Liczymy pasujące modele…
Discord: https://discord.gg/kHFhCXZnxb GitHub: https://github.com/Rolls17/BugBu Print parts as oriented. Part description will tell you quantity and if supports are needed. All parts designed for 0.2mm layer height, 6 walls minimum, and…
Drop in and Adjustable only change I had to make was my X had to be Changed to -35 from the default -28. Just be sure to double check! Will need 2 x M2.5 x 10 and 2 M2.5 nuts for mounting.
The BugBu 260 has a printable area of 235x235x300 unless you slap on a Bambu build plate, then you get 260x250x300 build volume. This uses a cantilever bed to eliminate the closed loop belt system. All part are printed at 6 walls and 20%…
This is an upsized version of the BugBu 210 that uses an ender CR-10 24v heated bed, and gives a printable area of approximately 310x300x310. Just like the smaller version, this is a work in progress. This larger printer does require…
Based on the great work by mvasilakis (https://www.printables.com/de/@MVasilakis_835 and https://www.thingiverse.com/thing:3550867 ) I remixed the scope lever to fit on my utg bugbuster 3-9x32. It's thinner, the opening is different and I…
Big thanks to https://github.com/Rolls17 for the Design, Development of the Printer and the support for this conversion. Edited from the Voron Legacy Afterburner Carriage. Credits to: https://github.com/VoronDesign/Voron-Legacy
NOTE: Z Rotation Distance Will Need Changed From 8 to 13.1 For This Mod In The Config This mod will convert your BugBu 210 or 260 to a belt driven bed instead of triple lead screw driven. This mod will use all of the existing non printed…
This is a remixed mount for the CR Touch in a BugBu 3D printer.
Printed at 0.2 layers with 10% infill, no supports. While intended as a test print for the BugBu printer, feel free to try it on anything.
Remixed the Mantis XOL Toolhead to fit a dragon hot end and mount to the bugbu. Follow the instructions here: https://github.com/Armchair-Engineering/Mantis-Xol/blob/main/Assembly.md None of these parts should require supports.
If you don't want the loose power switch box in the files, you can use the foot. It will replace one back foot, and you can install your switch in the foot. There is a cover as well so electrical connections are not exposed.
This mod is ONLY for the 310 version of the BugBu. Just replace the same name parts from the BugBu 310 list with these parts to go tall. You will also need 2 - MGN12 linear rails for this mod. The linear rails will need to be 50mm shorter…
Was Inspired by LilMikey's work on the Tronxy to create a bed system leveled independently using Magnets and M4 balls. Eventually ended up mixing bits of Simplecore, the Voron Trident, and the original rail mounting method for the 260's…
Wir haben uns ein UTG Bugbuster (3-9x32 AO) zu gelegt für eine kleine Luftpistole. Leider fanden wir im Internet keine schönen Abdeckungen, die uns gefallen haben, oder die gut gepasst haben. Also habe ich ausgemessen und es in Fusion 360…
Adapter to fit Accushot sidewheel on the Bugbuster 3-12x32. Remove center rubber piece and replace with this.
Modded stepper mounts to fit W-Jack between the motor and the frame so you can tension the belts a little. You unscrew the motor a little and then use the screw on the side of the motor mount to tighten the W-Jack which moves the motor…
BugBu project I like the original design but I wanted to use this toolhead on my BugBu-ed Flyingbear P902. Added long holes for Bu's X carriage. This toolhead looks chunky but with P902 frame and BugBu hardware the 235x235 bed fully used.
Replaces the X carriage. Carriage bolts together with M3x25 from the rear. Dragon Burner mounts to the front. Sherpa mini mounting. to mount stepper to the rear, use sherpa spacer., otherwise motor will face front. need: 8 m3x4x4 heatsets…
I do not have a RPi 4 to use with the original backpack, so I split it in half and kept the motherboard portion. Same port position and holes out the top. Done with permission from the creator of the BugBu series. Rolls17. Go check his…
Prints fine on a BugBu 210 printer. Designed to hold a Meanwell 5v 5 amp PSU to power the Raspberry Pi on the BugBu printer. I was constantly getting “Undervoltage Detected” errors on my Pi when connected with a buck converter through the…
With the extruder I chose to use on my bugbu260 build the original bltouch mount left my crtouch sitting to low, so the simple solution to a simple problem, make the mount shorter. I have made 2 versions of the original design: V1-…
This is a Z-Axis Assembly to hold the Anet A8 bed in the Bugbu Core XY printer. For this to work you need to use 300mm lead screws and linear rods or you cut the Anet A8 ones to size :) you need to print every part twice. Some tolerances…
Built in the true RepRap spirit of continuous development, this custom toolhead for the Bugbu printer ecosystem is engineered for absolute reliability, precision, and high-speed performance. This design completely replaces the traditional…
Replaces the X carriage. Carriage bolts together with M3x25 from the rear. Dragon Burner mounts to the front. Sherpa mini mounting. to mount stepper to the rear, use sherpa spacer., otherwise motor will face front. need: 8 m3x4x4 heatsets…
This is a Bowden Toolhead for the Bugbu Core XY printer. It uses the “standard” V6 cooling fan and mount (that blue thingy). The fan shroud attached to the repo is a bad CAD reconstruction of the BiQu Hurakan fan shroud I had laying…
Split of the Cant Bed Mount to fit on a smaller build plate. print in loaded orientation with regular supports touching buildplate. Glue with ca Glue and use screws to locate and clamp. do not remove screws. 1.0 - added through hole and…
4 walls 20% infill attach the mount to the toolhead before the orbiter
This mod uses a 60mm bolt instead of 25mm. allows pulleys to be serviced without removing part from printer.
