Liczymy pasujące modele…
Remix of a remix of a remix, I really wanted the replacement to be as similar as possible to the original part, so I added a Beyerdynamic logo and L/R indicators. IMPORTANT: Printed with a 0.25mm nozzle using Prusaslicer 2.5 with Arachne…
Proven working: PLA 0,15 structural Snug supports everywhere (organics do work but are a pain to clean up) Remember to remove supports on the inside
Wanted a hard case to stop my Beyerdynamic DT-770's from getting dinged up in my backpack. The commercially available cases were either too large, or required you to bend the strain relief grommet, which seems to invite problems, so I…
If you know what this part's actually called please tell me, also tell me if this fits any other headphones than the DT 990 PRO, a lot of their parts are compatible with multiple headphones. Beyerdynamic doesn't sell it so I couldn't…
Microphone Holder for a Beyerdynamic Space. Can be installed pretty much everywhere by pulling a velcro strip through the two slits at the back.
Plastic cap (decorative) for Beyerdynamic DT 150 - i can add versions with some decors if you ask :)
Note that replacing the original earpads will significantly alter the sound of the headphones. Aftermarket bass heavy (Beyerdynamic) earpads would be preferred, but even with them the sound would be much different. I created this adapter…
On photo, plate holder wrapped with leather textured vinyl wrap.
A quick project which is a replacement for Beyer's shitty plastic side brackets that attaches the speakers to the aluminum forks. I've had two sets of these break over the years, on two headphones. The plastic crumbles over time and snaps…
Multiple mods exist for the DT770 PRO headphone. So, I made this jig to be able to drill holes accurately in multiple enclosures. Also useful for balance mod where you need to drill both enclosures of the headphone. The jig is parametric,…
This thing solves a very specific problem - when my earcups are in the retracted position (I have a fairly average sized head), if I turn the earcups, the guide will hit the steel headband of the earcups, rubbing against it and making an…
This is a replacement slider mechanism for Beyerdynamic DT 770/880/990 headphones. You will want to print them with the flat side facing down. I printed mine with 3 walls, 25% gyroid infill, NO supports, and a 0.12 layer height. I…
The Beyerdynamic DT48 is a legendary headphone that was introduced in 1937 and remained the same until it was discontinued in 2012. Unfortunately, replacement ear pads are limited. This adapter allows you to use Beyerdynamic DT990 ear…
Allows you to adapt much more comfortable and cheap replacement earpads, in this case, beyerdynamic! (or other 95mm earpads)
Reaplacement part for Beyerdynamic DT 770/880/990 headphones, to be used with original screws. Designed from scratch based on the original ones, intended to be stronger. Recommended settings: PLA at 0.15 or 0.2 layer height, no supports…
With this thing you can rapair your broken protective rubber sleeve on the Beyerdynamic MMX 300 headset cable. You have to print the part twice. To open the earpiece you hav to do a few easy steps. Remove the earpiece cushion, than you…
Slightly modified version of Volans design to make it fit a little bit better and give it slightly more notch-feel. Tested on my DT770 Pro headphones and now they feel exactly the same as the original ones. I printed them with a 0.6mm…
Loudness SPL (dB) Calibrator (AZ 8930 B 13.2mm) adapter for the Beyerdynamic MM 1 (9.5mm) Print with a rubber like material, I used TPU. Make sure to clean the print of any debris or stringing. I calibrated 2 microphones with and without…
The Beyerdynamic ‘Custom One Pro’ headphones let you replace the stock side plates for custom ones. Hence the name, possibly. Made these to have exagerated Left Right markings but the possibilities are endless. Feel free to use this model…
Simple mount that attached to the headphone strap cushion. Holds a bluetooth receiver. Should also be compatible to BeyerDynamic DT770 DT880 DT990 and possibly others. For more see https://xythobuz.de/2021_09_05_dt770_xlr_mod.html Update…
This is a replacement for the DT990 slider housing that I modeled after mine cracked. Beyerdynamic offer a replacement part for sale but I didnt want to pay as it was simple enough to model. Print both sides with the flat face down…
A case for the microphone and the dongel + adapter of the Beyerdynamic MMX 200 Headphone. This case uses 8 6x3mm magnets to hold the top and bottom together. For easy remixing i included the step files. Printed in PolyTerra Carbon Black…
A adapter to strap a ComfortMAX headband to most Beyerdynamic Headphones
An adapter for the Beyerdynamic DT 440 to add the cushions of the DT 770 PRO (https://www.beyerdynamic.de/p/edt-770-v). Adapter clicks in place one the ear cups. Printed without supports in PLA
Versions Two versions of the internal driver support ring are available. One is the standard stock ring as a replacement part. The other is modified with and additional cut-out, this allows it to be used when modifying the DT770s to have…
Since the included ear pads of the MMX200 unfortunately tend to break quite often, I designed an adapter to mount the DT770PRO ear pads onto the MMX200. The adapter consists of two parts: Part 1 attaches to the MMX200. Part 2 holds the…
Pokud se vám model líbí, budu rád za váš like. If you like the model, I would be happy for your like.
A filing jig for use with Calrad 30-711 3.5mm TRS chassis mount snap-in Jacks
This is a basic mounting bracket for different occasions with a tight fit. Feel free to add this piece to other projects you want to mount to your headphones. The headphones don't touch/scratch the bracket while moving or stretching them.…
This mount fits perfect for the frame of the headset, so the soft foam is not squashed. Microphone is detatchable and can be stored seThis mount fits perfect for the frame, so the soft foam is not squashed. Microphone is detatchable and…
Use the Beyerdynamic DT1xx Ear Pad with this adapter for your STAX SR-Lxxx Earspeaker.
When connecting my Beyerdynamic DT 900 Pro X headphones to the laptop, they stick out quite some distance because of the thread to screw on the 6.3 mm adapter. This spacer fills the gap which looks nicer and hopefully protects the plug…
A replacement slider assembly for Beyerdynamic T90 and T70 headphones. Looks like it will probably fit T1/T5 and others.
You can use the screws and the joint, that came with the microphone, just like I did in the included picture. I have included a STEP file for your convenience. Please leave a well deserved like at the original maker's model.
Proven working: PLA 0,15 structural Snug supports everywhere (organics do work but are a pain to clean up) Remember to remove supports on the inside
Printing Just print them outside-down. The screw counterbores shouldn't need supports, most modern slicers can automatically bridge the inside. This image is looking up from below the build plate to show the bridges in the counterbore. I…
Wanted a hard case to stop my Beyerdynamic DT-770's from getting dinged up in my backpack. The commercially available cases were either too large, or required you to bend the strain relief grommet, which seems to invite problems, so I…
If you know what this part's actually called please tell me, also tell me if this fits any other headphones than the DT 990 PRO, a lot of their parts are compatible with multiple headphones. Beyerdynamic doesn't sell it so I couldn't…
Microphone Holder for a Beyerdynamic Space. Can be installed pretty much everywhere by pulling a velcro strip through the two slits at the back.
Update 11/19/2025 - Recent request for the outside slider cover, so I decided to go ahead and add it in. I also did a mild update to the inside slider cover. I think I can do a better job but if this means someone's headphones work vs…
Plastic cap (decorative) for Beyerdynamic DT 150 - i can add versions with some decors if you ask :)
Note that replacing the original earpads will significantly alter the sound of the headphones. Aftermarket bass heavy (Beyerdynamic) earpads would be preferred, but even with them the sound would be much different. I created this adapter…
Beyerdynamic DT 990 Premium — Cable Strain Relief Replacement A drop-in replacement strain relief for the Beyerdynamic DT 990 Premium , fixing the most common failure point: the cable breaking where it enters the left earcup. The Problem…
Replacement/adapter part for Beyerdynamic DT770 PRO headphones, designed to allow installation of custom or replacement drivers in place of the original broken units. The goal of this model is to make the DT770 more repairable and…
Rozlišovací kroužek na spodní část mikrofonů Beyerdynamic TG 550
Spare part for: Beyerdynamic DT 860, DT 440, DT 660 maybe: DT 511s A weak point is that the bow likes to break at the ball. There is no official spare part to buy. If the small bridges above the cable Channel interfere, pleased remove…
This is a clip-on cable guide for the gaming headset Beyerdynamic MMX150. It removes scratching noises induced by the cable by guiding it away from the body. The clip is held in place by a snug fit on the metal piece (probably wont work…
Replacement sliders for Beyerdynamic DT 770/880/990 headphones. Yes, you can buy original replacement parts – for an insane price! Also they will break after a short time again because they are just too fragile. This is a remix of…
I bought these puffy sheep-leather earpads to upcycle my old custom street headphones, but when i went to change the earpads i noticed that the stock ones were glued to the interface rings, and ontop of that the rings had been shattered…
Beyerdynamic MM1 measurement microphone cover. PET-G nozzle: 245deg bed: 70deg
Slider repair kit Fits: DT 790 / DT 797 DT 770 / DT 770 PRO / DT 770 PRO HT DT 880 / DT 880 PRO / DT 880 PRO HT DT 990 / DT 990 PRO HS 200 Dyn / HS 200 Rotor / HS 200 Trend HS 400 MMX 300 UPDATE - 30.10.2022: Some slight fine-tuning.…
One year ago my Lagoon headset broke at the frame. Thus i looked on the Beyerdynamic website for spares but they had no new frame for these headpones. So i repaired them with a 3d printed bracket wich worked just fine until the other side…
The original broke so I printed a pair of those brackets. The cable (connecting left to right speaker) constantly moved between bracket and my head, resulting in uncomfortable pressure points above my ears. Therefore, I remodeled the…
The cable is included with the J33 BT adapter (https://amzn.eu/d/bvBbztL). The adapter snaps right into the model, the buttons and ports are still usable and even the mic works great as a headset.
I love my headsets from beyerdynamic but sometimes I am really fed up with the prices of spare parts and how flimsy they are, I regularly change ear pads, cables, headbands and sliders. So I designed those from scratch to be tightened…
Spare part for beyerdynamic headphones dt 990 / 770 / 880 pro. This beyerdynamic headphones are my absolute favorites, but after some time the plastic parts one the site tent to break. I made some spare parts for that, it should be pretty…
Jack holder for beyerdynamic headphones 2 versions provided: thinner has more flex but also higher risk of snapping
Desktop stand for headphones including (but not limited to) the Beyerdynamic 770/990/1770 Pro/1990 Pro line. I'm sure it fits plenty of other headsets but I haven't specifically tested them. Requires support enforcement for Component 3!
Beyerdynamic Hinge Slider Replacement/Upgrade for DT770 Pro, DT770 M, DT990 Pro, DT990, DT880, Custom One Pro Plus, TYGR 300 R and MMX300 MK2
I can't remember, but I think you need to mirror it to get the left and right sides. And needs support because it is a quite complex part. But I know it has been working great in my grandpa's set.
The Hole is optional for a M3 Insert like from Ruthex. The Idea was to get more preasure at the Deskplate. The old one i had before got loose after some time. So I hope this one does not. If you might need another Measure for your…
Print it x2 Its a adaptor for DT 900 PRO X, make it more comfortable and you wont losing detail of sound :)
Add some 3M VHB double sided adhesive or other similar product to the back and stick it onto your DT880s
On photo, plate holder wrapped with leather textured vinyl wrap.
I had the problem that the popfilter of my DT297 is easily falling off. A zip tie was my first fix for that issue but was not optimal. The attached files are: OpenSCAD rendering script to adjust the size Rendered STL file for a working…
The model allows the installation of a Bluetooth adapter on the side panel of the Beyerdynamic Custom One Pro headphones. The Bluetooth adapter used can be found here: https://www.amazon.de/ https://de.aliexpress.com/ For installation,…
Do this at your own risk!! Did your DT770s break after the warranty expired, and you don't want to pay for the OEM speaker assembly? That happened to me… I thus came up with the idea to use a pair of mini speakers I had lying around to…
A quick project which is a replacement for Beyer's shitty plastic side brackets that attaches the speakers to the aluminum forks. I've had two sets of these break over the years, on two headphones. The plastic crumbles over time and snaps…
Used set of DT770s came with one of these rings missing, so I whipped up a replacement. Yes you can get replacements cheaply because Beyerdynamic is cool, but I wanted one now )) If I remember it snapped right in nicely, but thought I…
This is a holder for the "Y-Extension-Cable" of a beyerdynamic custom game headset ( https://north-america.beyerdynamic.com/custom-game.html ) to mount under the tabletop. Print Settings Printer Brand: Anycubic Printer: All-metal Mega…
Make your beyerdynamic headphones wireless with a FiiO BTR5. This should work on most beyerdynamic headphones, tested by me on the DT770 and DT990, but would most likely work on other beyerdynamic headphones with aluminum yokes. By…
In order to calibrate the SPL readings of your Beyerdynamic MM 1 measurement microphone, you need an acoustical calibrator, like the iSEMcon SC-1. However, the MM-1 is an odd duck: It has neither the common ¼" or ½" microphone head…
Beyerdynamic Fox pop Filter holder Printer: Creality k1 Filament: PETG
I made this extender to increase the depth of the ear cup so my ears wouldn't touch the driver foam. This was made on a Prusa Mini+ using PLA at .15mm structural with 100% infill. I have tested the fit on my DT 900 Pro X with Dekoni…
I made these headphones for fun. They are based off of the Beyerdynamic DT 770 Pros.
A friend of mine needed a mount for this microphone (BeyerDynamic TG D71), so he can fixate it in place inside the drum. He places some foam beneath it and screws it in place. The mount has 4 screw holes on the bottom, then it holds the…
Use typical M3 threaded inserts along with M3x8 bolts.
I liked the original design and it worked okay. But it was only a friction fit. So I did a slight change of the model and now when the part is in place, you can rotate is 90 degrees and it locks into place and can't be pulled out, unless…
resize to 10% i dont know why so big print fit test first if cant fit = try to incresss hole horizontal expansion (mysetting 0.5) my thrid party logitech ear pad size is 105x85 but i have 3 size for download 110x90 105x85 100x80
