203 modeli
Very quickly slapped together Stringing Test. Markings 1cm apart so you can post-process z-height changes. Deliberatly no temperature numbers b/c they confuse when you use different temperatures (or - like me - test retract distances…
Wydruk około 0,67 €–0,82 € nettoWstępna wycena jednego wariantu
A perfect model to test your printers ability to properly retract filament, and test its bridging capabilities. This is done with two small towers either side causing the printer to have to travel across the middle on each layer. If the…
Wydruk około 0,24 €–0,29 € nettoWstępna wycena jednego wariantu
Test the Circle Kalibration
Wydruk około 0,15 €–0,18 € nettoWstępna wycena jednego wariantu
These are 2 versions of a bubble level adapter for the Gamma X-Stringer X2 stringing machine. To ensure consistency of the pull, the lever of the stringing machine should be dropped parallel to the ground every time. Experienced stringers…
Wydruk około 0,23 €–0,28 € nettoWstępna wycena jednego wariantu
Economical and fast to print string test for quick iteration over different parameters that might influence stringing on your printer. Printing Parameters Print this in the layer heigth you want to use or a medium setting, something like…
The Eiffel Tower showed up with some stringing. This Test Model is intended to vary parameters Print instructions PLA Prusament 0,15 Standard Quality Mode
I designed these to be printed very quickly so you can test your retraction settings without wasting a lot of time/filament.
Rather than setting layer temperatures manually for a temp tower, just include one line of G-custom code in PrusaSlicer's “before layer change G-code" section to do it automatically. You can use the attached .3mf file as a starting point…
Since I could not find the ideal temp tower that meets my expectations, I designed my own. Features: - Uses little material because it is not too big - Different overhangs, 45° and a curved one - A thin wall at the overhang to test the…
Activate firmware retraction in your slicer. Activate firmware retraction in klipper by adding this to you printer.cfg : [firmware_retraction] retract_length: 0.8 retract_speed: 60 unretract_extra_length: 0 unretract_speed: 60 Slice the…
No fancy settings, simple design. You can Support me by making a small donation: https://www.paypal.me/sharad1209
This test part is optimized so that you can print it quickly to achieve many iterations in a short period of time without wasting too much filament.
Stringing Test für PETG mit unterschiedlichen Temperaturen. Von unten 260°C bis 235°C
File for testing retraction
petit test pour le stringing Print Settings Printer: Alfawise U30 Rafts: No Category: 3D Printing Tests
Read the guide on stringing and oozing: https://help.prusa3d.com/en/article/stringing-and-oozing_1805 Test different retraction lenghts and temperature settings. About 8 minutes print time.
Another stringing test, prints fast, requires little filament. Prints in 10-15 minutes.
A small but effective Stringing test
A few different stringing test. Because models are different so this will help to test stinging. They can be used for any type of filament.
Battle stringiness by enhancing retraction and/or wipe, or eliminating Z-hop. At the end of the day, a good quality filament or a very dry one will just not string. The two white prints in the picture are simply befor and after a spool…
diameter : first circle:3mm second circle: 5mm square:4x4mm and last random shapes separated by 2mm the whole is 80x20x41mm (without a base 40mm)
There are already many calibration and test parts to get rid of the stringing of your printer, but this one is optimized so that you can print it quickly to achieve many iterations in a short period of time without wasting too much…
Stringing Test Tower with notches every 5mm. Stringing Test Turm mit Kerben alle 5mm.
Just a simple Stringing-Test 0.6mm base height + 25mm Tower height = 25.6mm Wall thickness = 1.2mm Print Settings Printer: Anycubic Mega-S Rafts: No Supports: No Resolution: 0.2 Filament: Printament PETG/PLA/others Green Category: 3D…
Print this model to fine-tune and test your slicer settings and get rid of annoying stringing. This is the original, Basic Stringing Test by Loohney with over 160,000 downloads on other platforms. Angus from Maker's Muse has an excellent…
Very tiny test print I designed to test the level of detail I could get from my settings. See attached pictures for all measurement details. This print tests dimensional accuracy, curves and spheres, holes, bridging,…
I made a stringing test using FreeCad as a resource. See also my FreeCad calibration cube !
Test the optimal temperature for your filament to reduce stringing. It includes custom gCode to automatically change temperature from 240-200°C. A negative volumetric box is added to exclude temperatures 190-180. It can be changed…
Designed with using firmware retraction in mind. Tested with 0.4 and 0.6mm nozzles at layer hights up to 0.4mm. If a smaller nozzle is used, scaling it may be an option. First picture shows the default dimensions and distances, second…
This is a simple ground/dirt anchor for vertical trellis vegetable stringing (in my case, tomatoes). Simply tie your string around the knob at the top, then screw the anchor into place near the base of your tomato plant (trying to avoid…
Uses under 1 gram of filament with 0% infill and 2 perimeter walls.
Temp of nozzle is the main cause of stringing. Print this gcode before trying other adjustments. It starts at 220C, and automatically decreases 5C after each 5mm increments, ending at 180C The picture shows the results when filament is…
Reverse engineered the load spreader, the piece that holds the top and bottom of the racket for equal stress distribution. Printed with PLA or PETG at 0.1mm with supports.
The Advanced Retraction Test allows the user to tune retraction while taking into account variable distance. This uses 4 pillars that start at 5mm tall and increments by 5mm. 5, 10, 15 and 20mm tall. This allows you to change retraction…
I have desinged a few test models and hears what you need to know about them: Calibration Cube: Print Time: 20min Size: 15x15x15mm It tests how acuate the X,Y, and Z belts are. After it prints you need to mesure it.(with something more…
simple stringing test to see if you have problem with stringing
this is a quick little test print to test your retraction settings
These are the details for perfect stringing models- Layer Height- 0.15mm First Layer height- 0.2mm Retraction distance - 8mm Retraction Speed - 30mm/s Print speed - up to 130mm/s
Not much to say here, print it with your normal settings and see if it looks awful, acceptable or perfect!
A fast retraction test that also tests your printer's overhang up to 75°! This is a useful calibration test tool that uses less than 2g of filament! Feedback and Makes are always appreciated, If you're up for another challenge, check out…
Hier handelt es sich um einen einfachen Strining Test. Man kann mit Hilfe des Modells an den Druckeinstellungen feilen.
If blobs are seen on the strings between the posts, the filament is definitely wet. Strings are ok as long as they are smooth and fine.
A simpel stringing test. Uses a minimum of material and time.
a stringing test to help calibrate your printer
A simple print to test stringing on ur 3d printer.
A stringing test for your 3d printer to test it's retraction
Tools for Tennis Racket Stringers Spacer Blocks or Bumpers are tools for use in stringing Tennis (and possibly other) Rackets. They are placed temporarily on the string between the starting clamp and the frame during the stringing…
Created this small cube that should be 20x20x20mm to test stringing + bridging capacity. Quick and use little materials. It also pairs as a fun optical illusion.
I still saw multiple weird artifacts in my prints even after dozens of successful retraction tests. To tackle those edge cases I designed this mini retraction torture test with multiple edge cases. On the top of the print you have quite…
Features: - Uses little material because it is not too big - Different overhangs, 45° and a curved one - A thin wall at the overhang to test the layer adhesion by breaking it - A bridge, from 30mm length in the back to 35mm in the front -…
This test was built to test stringing under unfavorable conditions in the minimum amount of material possible. I designed it because I had consistent stringing issues and printed larger stringing tests over and over, wasting about 2kg of…
HIGH STRINGING TEST STING Category: 3D Printing Tests
A Retraction / Stringing Test collection How to print: I print this one on the Bambu Lab P1P with the following specs: Bambu Lab Standard Profil for the P1P 0.2 only the Layer width has been change Layer height: 0.2 Layer width: 0.4 First…
A simple test for bringing and stringing performance. It is very fast and costless in terms of filament. About 4g of filament and 15-20m test, you can obviously scale it in the slicer if you wanna. I needed a fast test for a fast tweaking…
Flipped into the correct orientation version of the original model . Printing tips: Use 0% infill Use Seam painting tool in PrusaSlicer to achieve uniformal seam for testing:
Stringing machines usually comprises a sturdy metal frame, clamps to hold strings in place and a tensioning system to tighten strings. Electronic models have control panels for precision stringing but do cost a lot more. The KhordUino…
inTinker's stringing calibration. Single.
It's very basic but if anyone wants it you're more than welcome. Just duplicate, flip over and you have the test as per my videos.
This is more or less a remix of the linked Nano All in One 3D printer test. I printed all of that just fine except the overhang after 45 degrees. It took me awhile to dial in the settings to get my overhangs looking good. After probably…
This is a more thorough stringing torture test. This prints best with a brim and tests both your printer and you slicer to reduce stringing in multiple directions. This is not originally my file. I would be happy to give attribution but I…
I've made a simple Stringing Test because i thought everybody need one.
Easily test the stringing of filaments. Approximately 13 min. Calibration requires many trials, so use a simple test model.
This is the ultimate stringing test V4.3, along with stringing it also tests for warping. It has poles of various lengths with diameter difference at the top and bottom. It is a very hard challange for a printer to complete but I have…
FR: Version française d'un modèle payant sur Cults du test “Si vous pouvez lire ceci, régler votre stringing” EN: French Version of "If You Can Read This - Fix Your Stringing" A paying model on Cults
Temp & Stringing tower for 0.3 layer, most of the bridging test I found was for 0.2mm layer and when slicing for 0.3mm it wouldn't work, so I designed this to test bridging and stringing, when saving your Gcode name it the temperature you…
Please give it a ❤️ if you like it 🥰 Vous trouverez toutes les infos sur le cache et la manière de nettoyer votre ventilateur de hotend ici : Pour retrouver tout ce que j'utilise : https://kgy.yt/matos Please give it a ❤️ if you like it 🥰
Adhesion: No Support: No Material: PLA Infill: Concentric, 50% Resolution: 0.15mm
Test cones for stringing/retraction with single-layer base.
There are lots of stringing tests available. I just wanted one with a thin base to get results fast. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: .1 mm Infill: 100% Filament: Eryone PLA…
Precise stringing test that can be used for different types of filament.
Quick to print and very cheap while having proper bed adhesion and a stringing distance of about 100mm. Note: If slicer settings like extrusion multiplier or temperature changes don't seem to change much, try using fresh filament or dry…
Painters pyramid or string test! Size small and large! Print head should be at 200 Celsius (if printing with Pla) and bed temperature at around 55-60. Enjoy!
Just print the model and see if you need to fix anything.
I've made these small temperature tower models so they can be printed relatively quickly in about 30 mins. Each model has 9 levels in 5 °C increments and a range of 40 °C. They range from 190-230 °C (suitable for most PLA filaments) to…
Mini design for using little material No support required
Print in the default orientation. Increase retraction speed or distance if there is a lot of stringing.
Minimal Bridging and Stringing Test. Tune your Slicer settings for the best results. Print this testobject in less than 10 minutes.
test stringing 3d printer test torture test
This is a standard stringing test but is faster then most.
You have to print 2 center_parts, 2 side_parts, 1 lever_parts for one flying clamp. Use 60% or more for fill when printing for the strength of the parts. You need additional parts following, 1) a M6 eye-bolt (L=60mm) You can buy it from…
This is a very simple, inexpensive, and fast-to-print stringing test. It takes 3-4 minutes to print with a printing speed of 70 mm/s and a travel speed of 175 mm/s. The gab is about 3 cm wide. As a bonus, here are my retraction settings…
Open your slicer and select your filament profile. Set the print temperature to the lower end of the recommended range. Enable retraction in the printer settings. Set the retraction distance (start with 4–6 mm for Bowden, 1–2 mm for…
A small meaningful stringing test that needs little filament
Summary I needed a quick way to test for stringing when working with new filament. This is the part I devised to fulfil that goal. It's nothing fancy but it's very quick to print and gets the job done. Printing Notes Printed with 0.40mm…
Stringing Test Tower <2 grams 20 minutes 2 perimeters 0% infill
With this model you can test the print quality at various distances and speeds. This model can be printed in less than an hour and uses less than 5 grams. I would appreciate your feedback to help improve the model. Follow me on X for more…
A quick stringing test for your printer thats easy and fast, have fun printing.
What this model tests: Stringing & Retraction: 4 thin corner pins to test nozzle travel, ooze, and stringing. Overhangs & Angled Printing: Side-angled cantilever section to see how well your cooling and overhangs hold up. XYZ Dimensions:…
inTinker's stringing calibration. 4-level.
Purpose of the Model Parametric temp tower for temperature tests, stringing, and bridging. Similar to models by Extrutim and the fixed version of FlorinB . Rebuilt from scratch in FreeCAD 1.1.1. Requirements To create your specific temp…
This is a very simple stringing test you can use to dial in your printer's retraction and other settings. 'Nuff said. Pssssst! Hey this is me from the future. Check out my new Ultimate-er Stringing Test that's like 100 times better than…
A challenging test print to determine how well your settings are to prevent/reduce stringing.
Retraction test stringing calibration - simple bed levelling Are you sure your 3d printer is printing well? Try this retraction test and check the result. It will be ready in a few minutes! It's only 60x20x6.8 mm This is a simple…
![[Flipped] Fast Stringing / Retraction Tests](https://media.printables.com/media/prints/837786/images/6453771_3d35048d-8fed-4942-8f0d-fe2cf30c0954_c924ab62-fc60-48db-91f5-c02c147b34e5/stringing_test_v1_2024-apr-09_11-32-12am-000_customizedview1378487328.png)
