Liczymy pasujące modele…
UPDATE!!! 2-10-2026 I have been notified that the rear rail was undersized, sorry to anyone that had issues please re download the new rear rail and see if that works! Thank you for printing my designs even though I suck at designing lol…
Blockoff plates to keep FOD out of coolant passages during storage of LS engines.
link to BLOCKOGRIP link to BLOCKOBRACE UPDATE: Added New Charging Handle V3, haven't tested yet but I think it will be better. This design cradles the back of the frame and the front of the trigger guard, so it should fit most other…
Needed some covers for my type 1 engine before putting it aside in the garage, and could not find any online for free.
Storage blockoff cover for the steam ports on LS heads.
Blockosaurs make great pets, they love children and just want to play all day. Despite the Croc connotations the Crocoblockosaurus is a herbivore, check out the lack of gnashers! Requires 4 x 608 bearings
Cover the area where the distributor used to go, using this part. There are 2 version uploaded: One is designed for using thread inserts with. One is designed for using M6 heat-sert / knurled nut inserts (as seen in pictures). The OD of…
Don't take your car so seriously. We all would rather be driving a giant Blocko car, right? This model was designed for a Tesla Model 3 Aero Wheel, but might work for others. UPDATE: Added another cap cover with Blocko-sized studs so that…
This is a pair of EGR Blockoff Plates that I made for the 50CC engine in my 2018 TaoTao Pony Moped. These reuse the stock hardware. Mine were printed in ABS with 40% infill and five walls, top layers, and bottom layers. STEP files…
My friend went from cable throttle to DBW and forgot to get a block off plate for where the cable came through the firewall, so a few measurements later I made this! Confirmed fitment on R34, but should fit R32 and 33, as well as S13, 14,…
These are EGR blockoff plate design files for a 3000GT VR4 with OEM plenum and exhaust manifolds. They are verified to work with a 1st gen Federal spec car, but unknown for a California spec (with EGR temp sensor) and later gen cars. 3d…
All of my intakes are free-flowing, and when put on a port that was originally blocked, it's not the same. So these are some basic parts to compensate for that. The blockoff disc has a slight raised portion for centering, and the washer…
Greenwald Coin Slide Blockout/Blank 20-5002 Updated washer and dryer to free but didnt have enough blockout/blanks. I modeled it off the molded ones and printed on its side in PETG-GF at 0.12mm layer height but definitely not needed.
Designed to work with 3mm foam and ~3mm ABS rear panel and removed cable outlet. Add 1mm foam around the edge as shown in pictures and you should get a solid seal.
1" blockoff for pipes with BSP thread. Works great with my other pipemodels.
This is a PAIR valve blockoff cap for the Honda Ruckus. The PAIR valve normally takes atmospheric air in once the exhaust valve closes to mix into the exhaust gasses that then pass through the muffler, etc. It's normally blocked off once…
After removing the oil pump from a Yamaha TY175 or TY250 the grommet in the clutch cover and that the oil supply line and control cable passed through can be replace with this block off plug. I used NinjaTek's NinjaFlex 85A filament.
Plugs for the pk6 6 speed trans paired with the 1.9dci engine. Perfect for insuring that oil and dust don't exchange places during servicing or storage. The Passenger side plug is undersized to accept a few layers of electrical tape for…
A Small blockoff plate for the Remix - https://www.printables.com/model/1262750-neutrik-connectors-d-type-10-inch-patch-panel - for if you do not need all holes filled you can block it off with this part. Material PLA+ Black Layer Height…
A block off plate to close the lower rear vent holes in order to force fresh air to enter the side vents with fine mesh. The side vent openings should be sufficient. I printed it out of ABS and it is secured with 4 typical Fan self…
To print Blockos, place them upright in the slicer. It won't require support material as your 3D printer should be able to bridge across the hole at the base of the block. Do this for all the blocks except for the two wide block. Print…
link to BLOCKORONI link to BLOCKOBRACE This is not a grip, it doesn't use: 2 M4x30MM screws 2 M4 hex nuts. STEP FILES INCLUDED PUBLIC DOMAIN
link to Hex Version link to Folding hinge add on link to Hinge V2 link to BLOCKORONI link to BLOCKOGRIP Pistol brace ASSEMBLY BOM: 2 M3 Brass Heat Stake Inserts 2 M3x8 SHCS MOUNTING BOM: 2 M4x30MM SCHS 2 M4 HEX NUTS OPTIONAL DROP PROOF…
Changed Double DIN radio to single DIN then here is the cover to fill that empty space. Print on textured plate for pebble grain face. use ABS or PETG Fusion 360 file for customization
Description: These blockoff plates protect sealing surfaces from paint instead of having to use masking tape. They allow easy hanging in a paint booth (either professional or cardboard at your house), reduce waste, and enhance efficiency.…
The current rear rail is too narrow to fit the brace, so I made a wider one. Original files
G44 Charging Handle for BlockORoni 06/01/26 - Revised rear panel thickness to avoid breakage
Another part inspired by mnnthbx's Honda Ruckus hard parts, this time a light-less lazy eye, keeping it Swayze. Less post processing is required to get a nice looking part, and you can use the STL as a starting point for a customized…
