Wyniki wyszukiwania: 9305

Sortowanie

Liczymy pasujące modele…

P
Printablesthall72

Lego Compatible (93055.dat) Minifig Sword Katana (Dragon Guard)

This model is compatible with the lego system.

Pobrania
448
Polubienia
71
Ocena
0
P
PrintablesFireTime

LSI 9305-16/24i fan shroud

LSI 9305-16i or LSI 9305-24i fan shroud. This is a remixed design from barichardson with most overhangs removed to be more easily printed. Snaps onto the heat sink without the use of screws. Four STL files for both the 16i and 24i with…

Pobrania
446
Polubienia
24
Ocena
5
P
Printablesthall72

Lego Compatible (93059.dat) Minifig Hat Conical Asian

This model is compatible with the lego system.

Pobrania
269
Polubienia
44
Ocena
0
P
Printablesthall72
Pobrania
207
Polubienia
38
Ocena
0
P
Printablesmgrobins

LSI 9305-16i Fan Shroud for 60mm fan.

I printed this on its side with only necessary support. I'm not sure which is best for it. The fit is excellent. Be very careful with the clip on the heatsink as the heatsink is not rigidly mounted and the chip on the PCB has no metal…

Pobrania
122
Polubienia
8
Ocena
4
P
PrintablesJustPrinting

LSI 9305 16i 40mm Fan Shroud

40mm Noctua Fan cooles 9305 an air geht's exhausted out the back. Mounts wit zip tie to card.

Pobrania
53
Polubienia
7
Ocena
0
P
PrintablesTJ_Makes

LSI 9305-16i fan shroud (6mm)

Remix of the original 16i fan shroud to fit a 6mm thick fan. Was done to make it as low profile as possible. link to the fan: https://www.mouser.com/ProductDetail/ADDA/AD0412HX-K96XT1?qs=vmHwEFxEFR%252B%252BE%2FX1PRFofA%3D%3D

Pobrania
42
Polubienia
4
Ocena
0
P
Printablessrc

Ceiling Fan Remote Battery Cover KUJ9305

Replacement battery cover for a ceiling fan remote, FCC ID KUJ9305. The new part is 45.7mm wide, 56mm long, 2.15mm high Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .2 Infill: n/a Filament:…

Pobrania
17
Polubienia
0
Ocena
0
P
Printablesdaktah

LSI 9305-16e Fan Shroud (40mm)

Intended to be printed upside down as shown. Supports recommended. PLA or PETG recommended as you need to stretch it a bit to install. No special print settings needed. Requires 4x M3 screws and 4x M3 nuts. Screws need to be the thickness…

Pobrania
7
Polubienia
0
Ocena
0
P
Printablesinfintus

LSI 9305-16i 50mm Blower Fan Shroud

I really wanted to slim this design down and fit it in my case, so I used a blower fan design instead of a traditional fan to leave room for the front panel headers on the motherboard. This takes up less than a full width PCIe slot as…

Pobrania
0
Polubienia
0
Ocena
0
P
Printables

LSI 9305 16i 40mm Fan Shroud

40mm Noctua Fan cooles 9305 an air geht's exhausted out the back. Mounts wit zip tie to card.