Liczymy pasujące modele…
This is a wallmount for the Ubiquiti UNAS2. It has a perforated bottom for ventilation and a hole to route the network cable The mounting holes are designed for M3 countersunk screws. Overall it has a snug fit and offers enough resistance…
Single and double holder for the Stihl AS 2 Batteries
Because I broke the original servo arm. I made a replacement.
Halterung für 2 Stihl GTA26 Akkus AS2 (28 Wh, 10,8 V ), Öl - Flasche und Ablage für Kette. -------------------------- Holder for 2 Stihl GTA26 batteries AS2 (28 Wh, 10,8 V), oil bottle, and chain storage.
Clip-on thermal imager COTI AN PAS-29 has various modes. Full Heat Mode, Patrol Mode and Contour Mode. It is easy to adapt, and the function is simple and easy to use...Of course, it is just a model and cannot achieve special functions,…
I took Apple watch band holder by as2008schl and merged all of the modular bits in to one 5 slotted holder meant to be mounted with double sided tape. The ones on the left are 42mm and the right are 38mm and both fit nicely. These were…
Hello, If you like the Thing please leave a like. This OSVAC Adaptor is made for my Metabo BAS261 Bandsaw. Maybe the Adapter also Fitts other Metabo Bandsaw Models, please tell in the comments. Category: Parts
Remodeled the original model so that the tip of the Bosch GAS25 vacuum cleaner tube could be connected at once. To join the original finished part "body2" I drilled out the holes with a 2.5mm drill (careful not to drill through) so that…
Two mounting methods. Dos posiciones de montaje.
Redesigned ¼" tripod/accessory adapter for Sony Action Cams. Designed for HDR-AS100, but may also fit HDR-AS200. This adapter replaces the terrible original adapter that only has a single mounting point at the front of the camera. I broke…
took inspiration from : https://www.printables.com/model/1332736-fosi-audio-zk-tb21-amp-frame decided to make one for XY-AS21HPA (TPA3255 AMP)
this case is made to replace a the original case. these are not water proof like the original but that was not the aim. it just gives it a extra layer of protection. and options to mount it on. I have included some Step wiles in case you…
Strong and easy to print. Resistente y fácil de imprimir.
I have progressed beyond this to working on a gimbaled version, but thought someone might want to use these files which I used on my testbed Phantom a couple of months ago. I will post the sequel with a controller when I get it finished.…
[CZ] Hlavní řemen pro promítačku Meoclub 16 AS2 , nebo Meoclub 16 AS3 . [EN] Main belt for the projector Meoclub 16 AS2 or Meoclub 16 AS3 . Filament: Spectrum S-FLEX 90A Resolution: 0.10 mm
The mechanism allowing the case to shut broke, so I design this replacement. Be aware that, I didn't test if it was still water-resistant .
This is a Adapter to mount an Sony Action Cam to a GoPro "3 Finger" mount. You need a M6 Screw to attach the Camera to the Adapter. 2025-03-19: I added a shorter Version where you can open the MicroUSB Port to charge the Camera while…
I printed it with PETG it would be stronger but I think PLA would suffice. mirror the model for the second half.
Ein Schutzrahmen gegen Schmutz und Späne und gegen verstellen des Maschinenzeigers. Als schutzscheibe habe ich ein 1,5mm Plexiglas genommen und den gesamten Rahmen mit Spiegelklebeband angeklebt.
Sometimes I get SAS expanders with only Full-Profile brackets, or I simply forgot to order them... or lose them.
On the rear side of the vacuum cleaner body, there are some plastic supports (see picture). As the electrical cable is long (good point) and there is no place to keep it, I designed a support to wrap it. It is engaged in the body supports…
Gigaset AS285 Holder for Kuepper pegboard. Printed in PETG with a long key holder for sufficient stability. I printed it upright with a few small supports, just to be safe :)
