Liczymy pasujące modele…
A pluggable battery holder that allows you to fly your BetaFPV Air 65 with bigger battery packs like 450mah / 550mah or any battery pack of 17mm of width. Optionally use a M2 screw to secure it to the frame. Sources available!
Print in TPU. Fits 1s 450-750 batteries.
A sleeve that will clip on to the 300mah Meteor65 battery sleeve, will allow you to use 450mah. I printed it on it's end with the clip opening facing upwards at 15mm's without supports. It's a tight fit to clip it on the 300mah sleeve,…
What? A transport box for 1s 450mAh Betafpv lipos It's really tight, so you need a good calibrated printer, otherwise print it with 101% size. Why? I was annoyed that the batteries were flying around in the bag all the time. How? I…
Cut the original battery holder parts off so that you have two parallel and flush rails which the battery holder clips into. print in TPU
I slightly adjusted the dimensions of the 420mah battery holder to make one more suited for a typically sized 450mah. The walls are a bit thinner than the original battery holder so it is easier to install if you have a battery in it.
Mobula 7 Battery Shim for when using a battery that's too thin like the WeBleedFPV folded 450mAH batteries or 300mAH batteries Print flat on the bed with supports (see pics). 100% infill Category: R/C Vehicles
A remix of fuspy's remix of gsatelite battery holder. This one now fits BetaFPV 450mAh 1S LiPos. (and anything else you manage to force into. * cough * GNB 380mAh 🙈) Recommend printing in TPU or something similar. If you've come this far…
A LiPo battery holder for BetaFPVs Lava 3S packs used by their Pavo20 series. Or any other thing with a rectangular profile measuring around 20mm x 15,5mm. Small holes at the bottom help with releasing pressure in case of a tight fit.…
As all the other battery holders did not seem to work for me I made my own. V1: has hooks to hold on to the frame. V2: slides ove the frame so won't pull off in a crash.
This fits between the 2 battery holder bars of the Mobula7 frame, put the longer side in first and then squish and pop the other side in. This also fits the Beta75pro frame if you cut off the existing battery holder trimming it flush and…
Remix of the referenced battery holder
Holds 2S 450 mAh LiPo FPV drone batteries securely in a lightweight TPU (or PP) frame. Available in 2, 4, 6, 8, 10, and 12-slot versions. Designed for single-wall printing with a 0.8 mm nozzle, but also prints well with a 0.4 mm nozzle.…
This is a LiPo battery protector/bumper. After puncturing a battery during a crash (dangerous stuff) I tried finding a suitable protector for my batteries, but I couldn't find one. This will fit a CNHL MiniStar 450mAh 4S LiPo battery, but…
Slim Battery Case for 5 450mAh 550mAh Drone Batteries
So I needed a way to carry my tinywhoop, and I really liked the U.S. General gridfinity setup that Uncle Jessy showed off. This is just one of the bins that I made for my system.
This simple model of holder are use on Tattu 450mah (Dimension : 63*17,5*7,1 mm) who give and additionnal minute to fly compare to lavaII 320mah (AIR65 CHAMP). Printed with tpu and less than a gram (.39g)
Microsquad Watermelon „1S HV 450mAH Schubkraft“ Dummy Print Settings Printer Brand: Creality Printer: Ender 2 Rafts: No Supports: No Resolution: 0,15 Infill: 20% Filament: dasfilament.de PET-G Category: Other
As I want to run my Tamtech 1/24th Ferrari Testarossa, I have removed all the stock electronics and am replacing them with updated kit. This sled will fit the Turnigy Nano-Tech 450mAh 2S LiPo (and smaller) batteries - there's a bit of…
Made one that fits 450mah batteries
450mah (7x17mm) 1S battery mount for FlexRC Nano X drone. Print in TPU, no support. Also check out my camera mount! Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill: 15% Category: R/C…
Following advice on transporting LiPo batteries, I have kept the original boxes they arrived in, but with the protective cover installed on the balance port, the batteries do not fit well in the original insert. I do not want the…
As all the other battery holders did not seem to work for me I made my own. V1: has hooks to hold on to the frame. V2: slides ove the frame so won't pull off in a crash.
This is a mount to slide your 2S pack onto the TC-18. The rubber pad has do be applied to keep them firm in place. Watch it in my short showcase
Hexagonal Battery Case for 5,7,8 450mAh 550mAh Drone Batteries
This simple model of holder are use on Tattu 450mah (Dimension : 63*17,5*7,1 mm) who give and additionnal minute to fly compare to lavaII 320mah (AIR65 CHAMP). Printed with tpu and less than a gram (.39g)
This is a LiPo battery protector/bumper. After puncturing a battery during a crash (dangerous stuff) I tried finding a suitable protector for my batteries, but I couldn't find one. This will fit a CNHL MiniStar 450mAh 4S LiPo battery, but…
Battery Holder for 450mAh sized batteries. Holds 4 or 8 batteries. Case allows for both vertical and horizonal orientation. I usually store Vertically for Charged batteries, and horizontal for discharged batteries. Originally printed with…
This is a mount to slide your 2S pack onto the TC-18. The rubber pad has do be applied to keep them firm in place. Watch it in my short showcase
Hexagonal Battery Case for 5,7,8 450mAh 550mAh Drone Batteries
This case comes in three versions: three 450mah and three 550mah batteries, six 450mah batteries or six 550mah batteries. the dimensions fit perfectly for gnb lipos but other ones from BetaFpv etc. should be fine too. I printed this case…
