34 modeli
Added magnet holes. Magnet holes have square bridges for better bridging and no droopy rings. Printed at low resolution with: PLA+ 0.6mm Nozzle .28 Layer Height High speed No Ironing
Brick | Block 1 x 8 This set of building pieces has been developed through reverse engineering and is compatible with LEGO® building systems. Please note that this project is entirely independent and is not endorsed, sponsored, or…
Gridfinity holder for a 12 in / 30 cm ruler, a wide chisel-tip Sharpie, and 4 other pens/markers/etc. The smaller holes were tested to fit standard Sharpies, Fine Tip Sharpies, X-Acto knives, and Pilot G2 Gel Writer ballpoint pens. Most…
Fits a 1"x8" nominal board to mount the Hadley onto a wood frame without having to cut a semi-circle. Fits an actual board of 0.75"x7.25". Use 3 #10-24 screws to lock in place, need about 1.5" length. Note, this is the first version, will…
A handy solution for your rulers. It's not fancy, just practical. Holds up to four rulers, max size 37.5cm*2.5mm. Be aware that it won't fit on your regular sized (MK3/MK4) print beds. I have included a pre-cut version with dowels. Needs…
You can store nine Plus4 nozzles in this small Gridfinity-compatible (1x1x8) case with a lid. If you combine it with the specially designed intra-chamber Gridfinity base plate for QIDI Plus4, it stores the nozzles in the dead space of…
Three different Gridfinity 1x1x8U Tool Holders: Precision Screwdrivers Needle Files Hobby Knife and Scales Update 12/30/23: Added a version with two 16mm holes for some larger tools I had. Also, added a Block with no holes for easy…
A simple 1x1x8 bin, that holds up to 6 CF-Cards upright (which just happen to fit in a 1x1 bin). Designed 8u tall, so that this bin is still stackable, unlike other CF-bins I've seen so far. adjusted for max number of cards per bin.
I wanted a simple monitor stand, but there was nothing I could readily buy that was long enough for my needs. So I got some nice 1x8 lumber, cut it to the length I liked, stained and finished it, and put on these simple 3D printed legs. I…
larger Infinity for slim, long objekts
Summary A tall, brick‑pattern Duplo wall segment sized 1×8 studs. Designed for clean prints and strong structure without any infill. Compatibility Fully compatible with standard Duplo studs and wall elements. Print Layer Height : 0.2mm or…
An 8 Gridfinity-units high box for holding all the most common button cells (at least, my most common) I printed this up after trying a couple of the others, and was a from-scratch re-write using some of my own gridfinity assets from my…
Disclaimer: This design is an independent creation and is not affiliated with, authorized by, or endorsed by the LEGO Group. It is designed to be compatible with standard building blocks. This brick corresponds to the LEGO brick…
This fits a little tight on a Lab Rax, but maximizes space in the faceplate. The outer walls of the first and last tile do not print, but snaps still fit great in my experience. Created openGrid tiles with perplexinglabs' generator, and…
Summary Build an entire house, tower or skycraper - with this easy-print footing, floor and roof for Brick Walls (1x8)! Compatibility Fully compatible with standard Duplo studs and wall elements. Base dimensions are 9×9 studs. Above all,…
Eine kleine Box für Kreidestücke von einer größe 1x8cm.
Fully working 3D printed amp cabinet. Designed for 8" speaker of your choice. Tested with Celestion eight 15 20W @4ohms. Designed with angled speaker placement for better monitoring. Back panels are mounted by velro so you can customize…
I've started printing the Honeycomb Storage Wall and wanted a tray specifically to hold the cases I have for my rechargeable AA and AAA batteries. I didn't find anything that fit like I wanted so I made my own. There are countersunk holes…
WARNING! Can get very hot with prolonged use I would suggest to print it like in the photo as otherwise I had adhesion problems. Shaving the groove for the camera wire on the back can make the mount centered if it isn't.
Motor terminal block cover 81x81
A simple dispenser designed for standard rolls of 50 Canadian Permanent stamps (approximately 36 mm outer diameter × 24 mm inner diameter × 29 mm wide). It is Gridfinity compatible (available in 1x1x7 and 1x1x8) and requires no supports…
Abmessung: 41,5x41,5x59,8 Filament: PLA Perimeter: 4 Düsen-Ø: 0,6 Infil: 15% Druckprofil: 0.20mm Balanced Filament-Bedarf: ca. 59 gr. Für Entgrater in Sechskantform Fertig-Innenmaß der Sechskant-Form ca. 13mm Aufnahme für 12…
I found Xavierly's set of Gridfinity battery holders really cool, but i wanted to stack baseplates and other things larger than 1x1 on top of them, so i made the height of the AAA holder (was 7U) to match the height of the AA (8U). So i…
A mounting system for a 1x8 board castle for the Nilus Leclerc looms. Each side consists of a a half bracket and half mount plate. These screw together with m3 button head screws (but you can use other 3mm screws if you want) and sit on…
I made this to hold a remote for the Silverstone LSB02-E I got as a review sample. I made it so you can mount it with standard drywall/wood screws, 10mm diameter round 3mm thick magnets, or just double side tape it. I imagine this will…
Upgrade old-building (Altbau) light switches to smart home compatible switches without drilling or screws. This friction-fit adapter fits over 81x81mm standard old-style light switches. It allows you to mount wireless smart switches…
Fully working 3D printed amp cabinet. Designed for 8" speaker of your choice. Tested with Celestion eight 15 20W @4ohms. Designed with angled speaker placement for better monitoring. Back panels are mounted by velro so you can customize…
I found Xavierly's set of Gridfinity battery holders really cool, but i wanted to stack baseplates and other things larger than 1x1 on top of them, so i made the height of the AAA holder (was 7U) to match the height of the AA (8U). So i…
A holder for a 30 cm ruler (total length of ruler is 33,2 cm). It's easy to grab the ruler and to put it back.
Gridfinity holder for single pen (~1cm pen), made for uni-ball eye (ub-150). 1x1x8 with magnets
