25 modeli
Bring elegance and charm to your space with this stunning 3D printable figurine that captures timeless feminine grace in exquisite detail. This beautiful female figure statue showcases a classic pose with flowing dress and elegant…
TailClippy - the suspender style clip that grips! Print out of NYLON at 0.08mm layer height. assemble with filament
This is brace to constrain movement of suspenders for my chest pouch. It fits 25mm straps and does not disturb my back even with backpack on. Print instructions My print: PLA (Army green & Galaxy silver Prusament) 0.15mm 70% infill 5…
Capture the essence of elegance and youthful charm with this stunning 3D printable STL model that brings artistic beauty to any space. This gracefully posed female figurine showcases exquisite detail in her pleated skirt, flowing hair,…
I made it out of Tough PLA (Bambu) 0.1 layer height, printed in solid pieces. No support needed when printed in Bambu Lab X1 Carbon.
This small gadget helps you not to loose your suspenders. Attention! Only for old people like me - but you need it! And of course its awesome ;-) Print instructions Easy to print, nothing special to do.
The model works nicely for 32mm straps. If you want to scale them make sure that the buttonholes still works. Print in PET-G. I printed with Prusament Galaxy Black on my XL with 0.4nozzle, 0.2 layerhight and 40% infill.
This photo frame came from a desire to hang a number of photos cheaply and to be able to switch photos out from time to time. These are designed to be mounted vertically using Poster Hanging Command Strip so they can be removed cleanly…
I made the switch to suspenders and the pair of Hikers-Uplifters purchased were shorter than expected so i added about 5 to 10 mm worth of length as well as 5mm holes to attach a knife sheath to the hook.
Printed attachment pieces to hang a steel wire from anything you can set a screw in. The wire can be held at place with a m3 bolt and nut. Instructable for the planter can be found at:…
I wear suspenders that have metal clips on the ends. Sometimes the clips break. These hooks slide into the loop of suspender material right at the end of any part of it. They hook onto a belt loop. These hooks are designed for 50mm wide…
My suspender buckel broke so I printed a new one. PETG, 100% infill.
This is not a sexy button. This is not a button that will make you say “Wow, I gotta print this button.” Instead, this is a button that Just Works™. In fact, if you're using this button properly, no one will ever even see it. Several…
Replace your sharp or broken metal suspender buckles with this plastic hook. Perfect if your original buckle is tearing up your car seats or if it has snapped and you need a quick fix to avoid standing with your pants at your ankles and…
2 half clamps fits into the grove of an 8" expansion tank. It has 4 holes (2 on each half) for suspension strings.
Replacement for 1mm diameter shelf suspender/stop. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Fervi PLA Blue Notes: Nozzle 0.4 How I Designed This…
This is a wall-mounted suspenders hook designed to work with standard clip-style suspenders. Instead of forcing the clips over a thick bar, this design uses open slots so the clips attach naturally without excessive stress on the plastic…
I use this on a delta flyer legacy with reused broccoli rubber bands (thick, blue, stiff). Since this is such a tiny delta, it hovers about 100mm above the effector plate, and the bowden between the hotend and the extruder bottom is…
My suspender usually die from loosing this little rubber insert of the clip Print time ca 6 minutes Remove the little crimped tab from the clip if still there insert the new insert and wiggle the little pin on the back trough the hole…
I have made this part to make it easier to have the complete drysuit hanging above the ground. The finnished model was printed in ASA, i'm sure that pteg and ABS will just as usefull.
Made with black PLA. With quite high speed. No problems appeared. Made the model by myself. Worked with a real picture in Photoshop, saved as PNG then converted to STL and added it to the frame in blender. I will be glad to get some…
