidera grandement à régler les problèmes de Front focus ou de Back focus dont sont parfois (souvent) victimes les objectifs de nos reflex photo, à condition que votre boîtier dispose de l'option du micro-réglage de…
This is a wall mount specifically designed for the Logitech C270 webcam (with the base removed), a replacement faceplate, and a focus ring to adjust the focus on the fly. The faceplate and focus ring are a remix for my specific use case.…
I have a Ford Focus 2012 (Hatchback) and after 5 years of prolong heat the windshield wiper tank cap decided to disintegrate. I whipped this up it Fusion 360 and printed it in PETG. This cap may fit newer ford(s) vehicles. Print…
The Ford Focus MK2 has a pretty terribly designed cup holder, and with todays drink sizes it fall short quite a bit. I've designed this cup holder adapter that solves this issue and can hold up to a 10cm diameter bottle, and moves the…
This project is designed to help you stay on track with your focus sessions, using a simple and intuitive interface via a rotary encoder and an OLED display. Whether you need to time focused work, breaks or other worthy pursuits, this…
If someone else is trying to fit a 3 way speaker setup into an “old” Ford Focus mk2 (2004-2010), maybe this will help. The tweeters and mid drivers are directly focused on the left seat headrest, depending on your speakers and lisening…
A customizable OpenSCAD (free and open source: https://openscad.org/ ) focus mask generator. Can generate masks for various telescope types and photo camera lenses as a filter via the OpenSCAD customizer…
I remodeled the original model to make it much more sleeker and use a lot less plastic. there are two slide models . depending on the calibration of the printer one is a bit tighter than the other. you need m2.5 x 6mm x 5 thread inserts…
A simple bracket to hold a 4i4 Audio Interface to the bottom of a desk. Has recessed 3mm holes for a variety of screws.
ArduCam IMX519 https://www.arducam.com/product/imx519-autofocus-camera-module-for-raspberry-pi-arducam-b0371/
This is a modified mounting plate of 1.25" Crayford Focuser for telescopes by aeberbach for use with Hadley telescope. This focuser is a massive upgrade in functionality compared to any printed helical focuser. Attaches to the Hadley UTA…
In my Ford Focus MK1, the sun visor retainer has aged and fallen out. I can't find anything similar here, so I designed one. It fits tight, doesn't sag. I've printed from PLA, but maybe something softer, more flexible material would be…
Didn't like the standard battery that the original poster made as it needed supports and looked horrible when printed. This is about 3mm bigger on the outside and has more room on the inside for the larger makerfocus battery and most…
I am proud to present to you “ Hypatia ”, my take on a focuser for the Hadley Telescope ecosystem. It combines what I consider to be the best features in other designs, and some ideas of my own: the Crayford style of focuser - which uses…
Introduction: Photographic bellows is a very efficient tool that allows to achieve high magnification ratios with pretty much every lens. Below you can see a gif composed of three images taken using Cosina COSINON AUTO MC f/2.8 135 which…
This is a custom made tool to adjust the focus of P5V04A camera used on the Rapberry Pi Camera v1.3. Just fixate the camera with the body and adjust the lens with the tool.
Non rotating helical focuser for a precise focus which can easily be attached to your telescope, or a precise variable extension for photography and visual observing. The orientation of the camera is maintened during the focusing…
Print Information: Printer: Prusa-Mini Filament: PRIMASELECT PETG Transparent Black Nozzle: Bondtech 0.4 Layer high: 0.2 Infill: 50% cubic Rafts: No Supports: No Gedruckt wird flach und nicht hochkant. Zum kleben verwendet man am besten…
The original design by Daeloth was great, but I wanted to add the blue coloration without any LEDs or lighting, so I cut a slot and created another piece to be printed in blue (or whatever color you want it to be). The finished result…
I was looking for a good solution to make the focuser motor work with my Samyang 135mm lens on the OAT. I decided to just design my own. I think this ended up working well. There are two sets of rings, small and large. The small rings…
This is a simple plate that is 3.8mm thick with a little handle on one side. To use it, lower the acrylic guard down onto this plate and tighten the screws. Then the laser will be in focus for the material you are using. I'm not sure if…
Under-table mount for Focusrite 2i4 2nd gen audio interface This is a remix of the 2i4 bracket by DJERO . The design has been modified to be printable on the side, and require no supports. Printing on the side should also make the tabs…
A vertical stand with a perfect fit for the Focusrite Scarlett Solo. Free some space on your desk !
I previously had a Scarlett 2i2 Gen 2 mounted under my desk with the mount from ziller88 . After the Interface died i bought a 2i2 Gen4 and modified the mount to work with the new interface. It comes in 4 Versions: Scarlett 2i2 Gen4 desk…
Small October 2022 Status Update (original models generated July 2021): I've made a couple of these and they've held up well - after over a year of light daily usage, they still work! This is M42-4-E-Var, a focusing M42-screwmount to Sony…
V2 3D printed 1:10 reducer for crayford focusers Update History 2) Integrated needle mod and V1 small button alternative - Integrated needle mod within original file. You can still like and download here or from remixes list. - Added…
make sure you don't over extrude when you print this (top wall is 0.6mm)
--- 04.01.20 update II --- Added first test image. No light leaks! Even without any light foam seals around the film holder. Should still be added though, to increase distance to lens, so that infinity is in focus. Infinity is now in…
Sensory Dog Tag Token Collection – Pocket Focus Buddies! NEW MODELS!! Choose from: The OG, The Breather, The Speedway or The Bumps! A tiny swirl of calm for busy hands. These pocket-size tokens pack a handful of tactile “mini games” you…
This is a Focusing handle for Zeiss 80mm V system lens. I used a 4-40 x ¾ socket cap screw along with a standard 4-40 brass hex nut.
Under desk mount for the Focusrite Scarlett Solo 4th Gen. (note: 3rd gen and 4th gen are different sizes, 4th gen is bigger so this will not fit the 3rd gen) Designed to not require supports, to allow this it should be printed on one of…
This is an under desk bracket for the Scarlett Solo 3rd Gen. 4x #4 countersunk screws XLR cable clip is 6.5mm wide Print with support everywhere with back the side, where the cable clip is, down.
funnel for ford focus 2 (windshield washer fluid) or other with hole bigger than 32mm. Printed with PLA (use brim, no supports)
Update 2019-09-29: Added a few more photos to help illustrate the disassembly and assembly process. I'm using a Logitech C310 webcam in conjunction with Octoprint on a Prusa i3 MK3 (and another on a MK3S). The focus setting on the C310…
