Liczymy pasujące modele…
Hi! This is a 38mm NATO accessory rail I created with the new ARRI CCM-1 monitor in mind. There are currently (Nov 2023) no accessories for the new ¼-20 Pin-Lock standard so I decided to model one. Features: 38mm NATO Rail ARRI ¼-20…
I designed and produced as a spare part the plastic slider clip for the CCM Goalie Mask. The printing material is ABS and it is slightly reinforced to be stronger of the original. Category: Other
Created this model after needing a better way to install the Porsche PCCM Plus radio. The kit provides a square box that they recommend putting in the glove box. This does not allow easy access to the phone since the connection is hidden.…
Numbers plateholder(italy) for a 50ccm bike
I purchased two Hockey CCM Helmets in a end-off-life offer, but actually, the Full Face Visors I have are from Bauer. The holes for the clips in the CCM helmet are 11mm wider than in Bauer helmet and I designed this clip variant to avoid…
After removing the original venturi tube out of the airbox, i designed a grill to cover up the hole and to protect the air filter. It has the same contour as the original tube and can be attached with the original screws. It should fit to…
Model má trochu jiné rozměry oproti původnímu, kvůli dodržení stejných vlastností jako původní ze střikolisu, ale pasuje bez problémů s použitím původních štoubů. Materiál: Lipstick Red Prusament PETG Výška vrstvy 0,15 mm Tryska: 0,4 mm…
This mount is designed to add the front radar sensor (CCM) to a Ford Maverick 2024 and older without the need to cut your grill or remove the front bumper (Running wiring may be easier with the bumper off, but it is possible with the…
This is a small box with a press fit lid to cover the CCM2 DC speed controllers usually used for fans. I use them to control power wheel motors. I switch out the POT for a pot "gas" pedal. Link:…
Barton Classic 125 ccm Lamp Holder
“Oil is cheap, engines are expensive” This is why you want to change your engine oil regularly- not only on your car, but also on your little 50ccm scooter. This is what I wanted to do as well, and because I didn't want to use a regular…
This is a simple and strong 3D printed wall mount holder for hockey sticks. It is designed to hold Bauer and CCM sticks securely by the shaft and is perfect for storing or displaying your stick on the wall. Great for bedrooms, locker…
Tento model byl navržen jako náhrada původního dílu ze vstřikolisu. Pro zachování mechanických vlastností a tuhosti byly mírně upraveny rozměry, ale díl bez problémů pasuje za použití původních šroubů. Hlavní vylepšení (oproti předchozí…
You need: 4 x screw or velcro tape. Good luck ;-)
Ersatzabdeckung für den Öltank einer Motorhispania 50ccm.
The 2025+ compatible CCM does not have the same tabs with bolt holes as the prior years. So I designed this cradle to hold it in the proper orientation on the pre-existing printable mount. This means the mount should be oriented with the…
https://www.printables.com/model/1263277-2024-ford-maverick-adaptive-cruise-control-ccm-gri/files This is a TPU block to allow this CCM holder to mount to the lower grill of the 2025+ Maverick XLT. It is 39x40x75mm with beveled edges and…
You need: 4 x screw or velcro tape. Good luck ;-)
Printed on ender 3 pro with sprite pro direct drive extruder using tpu with shore hardness of 95. Using vase mode. https://business-lounge.heidelbergengineering.com/ch/de/products/hrt3-rcm/hrt3-rcm/gallery/
Model má trochu jiné rozměry oproti původnímu, kvůli dodržení stejných vlastností jako původní ze střikolisu, ale pasuje bez problémů s použitím původních štoubů. Materiál: Lipstick Red Prusament PETG Výška vrstvy 0,15 mm Tryska: 0,4 mm…
This is a simple and strong 3D printed wall mount holder for hockey sticks. It is designed to hold Bauer and CCM sticks securely by the shaft and is perfect for storing or displaying your stick on the wall. Great for bedrooms, locker…
https://www.printables.com/model/1263277-2024-ford-maverick-adaptive-cruise-control-ccm-gri/files This is a TPU block to allow this CCM holder to mount to the lower grill of the 2025+ Maverick XLT. It is 39x40x75mm with beveled edges and…
The 2025+ compatible CCM does not have the same tabs with bolt holes as the prior years. So I designed this cradle to hold it in the proper orientation on the pre-existing printable mount. This means the mount should be oriented with the…
Lost the clip that held the cage closed on one side of my nephews hockey helmet. Modelled a new one based on the side I still had. It doesn't include the small nub on the bottom that stops it from rotating but that isn't an issue when the…
Printed on ender 3 pro with sprite pro direct drive extruder using tpu with shore hardness of 95. Using vase mode. https://business-lounge.heidelbergengineering.com/ch/de/products/hrt3-rcm/hrt3-rcm/gallery/
CCM logo name tag (unofficial) Name tag for (ice hockey) skate bags with CCM logo to complete the look. Make sure to use a slicer which supports adding 3D text or use any of the free 3D tools (such as Blender, FreeCAD). When cutting your…
this is a 20ccm spoon/scoop you can easily print and don't have to use supports.
This is a replacement part that cannot always be purchased on all continents. I recommend printing this in PETG for durability and to withstand heat and direct sun exposure. I printed .08mm layers with a random seam position. The printed…
Ford Mustang Gen 6 (2015) Steering Column Control Module (SCCM) PCB housing Ford Mustang Gen 6 (2015) Steering Column Control Module (SCCM) PCB housing for projects using said car as a donor. You need the SCCM for hi-beams and turn…
Lost the clip that held the cage closed on one side of my nephews hockey helmet. Modelled a new one based on the side I still had. It doesn't include the small nub on the bottom that stops it from rotating but that isn't an issue when the…
Servo mount for fuselage, fuselage Connector-Clip, Connector-Adaptor for center wing
