Liczymy pasujące modele…
This handguard for the BK1S/2S replicates the look of the LVOA AR handguard in a 9.5" length. It is compatible with the handguard nut that comes with the blaster, as well as the original screw and nut. All MLOK slots are functional. The…
Got my hands on a BK1s but felt it looked too realistic so made this mod kit shroud has a thumbscrew knob that allows for tool-less removal; also has cross compatibility with the provided M-lok rails in the BK1S package body cover and…
Its a standard size buffer tube as the original one with the blaster is a little smaller then i'd like. Print with attachment point on the plate and print upwards. Good for getting some brighter colours on the blaster and its free. Use an…
For this conversion you will need either a dremel, hacksaw or flush cutters to make the cuts. You will also need 2x 4mm M3 heat sets and 2x 8mm M3 screws. Keep in mind if you are using talons you will still need to trim/file down the back…
The BK1s is a great AEB and great blaster overall, with one extremely annoying flaw: the extremely fragile stock lugs. The thin plastic of the BK shell and the high stresses at the small stock attachment lugs usually cause them to shear…
This is a barrel collet for the zius bk1s/2s that uses the sillybutts collet design.
Had this file with me for a while now but have not released it. This design is a remix of a Salient Arms GRY handguard commissioned by someone, which itself was a remix of the BK1S valiant shroud. I have realised SAI does not refer to the…
Tired of the stock barrel on your Zius BK1S/BK2S? don't have a 13.4mm chambered barrel? Well, this may help. If you do need this, the tolerances are pretty tight, i've shared 2 unthreaded variants below depending what tolerances you get…
A squared-off remix of KingDeeddee's Bk1s/2s talon magwell sleeve . Instructions to assemble are identical to the original. Print magwell base facing down, with supports.
Printed upright in Creality Print using a Creality K1C - CF PLA with a support threshold angle of 10 should generate supports just on the bottom section which will comes out easily. I didn't require brims or anything, your mileage may…
I Made a more comfortable charging handle, its shorter than the original one on the BK1s or BK2s. To install it remove the original charging handle and use the screw to fit this new one
Goes inside shroud to make the barrel and shroud more solid. V4 is looser on the barrel iirc
Speedseal plunger head I scrapped together while waiting for a better replacement and haven't worked out a secure mounting method for. Speedseals allow the plunger to move without a seal during priming (which is important for allowing the…
The Zius BK1s / BK2s High-Capacity Battery Stock is a replacement stock option kit for Zius’ AEBs. This upgraded stock can be installed toollessly and fits higher capacity 3S batteries to allow for extended gameplay sessions. This was my…
This is a remixed of Jian He Zhuang mag sleeve for the Zius BK1s. His version can't be used with a flared magwell and also was a little too tight printed with my Ender 3 v3 SE. I made the top tapered so that it can be used with a flared…
This part strengthens the thin plastic barrel position lips on the BK1s / Bk2s shell or if the these lips have broken then the part with the raised section can replace these lips.
This is an improved version of my original bk mag https://www.printables.com/model/1219069-bk1s-bk2s-magazine-short-10-dart-12-dart-max I have multiple lengths for different print bed sizes 180mm, 220mm 250mm. Only 180 has been tested due…
Adds pre extension to the return spring to improve cycling reliability. Won't seat the end cleanly for stronger settings. Backing off the screw a little can make it a little cleaner.
Mounts for allowing the attachment of the Rev 2 EX BCAR on to the barrel shroud of the Zius BK1S AEB blaster. V1 model is stand alone V2 model uses the Silly SCAR Collet system
Brooklyn Tony's stock lug but with a larger od section added to the stock interface to retain the stock more firmly and eliminate wiggle.
A simple build from the 3d print perspective BUT! you will need to solder an extender for your battery cable. Ive used an XT60 connector with around 100 to 140 mm of wire to reach the battery pack, (any junctions you add can be hidden…
its a extended charging handle for the bk1s/bk2s
I wasn't sure about cutting up my BK shell for a talon mod, so designed a magazine. I have an Bambu a1 mini so this mag is the limit of print bed size, it uses a talon spring so easy to get hold of. I've made multiple revisions and tweaks…
One of my favourite blaster is the BK1s. When I made the super drum, I was thinking what if there is a version I can use on it. So here is my attempt. DO NOT use more than 3 drum springs as I found that it can stop the piston from…
Print in TPU, PLA or PETG I printed mine in TPU with: 5 Walls 75% Infill
The Zius BK1s Decorative Barrel Shroud is a stylized replacement to the black barrel shroud included with the Zius BK1s AEB. Featuring top and Bottom Picatinny Rail and M-Lok side holes, this 3D part replicates the function of the…
