Liczymy pasujące modele…
I have a BitAxe Gamma running and the downside is that these can get quite hot with the stock cooler and fan. I got numbers running up to 65-70 degrees celsius without overclocking it. I was limited to 595MHz by 1.15 volt. After the…
I wanted to put my 52Pi ICE Tower Cooling Fan on my Raspberr pi 5 but the brackets were incompatible due to the PoE header. So I made my own. The 52Pi ICE Tower Cooling Fan was originally made for the Raspberry pi 4, but these brackets…
I use a Raspberry Pi 5 as a media player when travelling, so I needed a way to power it from a 12 volt power source while off grid. I chose the 52Pi PD power expansion board as it allows you to power a Raspberry Pi 5 utilising 9-24v input…
UNTESTED !!! This version is intended to be used with: https://52pi.com/products/52pi-ultra-thin-ice-tower-cooler-cooling-fan-for-raspberry-pi-4-model-b-cpu-fan it was draw and corrected based on this version:…
This version is intended to be used with: https://52pi.com/products/52pi-ultra-thin-ice-tower-cooler-cooling-fan-for-raspberry-pi-4-model-b-cpu-fan it was draw and corrected based on this version:…
The cooler has strange geometric parameters and a fan in an unusual size of 50x50mm. The fan has a 3-pin connection and is quite noisy. In order to operate a quiet Noctua A6x15 or A6x25, an adapter had to be created that could be attached…
I wanted to put my 52Pi ICE Tower Cooling Fan on my Raspberr pi 5 but the brackets were incompatible due to the PoE header. So I made my own. The 52Pi ICE Tower Cooling Fan was originally made for the Raspberry pi 4, but these brackets…
I carelessly printed and struggled to fit the display case that I have remixed here, not noticing until I had ripped the OSD rocker switch off, that my display was not the one for which that case was designed. I therefore had to model…
My Geeekpi display case requires at least a desktop stand, since the feet supplied with the display do not fit once the case is installed. I happen to have a section of Honeycomb Storage Wall (HSW) installed along the front of my printer…
Mounting bracket for 52PI ICE Tower on the Bitaxe suited for pcb models 40x and 60x Print with filament that has a high heat tolerance, personally i print with PC. Print with brim to prevent warping and/or print in enclosure. Print upside…
Fan cover and shroud for 52PI Low Profile Plus for Bitaxe. Print with PLA
Who has 2.5mm Cap Hat screws lying around? Well, I don't! So I modified this awesome design from Jeepers01 to be a little (0.7mm) deeper on the inside so that the Pi with the NVDAC can fit and the connectors align properly. The downside…
Mounting bracket for 52PI low-profile plus on the Bitaxe suited for pcb models 40x and 60x Print with filament that has a high heat tolerance, personally i print with PC. Print with brim to prevent warping and/or print in enclosure. Print…
No additional hardware is needed other than what is provided with the cooler. Printed at 95%(100%) infill with eSun PLA+. The standoffs do not need to make contact with the PCB. Do not over-tighten. Use high quality thermal paste. The CM4…
Re-designed to take the 52PI NVME & HDMI board. Two alternative lids, both designed to take a NOCTUA 5v 50mm or 60mm fan. The header plug allows the fan header connector to pass through the case but be sealed and hidden by the plug. A…
I've made this model because I was unable to find a case that was exactly made for this addon. I also made it able to fit an SD card if its necessary. The middle part is sandwiched between the Pi and the NVME bottom. The example in the…
Choose the lid you want from the original model (with or without gap for heatsink): https://www.printables.com/model/127621-raspberry-pi-4-snapfit-case-geekworm-x857-ssd-boar/files https://wiki.52pi.com/EP-0171
a remix of the rpi5 case with space for the pimeroni nvme base. but adapted for use with the 52pi ultra thin ICE cooler. it now has vents on the side for better cooling with the 52pi ultra thin ICE tower cooler. Also did a small tweak on…
The TOP case is developed in 2 parts due to RCA output. First install both TOP parts with Pi5. Close assembly with BOTTOM part. I printed in PLA at 0.1mm height and 0.4 nozzle. I think best practice to add some spacers at the bottom, for…
I use a Raspberry Pi 5 as a media player when travelling, so I needed a way to power it from a 12 volt power source while off grid. I chose the 52Pi PD power expansion board as it allows you to power a Raspberry Pi 5 utilising 9-24v input…
I created this set of brackets to hold down the heatsink on my Raspberry Pi 3B+. Originally the heatsink came with adhesive tape but never really held on too good. When I replaces the tape with silicone pads the heatsink kept falling off.…
Raspberry Pi5 PCIE NVMe Case for 52Pi NVDAC HAT The case has been designed to house the 52Pi PCIe NVDAC HAT audio expansion board mounted over the Pi 5 Active Cooler above the Pi 5. The 52Pi hardware kit includes 4x M2.5 x 17 Brass…
