Liczymy pasujące modele…
Purpose: These models were created in the hopes to make it easier for a wide variety of people with varying disabilities to utilize an Xbox controller in a way that may be easier for them. I personally have been paralyzed for a long time,…
Habe ein paar Teile gemacht, um für meinen Mobula 8 ein Walksnail Avtar mini 1s zu adaptieren. Der Mobula kam mit dem Frame für das DJI O3 light, ich wollte das aber mit dem Mini 1s von Walksnail ausrüsten. Nach einem ersten Versuch mit…
This Remix is more of a QoL improvement than a major change. I may update this with additional changes as I use the toolhead. Hardware Required: 4x M3 D5 L5 heat set inserts (L4 inserts will also work, use less torque) 2x M3 D5 L4 heat…
I printed everything from the original post and tried to build the boat. In general it works well only some parts like the Rudder and the engine makes me some trouble. So I ordered several other parts instead of the listed ones. Following…
These models allow you to 3D print some mounts for NEMA 17 motors for your Unimat 3 lathe. I've then added 48 tooth GT2 pulleys to the NEMA and the Unimat leadscrews which both have 5mm diameter mounts. I then used a closed loop GT2 belt…
Made some changes to use sawblades with 16mm hole. Had to raise the base 5mm ans addes different on/of switch (round) and other power inlet (round), moved the hole for the sawblade, adapted motor-mount-part-1 and made the rulerpart a bit…
Fits all SR20 Heads, although later S15 heads had different sized holes so the Yaris coils don't seat as well. Please print out of carbon fiber nylon or ABS due to temperatures in head. 1 version has cable ties 1 not, i printed 2 of each…
Since the shape of the Nuovva cereal container deviates from the original design, several modifications were necessary: Container geometry : Front side is narrower → front axle shortened by 10 mm. Axle holders : Introduced a 5 mm offset…
This is a remix of several parts to mount a Hemera on a Voron Switchwire. I have abandonded this project and preset it as is. There will be no further changes. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament:…
For mounting the Unifi AP-AC lite or Unifi Nano HD to a European type power box/junksjon box. Two of the holes on the unifi plate fit the wall box screws, the spacer plate here is so the Ethernet cable can exit the box and connect to the…
Printable adaption plate the MicroSwissNG Revo for an Ender 6 with BLtouch. Based on the aluminium version of MicroSwiss which is unfortunately missing an BLtouch mount. Use m3 brass inserts for the adaption plate, print using PETG or…
Rather than the short stubby handle, here's one you can print for use with a long broom handle. The hole is 23.2mm, so its for a (you guessed it) 23mm diameter broom handle with a .2mm clearence. There's also a hole in the back of it…
Adding a cylindrical portion without increasing the overall height to increase printability.
My Drill Press was made to hold older style hand drill not a Dremel. I wanted and needed way to mount Dremel rotary tool on it. Thanks to 3D printer I was able to make a trihole clamp to mount my Dremel to it. I made an adapter plate that…
Remember to tighten the rollers properly, as if they are loose on the bearing, they can easily break. The rollers have a special cutout inside the thread to make them more durable. The Prusa settings I used to print the above set are in…
Note: This file set is an extension to the HomeCube enclosure project. To make use of this file set, you have to download the basic file set and building instructions PDF as well. If you own a Prusa I3 Mk3 (S, S+) equipped with the Bear…
Garden equipment modification of the original Broom holder. The L edition of the grabber fits the original parts and I've had success in fitting tools with a shaft diameter of approximately 24 - 30 mm. The XL edition requires a different…
Deutsche Beschreibung unten My wife asked me to adapt this awesome phone holder for an iPhone Mini. This is the version for an iPhone Mini without a case. After I did that (you can find it here), she also wanted a version for an iPhone…
By printing 5 of these models you can place them in a Louet spinning wheel. I used 3/8" dowels for strong pegs. The length of each wrap on the skein is about 1 yard, 39". I simply detached the foot pedals and hand-wound the bobbin onto…
Printed on CR-6 SE with PETG I added the initial holder so you can design your own mods. It's recommended to design your own ring to fit your arm.
This design was made for my colleagues in our equipment loan department when their new mini dual v-mount chargers (Hawk-Woods VL-MX2) couldn't accept all their v-mount batteries as the mounting positions were too close together by around…
Adaption for WC door lock. From 4x4 to 6.25x6.25.
My wife asked me to adapt this awesome phone holder for an iPhone Mini. This is the version for an iPhone Mini with a case . After I did that, she also wanted a version for an iPhone Mini without a case. For this version (with case) I…
45mm riser for front wheel tire width app. 30mm used it on a canyon ultima with a front tire
Left & Right X-Carriage brackets modified to fit the Zesty Nimble Extruder | https://zesty.tech/ Refer to the original BigBox IDEX Bowden for details | https://www.thingiverse.com/thing:2073946 Print with your favourite thermoplastic |…
Fuel tank ventil adaption
modeling a car is not what i am born for.
This is made to adapt the lcd pi station to fit a raspberry pi 4B. I had the station already printed and then noticed a 4B won't fit. maybe its nice for when you upgrade the PI to a new model. !!! This will still need the main station !!!…
This is a remix of the Makita bit holder with adaptions to: - add a Magnetto magnet - reinforce the holders - lengthen the holders for easier access once the magnet is added. ### Printing suggestions: Print it standing on the bottom end…
Modified the bolt pattern and part fan cooling duct length on the body to account for the additional length.
Microswiss NG fan shroud edits for Duender or any corexy printer using MGN9H rails. For more details see my other post. Two versions: Fan shroud with sensorless homing datum added and stock fans. Fan shroud with sensorless homing datum…
A mantis holster receiver compatible with the tek-lok system or for printable hek loks
This is a remix of the Makita bit holder with adaptions to: - add a Magnetto magnet - reinforce the holders - lengthen the holders for easier access once the magnet is added. ### Printing suggestions: Print it standing on the bottom end…
Remember to tighten the rollers properly, as if they are loose on the bearing, they can easily break. The rollers have a special cutout inside the thread to make them more durable. The Prusa settings I used to print the above set are in…
45mm riser for front wheel tire width app. 30mm used it on a canyon ultima with a front tire
Hex Socket Head adaption for the lid of the case for DiyAudio SMPS DC Filter P089ZB.
