Liczymy pasujące modele…
Its a tool to lock your camshaft at an timingbelt change on your VW 1.4 / 1.6 16V Engine. ➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖ YOU NEED: M6 Thread Drill Two DIN933 M6 Screws with a length of 20mm. Glue (If you want) ➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖ HOW TO: At the end of…
A simple multicolor box to keep BMW tool 83 30 0 494 606 safe from getting knocked around a garage or shop.
Model of the factory cam alignment block for the BMW M70, M73, or M43 engine. Print two for the V12s. Make sure to dial in your printer/filament so that the holder fits snugly on the cam. Faces chamfered to reduce elephant foot, corners…
Applications: Bronco 2.7L EcoBoost: 2021, 2022, 2023 Bronco 3.0L EcoBoost: 2022, 2023 Edge 2.7L EcoBoost: 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024 Edge 3.5L Duratec: 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016,…
Camshaft Holding Tool Kit for Ford 3.5L Ford 303-1655 F150, Expedition, Navigator, GT, etc
Its a tool to lock your camshaft at an timingbelt change on your VW 1.4 / 1.6 16V Engine. ➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖ YOU NEED: M6 Thread Drill Two DIN933 M6 Screws with a length of 20mm. Glue (If you want) ➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖ HOW TO: At the end of…
I have created a Camshaft Retainer Tool for BMW M50 and M52 engines. Designed for precise camshaft alignment during maintenance and repairs, this high-quality tool ensures secure handling and optimal performance. Perfect for any mechanic…
I needed a slightly modified version of the camshaft since i had only smaller bearings at hand. The bearings are for the selector arm (opposite of the drive wheel) and are 7mm instead of the 8mm of the original design. With those smaller…
These are designed to replace the unobtainable MD998761 special service tools to install the camshaft oil seals for a 6G72 (Mitsubishi 3000GT, Dodge Stealth, etc…) Specifically designed from measurements taken off of original,…
Replica of the original camshaft timing tool for a Ford Racing Puma 1.7. This advances the exhaust cam the required amount for the camshafts fitted to this engine. Please follow the workshop manual when using, this is a timing tool NOT a…
KM-6340 Camshaft Locking Tool for Opel / Vauxhall / Chevrolet (Z16XER, Z18XER) Camshaft locking tool for Opel/Vauxhall Astra H 1.6 - 1.8 . This tool is also compatible with some other Opel/Vauxhall models and brands (Chevrolet, Fiat…
A simple multicolor box to keep BMW tool 83 30 0 494 606 safe from getting knocked around a garage or shop.
example HappyHare Servo Config selector_gate_angles: 172, 149, 122, 65, 39, 15 # Optionally set default list of gate angles (overriden by calibration) selector_bypass_angle: 95 # Optionally set default servo angle when bypass is selected,…
I got a vintage Fisher Price Little People Merry-Go-Round for my niece, but it was missing a part. There's a little cam shaft and gear that are supposed to make it look like the carny is turning a crank to make the ride spin, and those…
General A Overhead Camshaft engine is an internal combustion engine with the camshaft placed in the cylinder head. This single cylinder model has four valves, with an engine capacity of 30 cc. This model was designed in Tinkercad.…
General This Ultramax camshaft drive system was uniquely applied to NSU vehicles, mainly the NSU Max motorcycle. From 1952 to 1963, approximately 160,000 motorcycles were made with this system. Two rods rotate on eccentric disks. All…
The file is of the teeth or claws that are part of the base mold for the gearshift hood frame of some models of Fiat Palio cars. As these are older models, this part is difficult to find or too expensive for my liking. And this part is…
You need to print two as they fit back to back, to make it easier to install and remove I wet sanded the back half to remove any layer lines which could cause them to lock up. Lock the camshaft drive belt pulleys together when removing…
Camshaft ring seal gasket installation tool 1.6 HDI , DV6 , DV6TED4. The tool helps to insert the ring seal gasket evenly without danger of displacement during installation
Designed for a 2009 Audi A4 with CAEB engine, but may fit other years/variants as well. The height of the boss may need to be adjusted based on the specific tool you're using. I used tool T10352/1A from the CTA Tools #1032 kit. I printed…
