51 modeli
About The price of original retract (1-01759) seemed rather high for a pack of screws and plate of milled plastic, so I decided to design my own based on photos available on the internet. I had to alter some dimensions (mostly main body…
Wydruk około 11,68 €–14,27 € nettoWstępna wycena jednego wariantu
This is a spare locking clip for my Multiplex transmitter tray rain cover “SpaceBox”. I printed in ABS, layer 0,15mm, brim+ support, standing on one side ( so to have the maximum resistance when the clip gets pushed in.
Wydruk około 0,56 €–0,69 € nettoWstępna wycena jednego wariantu
Mould for cable "aftercare" for Multiplex 6pin connector used in RC models. Print instructions Printed with ASA, dipped in acetone (optional). Layer height 0,2mm. The same mould used for the male and female connector. Be careful with the…
Personnally, I printed it with ASA but I guess PETG and ABS may be used too.
I took over this rudder horn from the Multiplex Indoor Extra, because I was very happy with it. Before printing you have to enlarge the part by 100 times. I hope you enjoy building :) Print instructions Unassociated tags: rudder horn…
FPV canopy for the Multiplex FunRay RC plane. Designed for the Walksnail Avatar FPV system but should fit any other standard FPV camera as well. The two pins for the original latching mechanism are printed separately and should be glued…
This parachute release hatch for multiplex funcub ng is a nice addon to drop toy parachutes or sweets or other small things. The hatch is released by a servo and with this design the hatch doors can also be closed again after dropping…
This nose cone assembly for the Multiplex Funray RC clider consists of three parts, which are screwed together with M3 screws. Inside the cone, you can add up to roughly 10 washers with 10mm inner diameter to adjust the center of gravity…
Canopy Holder latch, compatible to MPX (Multiplex) R/C plane models e.g. Easyglider, Easystar, Cularis... (current version with hole / clip snap concept) Inspired by thingiverse object #806001 "mpx_kabinenhaubenhalterung.stl", but I…
simple skids to protect the bottom of your precious Easyglider Print them with 0 infill and two perimeters. Hot glue under the wings. Print Settings Printer Brand: Prusa Printer: i3 MK2S Resolution: .3mm Filament: none PETG white…
New mould for MPX connectors, for male/femelle Category: Toys & Games
This is a tube rack for holding Qubit tubes, meant to increase your pipetting efficiency by 4x. Each section is spaced so that you can use an 8-tip multichannel pipette to add reagent and samples 4 at a time, making your life 4x easier…
Pult für Multiplex Cockpit SX 9 (7 & 12).
After a couple of years my viega bathtub knob broke down. So i designed a replacement. It supposed to replace knobs that looks like this: You can print it without any supports. You can edit how it looks - just download f3d/step file and…
This is a mold for Hot Glue allowing to secure connections of wires/soldering with the plug Print Settings Printer: fabrikator mini 2 Rafts: No Supports: No Resolution: 0.2 Infill: 50% Category: DIY
Installing the battery of EasyGlider is critical to insure good balance of the plane (CG position at 70mm). Multiplex proposes to use "Velcro" tape to fix the battery into the fuselage. This is not simple neither efficient... I have…
Mit nur 2g ist dieser Halter für einen Multiplex RX7 light Empfänger extrem leicht und ein muss für jedes Modellflugzeug. Druckparameter Material ASA Drucker Voron 2.4 Support Tree support Layer hight 0,2mm Infill 15%
Multiplex Manchester coding is a type of encoding system where each data bit is either low then high, or high then low. This self-clocking signal was widely used for data recording and is still in use in various systems today. This basic…
GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount The gopro is behind the cw, check the cw from your funcub before the start. With a hot air blower you can bend wing shape, but it is not necessary,…
Hexagon wall art, using multiplex hexagons and printable clip-on hexagon pattern. Printed in 0.2mm layer height, 6 perimeters for strength, and good-looking bottom layers (concentric bottom layers may also work). The printer part will…
Just a simple addition to Sjefke's FPV platform for the easystar 2 so that i could mount a cheapo board camera. The hooks hold it onto the original Easystar 2 mounting locators, you'll need 2 of course. The camera bracket fits a board…
Version 3 GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount. The center of the GoPro is over the CW (ca. 80mm) A recess for the ttow release available. With a hot air blower you can bend wing shape,…
Tragevorrichtung für Modellflugzeug “FunCub NG” von Multiplex. “ Carry ” wird mit den beiden Schrauben der Flächenbefestigung an den Rumpf angeschraubt. Es sind Vorrichtungen zur Befestigung der Flächenstreben enthalten. Dadurch kann man…
Two-piece mount for retrofitting a nose gear on the multiplex Twinstar. For more stability, a brass sleeve must be inserted into the mount. The gear wire is then secured with set collars.
Mechanical multiplexer shown here: https://www.youtube.com/watch?v=8DWK3zm9SMs 10/21/2018: added design files for openscad Note: all screws are #6 1/2 inch pan-head sheet metal screws (except for stepper motor which requires M3 machine…
Roof or wall hanger for your Multiplex Easystar 3 (could work for other versions of the plane, but I have not verified that). The aft hanger (for the stabilisers) includes a hook for securing the model with rubber bands 5 mm hole for…
MPX Steckerschutz oder zur Anzeige des Ladezustandes. MPX plug protection or for displaying the charge status. Print Settings Printer Brand: Artillery Printer: Artillery Sidewinder X1 Rafts: Yes Supports: No Resolution: 0.2 Infill: 5%…
This holder is designed to hold the RX 7/9 DR M-Link from Multiplex. I used double sidedtape or glue to fix the holder inside the plane. In more than 2 years of using this mount my recievers never slipped out, despite of no fixation of…
Print the two parts and insert the TCA9548A multiplexer inside them then pull the source wires going to your controller through the small slot on the back side of the adapter. Use the larger front opening of the adapter to connect the…
Hier einen Modellständer für den Lentus von Multiplex. Es werden noch 2 Aluminiumrohre mit einen Außendurchmesser von 15mm und ca. 430 mm lang benötigt. Gestell Vorne / Hinten mit dem Boden verkleben. Here's a model stand for the Lentus…
I printed my final version with no supports, PLA, 90% infill, 3 walls and it seems strong enough. (edit) i still haven’t flown this design as I rarely go to the spot that’s big enough for the easy glider. I am still running the pla motor…
I lost the tailwheel-mockup for my well-used Multiplex-Solius and glued a piece of wood in place, as a placeholder. Finally came around to model a replacement-part. Ich hab das "Spornrad" an meinem Multiplex-Solius verloren und hatte ein…
My Multiplex switch case had been broken, so i draw and printed a new one. This is made out of ABS 70% infill. I lighlty filed/sanded the exterior face to have it smooth. Clean the holes with a drill bit (1,5mm) and you're done.
Antenna socket for the Multiplex mc2020 / mc2010 R/C transmitter, to replace the original "telescopic" antenna socket. Just snap into the transmitter housing instead of the original one. A standard 2.4GHz antenna sockets fit well into…
The gimbals of the old Multiplex Profi mc transmitter series are a good basis of a DIY or retrofit transmitter project. Unfortunately they use 5kOhm sliding potentiometer as trim inputs which no modern transmitter mainboard (e.g. Turnigy…
Englisch: Guide rail for the multiplex plates, for the construction of my pinball machine. I wanted to be able to remove the plates at any time if I needed to make changes to the electronics or add something else. This is the perfect…
Printed with Bambu Lab X1C + AMS. Colors needed: white, black, orange. Also Available as svg vector graphic More info about Multiplex WINGSTABI: https://shop.multiplex-rc.de/de/wingstabi-evolution-7ch-p3584/?search=1
3D printable motor mount for standard brushless drone motors, compatible with the Multiplex Funwing. Hole Pattern 12x12mm As accessories, you'll need 3 short M3 heat-set inserts from cnckitchen. Recommended materials are PETG or PC Blend…
Use this if you need to connect multiple I2C devices with the same address to one bus. Uses a plain PCA9548A module mounted at the bottom of the PCB. Contact me if you are interested in the PCB. Category: Electronics
This is a desk hook I designed to hold many difirent bags off tables,desks extra. What makes it convenient is that it fits on multiple desk sizes not just one. That way you can put it in your bag and use it wherever you are. it has a high…
Adaptateur pour connecteurs Multiplex 6 pins pour l'ASW-15 4m 2026 V1 ( https://cults3d.com/:3834288 ) Paramètres d’impression Infill 5% Top-Bottom: 3 Wall: 2 PLA
I made this small box to fit my specific purpose to be able to track temperature and humidity in 3 different location (outside greenhouse, inside greenhouse and inside the “winter tent” in the greenhouse). I control a heating fan from…
This is a 1x2x4 Gridfinity bin that can store up to 10 TCA9548A I2C multiplexer switch modules. See the photos for the specific board this design is based on. I'm not 100% sure if the Adafruit version of this module will fit, but I…
Ich würde es stehend drucken und mit 100% infil. Ich habe das Model gemacht weil ich kein Ersatz teil gefunden habe .
These wallmounts are for the AvenuePad3 controller and the controller Multiplexor for the PC Engine / Core GrafX. It may be compatible with other AvenuePads but that has not been tested. See my design list for wallmounts for other…
These parts allow one to replace the RF stage of a Multiplex Royal Evo with a nano sized RF module, typically for running ExpressLRS. A build log can be enjoyed here: Additionally, this design is available at…
Ich würde es stehend drucken und mit 100% infil. Ich habe das Model gemacht weil ich kein Ersatz teil gefunden habe .
These wallmounts are for the AvenuePad3 controller and the controller Multiplexor for the PC Engine / Core GrafX. It may be compatible with other AvenuePads but that has not been tested. See my design list for wallmounts for other…
Use this if you need to connect multiple I2C devices with the same address to one bus. Uses a plain PCA9548A module mounted at the bottom of the PCB. Contact me if you are interested in the PCB. Category: Electronics
About The price of original retract (1-01759) seemed rather high for a pack of screws and plate of milled plastic, so I decided to design my own based on photos available on the internet. I had to alter some dimensions (mostly main body…
Wydruk około 11,68 €–14,27 € nettoWstępna wycena jednego wariantu
FunCub GoPro GoPro_Mount MPX Multiplex Version 3 GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount. The center of the GoPro is over the CW (ca. 80mm) A recess for the ttow release available. With a…
