Liczymy pasujące modele…
Designed to fit all the generic 0.28" sized panel-mount modules available online. Extra space in the case is for project wiring. Use 2 M3x12 to attach lid and #6 screws to mount the case. Print lid face down and case back down. Example…
This is still a work in progress! I haven't gotten a chance to actually cut this (waiting on parts/time) yet. Putting it out there anyway. This is a Control Panel for the K40 Mini (the 30w, smaller version) that incorporates a…
I created this mounting bracket to hold two combination volt/ammeters for my portable generator. Each gauge monitors one of the 120v legs of the 240v generator. Print this out in PETG, ASA, or something similar since it will get pretty…
I wanted to replace the old Analogue Voltmeter with a new LED Voltmeter. I designed this frame to mount the new LED voltmeter in a frame that match the old meter looks and dimensions on the face of the PSU. The second version have the LED…
You can buy a wifi power controller to link your solar PV and hot water boiler. However the item as shipped does not provide a way to clamp the power cables, and the cover over the live terminals can be opened by “little fingers”. This…
Notes: don't print the reference combined file uses M3 screw and nut to tighten uses 2 male and 2 female XT90 sparplug look at combined parts for reference use fitting screws to fasten the bracket use shunt that is correct for your…
Requires M3 45mm long bolts to mount to the super simple slide on only DIN rail adapter. Both parts print with no supports. Print the DIN rail on its side, and the case face up. A FreeCAD file has been provided for the DIN rail adapter.…
This is a holder frame to install a popular “Chinese” volt and ammeter gauge with 100V/10A ratings to a Multi-Voltage Regulated DC Power Supply: MW122A. Installation You will need to drill three (3) holes on the MW122A shell, one hole of…
This is a cover to fit a General Electric Analog Ammeter. The dial case slides onto the rear screws and the back cover slips onto the case. The standoffs on the back cover fit a Raspberry Pi Pico. The “Internet Speed” badge can be secured…
Desktop enclosure for the Drok DC 4.5-100V Digital Voltmeter Ammeter Multimeter panel and 50A shunt. There are pegs built into the base to hold the shunt in place without needing screws. There are vent holes in the front to allow some…
volt/amp metre http://www.banggood.com/0_28-Inch-Dual-Display-Red-Blue-LED-Panel-4_5-30V-Digital-Voltmeter-Ammeter-1-100A-p-1093413.html?rmmds=myorder metre used for the heat bed but wanted to combine a few things, trying to stop some…
Cheaper Ammeter / Voltmeter show the PCB on either sides of he display and white edges can be seen when viewed at an angle. Printed a Couple of different types of blacks to cover this up. The first just covers the PCB and does attempts to…
This is the DXF file for the Milliampere Meter Housing for Co2 lasers. The file is made for 6mm plywood, and to get a good fit you would want to use correct kerf compensation, but works with no compensation too. The magnets are 20x7 mm…
The cheap import ammeter on my Farmall 400 tractor finally gave up the ghost and the needle flopped back and forth at the mercy of bumps. I had an original IH 354473R91 meter in the shop that lacked the sheet metal holding clamp. This…
You can assemle it and put it at the top, the side or at the front of your mashine. Category: Hobby
Custom Box for Digital Voltmeter & Ammeter Fast and easy print to add a box to your cheap digital voltmeter and ammeter. For my setup, I used: 2 x M3 screws (6mm or 8mm) 5 x 4mm banana plugs 5 x M4 Binding Post (3 red and 2 black) 20 AWG…
Custom Box for Digital Ammeter Fast and easy print to add a box to your cheap digital ammeter. For my setup, I used: 2 x M3 screws (6mm or 8mm) 4 x 4mm banana plugs 4 x M4 Binding Post (2 red and 2 black) 20 AWG of whatever length you…
Build you own DIY Bluetooth combined voltmeter and ammeter. It communicates via Bluetooth with the phyphox app - a free Physics app from RWTH Aachen University. The device is based around a ESP32 microcontroller board and uses an INA219…
Mr.Jay's EZ-METER is a handy little device that anyone can make. This clever little tool can display both volts and amps simultaneously, as well as being able to run on “dead” 9v batteries. All you need to do is order the parts from the…
I decided for the K40 to mount the 85C1-A analogue ammeter externally, and I needed a case for it. My specific purpose was for the laser, but this will work if you just need an ammeter case for something. This case comes in two parts: a…
A replacement case / sleeve for small digital DC voltmeter ammeter display. I have one of these small digital panel mount displays that only comes in black plastic. I designed a replacement case / sleeve for it so it could be printed in…
Suitable for 85C1 ammeter (64x56mm). A 64x59mm cut to be done prior installation. No screw needed, just push and your are good to go
Created this basic enclosure that utilizes PG7 glands to provide a little nicer looking volt/ammeter for my x-connect. It has enough room to store a 3x6 wago or a 2x4, along with a normal ago to allow you to wire everything together.…
Uses M2.5 screws to hold lid to body Designed for these voltmeter/ammeters: https://amzn.to/3Ziacr5
Case for a 3 lines display, separated with banana plug (5mm) and switch (12mm). Added + and - symbols (not in photo!)
I created this mounting bracket to hold two combination volt/ammeters for my portable generator. Each gauge monitors one of the 120v legs of the 240v generator. Print this out in PETG, ASA, or something similar since it will get pretty…
Housing for a cheap volt-/amperemeter from aliexpress for fischertechnik. Compare the images, there are a couple of similar variants. Note that the ammeter's precision is only 10mA and it will start measuring amperage only from 20mA…
Large ammeter perfect for surface mounting on laser cutter. Meter fits in the housing so can be mounted on top, front, or side of laser engraver. Parametric (Fusion 360) file can change the tilt angle (22.5, 30, or 45 degree).
Halterung für Aideepen DC 50V 5A 250W Digital LCD Voltmeter Ammeter/Powermeter https://www.alibaba.com/product-detail/Aideepen-DC-50V-5A-250W-Digital_1600587970085.html for fitting into top viewed battery department - for devices that are…
![[ Laser Cut ] Milliampere meter (Ammeter) housing for Co2 laser.](https://media.printables.com/media/prints/199222/images/1838008_df624d68-68ec-44fd-b24b-6c6b126e6bdc/dsc_0350_s.jpg)
