88 modeli
This cover is located on the top edge of the tailgate door trim on Mercedes-Benz W124 estate/wagon/kombi models. The plastic gets brittle with age and the latches brake off. I've printed mine from PETG to allow the part to flex a little.…
Wydruk około 0,36 €–0,44 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A battery holder/storage for 10 CR2477 batteries.
Wydruk około 0,87 €–1,07 € nettoWstępna wycena jednego wariantu
*I thought the MK3/4 were 250mm in height similar to most other printers in that size category, I will be working to add a version that fits the 210mm height build volume of those printers Scaled down to fit the bed of a standard 250mm…
This model is compatible with the lego system.
This model is compatible with the lego system.
Half-height beer crate style containers for CR2032 and CR2477 coin cell batteries. Can be used separately or stacked after gluing the stacking piece to the bottom. The CR2032 container can fit 28 batteries while the other one should fit…
Thanks Aiden http://www.thingiverse.com/deadpooleo/about for requesting this conversion. It looks like an awesome addition to the Halo series props. I hope the files work well in your endeavour to print. In time I may have to give this…
Use ASA,ABS, PA6 , print with support easy installation with direct taping screws 2.5mm diameter and 3.5mm screws or epoxy glue
This is a complete rebuild of the 145 ft Steel Arched Truss Bridge by kabrumble. I also added rivets to the plates and added inside plates that print separately. All of the sections needed to be resized to create the proper arch. Also the…
This model is compatible with the lego system.
Lose A Brick? Lose your LEGO blaster or just want another? Than print one. This takes less than 1g of filament and only a few minutes. Print Settings Supports - Yes Infill - 100% (It Doesn't Really Matter) Positioning - Recommend laying…
This model is compatible with the lego system.
This model is compatible with the lego system.
LEGO Panzerwagen Sd kfz 247
multi use inlays for milwaukee slim packout: drill holder 1/4" bit holder low + high SDS-drill holder jigsaw blades
This model is compatible with the lego system.
Tips: for few first layers reduce printing speed to about 60% directly on printer, that gave me consistent results and didn't tear or smear filament (could be some non clean spots on printing surface, so clean carefully before printing)
Vesa adapter plate for Acer G247HYU. Uses the metal bracket from the original stand that clips into the bottom of the monitor. No extra hardware needed. Use the screws that normally hold the tilt mechanism to fasten the bracket to the…
This is a solder-free AirTag CR2477 adapter. The CR2477 battery has about four times the capacity of the standard CR2032 used in AirTags, giving you roughly 4 years of battery life. Anyway, it turns out that at the right angle, you can…
Case 2470 Tractor - 1:16th Scale Uses M4 & M2 Screws Uses Chunky Crab Planetary Rims and Tires (See other models from us)
Blende für Türgriff, Innenseite vorne und hinten für die Fahrzeuge: Links: OEM 321 837 247 Rechts: OEM 321 837 248 Golf 2 (1983-1992) Golf 2 Syncro (1986-1991) Jetta 2 (1983-1992) Passat 32b / 33b (1980-1988) Polo 86C (1981-1994) T4…
Use these files for the carbon fiber beam by Mellow / 247printing: https://s.click.aliexpress.com/e/_DEsgqyl (Affiliate link) Print according to Voron specified print settings. ZIP contains STEP and STL files oriented for printing.…
Adapter to replace button cells batteries with AA or something similar. I used wire wrapped around the outside and some scrap nickel strip through the middle. I soldiered on a AA battery holder and now my wireless sensors have tons of…
Slice at 0.20mm layer height in your favorite slicer with your settings. Feel free to try and tweak your settings for best performance!
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
My interpretation of Alberts amazing 247. I tried to stay as close as possible to his design, but as a matter of fact I am just using the lower fences in an unmodified form. And not all of them. No matter what, credits go to him. This…
GEARS for plotter Hp t920 T372473 B3
1x1 Gridfinity Refined Battery Holder for 5 CR2477 batteries. This battery is typical packaged in quantity 5. Two versions are included, one with the label embedded, to be printed same color or by swapping filament at the end of print to…
Gridfinity 4x CR2477 Coin Battery
Part of my solar shed scale model, this is a mockup of the Watts 24/7 PV Combiner Box used to combine 6 parallel PV inputs to 1 output. https://watts247.com/product/solar-panel-combiner-box-6-circuits-to-1/ The downside of the inverter…
This 3D print model is a 1x1 Gridfinity-compatible battery holder designed specifically to store four CR2477 coin cell batteries . It features snug circular compartments that keep the batteries securely in place while allowing easy…
This model is compatible with the lego system.
museo-nazionale-romano-palazzo-massimo-2474-relief-4 Category: Sculptures
This box is for storing 20 CR2477N batteries. To print without support. If it does not close properly after printing, the inside of the lid can be lightly sanded. Or smear the inside of the lid with candle wax. This ensures that it opens…
I changed the design of TJDesign's “Wera 05” mount to fit the 247 Single-pole phase tester from Wera. The hook is unchanged from the remix of septillion's remix, because i liked it more than the original.
A bigger battery cover for fitting a larger CR2477 battery instead of a CR2450 battery. Category: Electronics
THIS FRIDGE IS MONITORED BY 247CCTV MADE BY MATT GERMAN 200MM X151MM X 3.5MM ,0.3 LAYER HIGHT ,100% INFILL ,WALLS X2 0.8
This part fits the Gridfinity system Gridfinity base sizes: 1x5x1
Doporučuji tisknout s 6 perimetry - kvůli pevnosti - a materiál PC nebo něco podobného, co odolá vyšším teplotám.
The cables can either be glued into the slots or fixed in place by carefully melting them with a soldering iron. Print Settings Printer Brand: Creality Printer: Ender-3 V3 SE Supports: Yes Resolution: 0.2mm Category: Electronics
I have Ruuvitag in every room of the house measuring and storing temperature and humidity. I also have several outside in the yard and several in my 3d printers measuring chamber temps etc. I try to always have CR2477 in stock, but…
Playmobil Durchbruch 30247810 Ritterburg 3268 Mauerdurchburch ersatzeil ich habs in Pla Gray gedruckt. und Super!!
Stackable Gridfinity bin for 5 CR2477 batteries
Wheel for vaccum cleaner ETA 2471
As the Hailo trashbin didn't offer Lids, i created one by myself. This is useful, for instance if you store organic waste in your trashbin. It is compatible with those 7 Liter compartements: Articlenumbers: 1082479 and 1068909 Those bins…
This is a spare part for the pt 24/7, which broke on my airsoft.
10 slot CR2477X Battery Organizer
The battery in my Ecobee smart sensor died and I didn't want to buy a CR2477 battery since I had a ton of cheap CR2032 batteries from other projects. Printer settings: PETG 20% infill 2 perimeters
Nie wieder verlegte Knopfzellen! Dieser kompakte 1x2-Bin wurde speziell zur Aufbewahrung von CR2477-Batterien entwickelt und fügt sich nahtlos in dein Gridfinity-System ein. 🔧 Eigenschaften: Kompatibel mit dem offenen Gridfinity-Standard…
This design exists to take the load off of the stepper motors so that the weight of the X-axis is always supported. It also acts as a 90° support for the Z-axis and will keep the lead screw parallel with the Z-axis if properly assembled…
I didn't find a good and tight mounting system for US standard peg board so I made one. Description: This would fit US standard peg boards with ¼ to 9/32 inch hole and 1 inch hole spacing from center of hole. The bracket has some…
Very simple CR2477 to CR2430 adapter. Print Settings Printer: Bambu Lab P1P Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Any PLA Any Category: Electronics
This is a WIP. This print will add a faceplate to a Arris DG2470 Cable modem so you can rack mount it. It has a window so you can still see the LEDs on the front of the cable modem. This will be my first upload and first functional 3D…
ORGANIZZATORE GT247 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2 / X3 PLUS
This box is for storing 10 CR2477N/CR2477 batteries
I wanted a battery holder that I could place in a storage box and not worry that the batteries would fall out if the storage box tipped. I designed this simple holder with spring loaded sides holding each battery.
This adapter allows you to use CR2032 cell batteries in devices that requires a CR2477 battery. Added a small cutout to make removing the battery easier.
Mr Fox has a KaKu (klikaanklikuit) remote control with a hard to source CR2477 lithium coin cell. Designed a simple adapter for a (thinner) CR2450 cell, filling the gap. This remote control has both contacts at bottom. In case one of the…
Sharp drawer microwaves are known to have an acquired issue where either abrasions on the metal wheel axels or paint damage on the drawer frame from the wheels or wheel axels creates severe current arcing in the microwave. Sharp denies…
Spare part for mounting the cover of GROHE wall connection elbows in the shower. The clip of the original part breaks easily and the part cannot be purchased separately. Therefore, in such cases, the entire wall connection elbow must be…
Friend.Tech 3D printable fan art merch designed and printed by by sonyx.eth : linktr.ee/3esign // https://friend.tech/sonyxeth // https://www.friend.tech/clubs/177915 // https://www.friend.tech/clubs/171788 //…
Not a great fit, but it works fairly well. Print however you want, doesn't have to be too precise cause the design sure isn't. Category: Office
Hallo, es handelt sich hierbei um eine Montiormount um einen Dell Optiplex 7060, oder einen mit gleiche Maßen, an einem Acer b247 Monitor anzubringen. Dazu werden einfach die Gummihalter auf der Rückseite entfernt und die Mount dort…
--- for english please scroll down--- --- moved from MyMiniFactory --- Das Raidsonic ICY Box IB-247-C31 Festplattengehäuse ist hochwertig und bietet eine flotte und stabile USB-C-Verbindung, aber es nimmt nur SATA-Platten mit maximal…
Printed with supports, Simple Battery Holder for CR2477N battery's
Combining this adapter with a wooden plate and feet makes the monitor less wobbly. In addition, the keyboard can be pushed under the monitor when not in use to create more space on the table. Personally i use this with a 16mm wooden plate…
Simple Yellowtec Mika YT3247 Plastic Sleeve replacement If it printed as intended, it should fit with pressure, but you should still be able to remove it fairly easy. I would still recommend the original ones. But if you need to replace a…
BOM 8mm wide nickel strip CR2477 battery printed parts Be careful not to short the battery with the nickel strips and align the positive contact. Screw in lid is left hand thread!
Reinforced wheel and shaft design for the dishwasher basket . Suitable for the Balay V4595/15, Siemens SMS2022-01 and other Bosch Group models (Balay, Bosch, Neff, Siemens). Immerse in acetone for a few seconds to seal the pores and…
Technic Driving Ring 2L 2473
I recently purchased a pre-assembled Geiger counter kit from Electronics Goldmine and noticed that they didn't have an option for a housing for it. So I thought it would be a fun Tinkercad project. This is a simple rectangular box with a…
The VEVOR HR2472 only provides 2 of these fittings. To join all the shelves together, more fittings are required. 4 x M6 bolts and 4 x M6 nuts are required.
It was made for Makita HR2470. The shallower hole is meant to be filled with hot glue (the idea is to be overfilled a bit so the tip of the glue is the point that contacts the surface, so no mark is left there )
Holds 2x CR2477 batteries, with some misc storage space.
Replacement gear with part code >POM< T372473 B3 designed for HP DesignJet large-format plotters (specifically tested/adjusted for the T7920 , and compatible with the T920 / T1500 / T2500 series). About this Remix: This model is a…
multi use inlays for milwaukee slim packout: drill holder 1/4" bit holder low + high SDS-drill holder jigsaw blades
I have Ruuvitag in every room of the house measuring and storing temperature and humidity. I also have several outside in the yard and several in my 3d printers measuring chamber temps etc. I try to always have CR2477 in stock, but…
This is a solder-free AirTag CR2477 adapter. The CR2477 battery has about four times the capacity of the standard CR2032 used in AirTags, giving you roughly 4 years of battery life. Anyway, it turns out that at the right angle, you can…
Print notes: Print vertically (threads upright) Enable light supports between threads only Brim recommended 5 walls / perimeters 20–40% infill PETG or ABS recommended
Half-height beer crate style containers for CR2032 and CR2477 coin cell batteries. Can be used separately or stacked after gluing the stacking piece to the bottom. The CR2032 container can fit 28 batteries while the other one should fit…
This model is compatible with the lego system.
Before you go further! This model is available for free for all my supporters in Printables Club 🧡 Consider joining my club to have access to all ⭐⭐⭐ exclusive projects ⭐⭐⭐ and be part of my community! This project is for personal use…
Print notes: Print vertically (threads upright) Enable light supports between threads only Brim recommended 5 walls / perimeters 20–40% infill PETG or ABS recommended
Simple Yellowtec Mika YT3247 Plastic Sleeve replacement If it printed as intended, it should fit with pressure, but you should still be able to remove it fairly easy. I would still recommend the original ones. But if you need to replace a…
