Liczymy pasujące modele…
Size: 125mm x 90mm x 77mm WEAVED version: Filaments: PLA Vanila White (body), PLA Jet Black (eyes) and Filament PM PLA+ Pastel Bubblegum Pink (nose) CROCHET/KNITTED version: Filaments: Filament PM PLA+ Pastel Bubblegum Pink (body) and PLA…
Wydruk około 0,04 €–0,05 € nettoWstępna wycena jednego wariantu
This model is ideologically based on the line Crochet tension ring Crochet Ring Crochet Ring (parameterized) New ideas have been incorporated into the model and the result feels significantly different. Printing recommendations:…
Wydruk około 0,16 €–0,19 € nettoWstępna wycena jednego wariantu
Just a simple crochet hook, can increase size within slicer if needed, 20 minutes , less than a metre of filament. 0.2 res No adhesion No support. 20% or above infil.
Wydruk około 0,17 €–0,21 € nettoWstępna wycena jednego wariantu
This ring is a full remake of the Crochet Ring originally uploaded by @Milan . After using the original for a short while, my wife asked for a few changes. Specifically, she requested (1) a taller guide rail at the base of the ring and…
Wydruk około 0,59 €–0,72 € nettoWstępna wycena jednego wariantu
Crochet Block board with 4.10mm hole designed for 4mm wooden dowels
Wydruk około 21,54 €–26,32 € nettoWstępna wycena jednego wariantu
I designed this box to hold my wife's crochet hook set. It is meant to fit the Eleggant Hooks set. It holds the somewhat bulky egg shaped handle, the hooks, and the little box of O-rings. I also added a place to hold her notes. (My wife…
Wydruk około 9,37 €–11,45 € nettoWstępna wycena jednego wariantu
Un clip et deux versions de crochets pour suspendre des balais, des pelles, … bref du rangement / one clip and two versions of hooks for hanging brooms, shovels, ... more and more storage
Wydruk około 0,53 €–0,65 € nettoWstępna wycena jednego wariantu
My wife crochets and knits. She has a lot of needles and hooks. When I first started 3D printing, I wanted things to design and make. So, I designed this about 4 years ago as my first box project. It uses filament for a hinge - which has…
Wydruk około 0,18 €–0,22 € nettoWstępna wycena jednego wariantu
🇬🇧 : Just a double hook for coats, bags, etc … Printed directly on the side No raft needed No support needed 30% infill recommended PLA possible (PETG recommended for duration) 🇫🇷 : Juste un crochet double pour manteaux, sacoches, etc ……
Wydruk około 3,64 €–4,44 € nettoWstępna wycena jednego wariantu
36 holes, two or three colours
Wydruk około 2,22 €–2,71 € nettoWstępna wycena jednego wariantu
Towel hook for heater Advised material : PETG or polymer with higher glass transition / melting temperature. PLA will soften under heat. Should work in summer though. Originally designed parametrically with the following values: - tube…
Wydruk około 0,28 €–0,35 € nettoWstępna wycena jednego wariantu
36 holes, two or three colours
Wydruk około 2,32 €–2,83 € nettoWstępna wycena jednego wariantu
dragon bottom - first color is light, second printed color is dark (black) and third is that one you just need to use because there is too little of it for any project but it is waste to throw it into trash bin - oval bottom is for same…
Wydruk około 5,45 €–6,66 € nettoWstępna wycena jednego wariantu
Easy model. Print every size of hook from this set with different color of filament. This model is suited for print in place, no brim or supports. Print with PLA, smooth it with fine sandpaper. (Or you can print it with materials for…
Wydruk około 4,41 €–5,40 € nettoWstępna wycena jednego wariantu
crochet pour rideau de douche Le 1er fichier est le crochet simple et le 2em est fait pour en imprimer 12 ( pour les 12 œillet du rideau) 6,8cm de long 3,8 de large 0,5cm d'épaisseur
Wydruk około 0,20 €–0,24 € nettoWstępna wycena jednego wariantu
Crochets pour des rideaux de pergola Hooks for pergola curtains
Wydruk około 0,53 €–0,65 € nettoWstępna wycena jednego wariantu
Coat rack with two hooks to be screwed into the wall. Porte manteau avec 2 crochets à accrocher sur un mur.
Wydruk około 4,89 €–5,98 € nettoWstępna wycena jednego wariantu
Crochet pour accrocher un casque ou tout autre objet sur une paroi de séparation d'environ 6-8 mm d'épaisseur. La forme du crochet inclut une pince pour tolérer des variations d'épaisseur. Instruction d'impression A imprimer sur la…
Wydruk około 1,39 €–1,70 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Crochets De Rangement Suspendus
Wydruk około 0,70 €–0,86 € nettoWstępna wycena jednego wariantu
Bonjour, J'ai refait le crochet de la couchette, car je l'avais cassé. Je l'ai simplement fait en PLA (Prusament) et j'ai remarqué, après avoir fait quelque test de traction qu'il étais beaucoup plus solide que la pièce moulé d'origine.…
Wydruk około 3,42 €–4,18 € nettoWstępna wycena jednego wariantu
I'm fairly new to crochet after decades of knitting, and while keeping up with the counting still gets to me, I love the sheer possibilities with the medium. The randomness of freeform crochet piqued my curiosity early on, but the thought…
Wydruk około 1,51 €–1,84 € nettoWstępna wycena jednego wariantu
Ma femme m'a demandé un crochet pour accroché les gants de toilettes, voilà le résultat, la barre fait 10*350mm. C'est mon tout premier modèle.
Wydruk około 1,39 €–1,70 € nettoWstępna wycena jednego wariantu
permet de tenir le badge à votre poche
Wydruk około 0,17 €–0,20 € nettoWstępna wycena jednego wariantu
Crochets pour calendrier de l'avent - Wooden Advent Calendar Hooks
Wydruk około 0,19 €–0,24 € nettoWstępna wycena jednego wariantu
Een haak om mijn zware steekspade op te hangen. Een zelf gemaakte spade op smalle gleuven te graven, zoals voor aflopen aanvooren elektriciteits kabel enzo....in het gazon. A hook to hang my heavy spade. A homemade spade for digging…
Wydruk około 1,90 €–2,32 € nettoWstępna wycena jednego wariantu
The person I love has a crafty hobby: crocheting! So she told me about those crochet rings that help maintain the right amount of tension while preventing the yarn from causing to much friction on your finger. She found this ring by…
I designed a 3D-printed version of a spinning skein holder. The spindle is held captive by a small keyed shaft pressed into a 608 bearing. Print Settings: 0.4mm nozzle 0.2mm layer height Supports only on spindle and spindle peg 15-20%…
After the success of the Ghost Booh for Halloween 2022 https://www.printables.com/fr/model/291519-ghost-booh You will love The Ghosts Booh crocheted for this Halloween 2023 ! This time 2 different versions : With or without a smile And of…
Youn can create patterns up to 190x190mm. The space between holes is 10mm each. Print the first two/three layers at 5/10ms .28mm layer height No Supports needed. For the Poles Print at least 4 of them. For improved pole design You can use…
A kit for crochet lovers where you can organize your crochet tools and also help you by spinning the yarn without falling on the floor or tangle. The magnet used was obtained from an old speaker with a neodymium magnet like this Date:…
I made some simple thin crochet basket bottoms in openSCAD. The wood ones are nice to look at, but if something gets spilled or you want to make a basket for the bathroom, it is nice to have something water resistent. Let me know if you…
Customized version of https://www.thingiverse.com/thing:53854 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=53854 Instructions Using the following options: diameter = 5.5 length = 145 throat_angle = 10…
Print in place, just a simple stitch marker. Designed by me but originally posted on my Makerworld page . Print in a rigid material and multiply for however many you need.
A crochet block designed for my girlfriend. Used to help shape the squares so that the end product looks better. I used ½" diameter wholes, and was told the dowel rods were too big, so I also created the poles with 3/8" diameter. Also…
simple needle for crocheting, slightly rectangular profile. flash drive for size reference on the second photo. available in small, medium and large.
A knitting bowl to prevent yarn balls from running away is a thoughtful gift for your grandmother. :) Simple to print, just need to add several supports (example at photo) P.S. Added an updated design with extra holes.
Testing of it in practice is still in progress Requested by a friend and working with her on preferences and design. Included multiple ring and hole sizes (ring size is just inner diameter in mm, because I got confused with all different…
I made this needle really big(10 cm) so it's good for crocheted big toys. I use it a lot to sew parts of plush toys.
To help reduce the chances of yarn snagging on your hook, I recommend printing at the lowest layer height you can. Some sanding may be needed, but for me wasn't needed. Happy crocheting! Layer height 0.12 mm Infill 25% Wall shells 3 PLA…
🧶 Stitch Markers Description: Versatile stitch markers designed for knitting, crochet, sewing, and various crafts . Their smooth edges and rounded shape ensure that the stitches glide easily without snagging, unlike sharp metal safety…
This is a basic blocking tool for crocheting Granny Squares to keep them all the same size and with straight edges. I designed this tool in OpenSCAD so that anyone can download the program OpenSCAD and adjust the parameters in the file.…
Who doesnt love a cute DUCK in a Crochet Style ? If you have any issues with the File etc , do not heistate to message me here or on my Discord ! Files Included are : Body DONT KNOW HOW TO PAINT THE EYES ? I have a tutorial on my Discord…
Want to finish your crochet work? Print this needle and be done.
my wife was complaining about not having nice handles for her crochet hooks so i spent some time and made a nice whole set for her. best printed as is when loaded Will only work with TPU Update 1: had to make the 10mm hook handle a little…
A parametric crochet hook. Proportions copied from commercial stamped aluminium ones. It was a cool challenge to model in OpenSCAD, but the trial print in PET-G that is on the photo was not smooth enough to be comfortable to use. Perhaps…
This adorable Crochet Ghost will be loved by kids and adults. It looks awesome printed in a single color or it can be printed in colors too. You can get the factory files from Maker World. It has been designed with lots of details, but it…
This is the most common size crochet I use to teach people how to crochet. Size 5.5mm is equivalent to a US hook size I.
Printed with PLA, at 0.3mm, 15% infill. No support needed when printing top and bottom separately. I've glued the top and bottom parts.
Easy to print stitch marker How to print? 100% infill 0,2mm layer 60 markers print time is ~ 1,5h Enjoy and post realisation :>
Printing recommendations: Nothing special here but I recommend a concentric top and bottom fill pattern. Check the provided .3mf file. Parametrization I exported the basic size series as stl files. However, the strongest part of the…
Only needs support on the opening of the hole Use double-sided tape to hold it in place while using it
An updated version of my last knitting needle holder. I've adjusted the design so that it prints great without any supports. Make sure that the holes face down on the bed, for best results. I added a small angled pocket on one side to…
This hook was designed and refined via inputs from a lifelong crocheter. The tip of the crochet hook was elongated to enable the tool to easily pass through the yarn. The hook extends past the handle with a shallow angle to ensure a…
3mm and 5.5mm crochet hooks. These should be printed with 100% infill. Please tell me if you want any in a different size by commenting.
You are not allowed to take metal crochet hooks in the hand luggage of an airplane, but my wife likes to crochet during a long flight. Actually, a plastic crochet hook is also not allowed, but is allowed with a blind eye. Because a…
I wanted to try a marker that is easy to remove but will stay in place .
Remix of Marcus_GT500 crochet markers. Print with no support. Added numbers to count knitting rows. Slightly larger overhang Rounded corners. Print different colors for 10-19, 20-29 etc Category: Other
22 cm Crochet blocking board in 4 parts to print on the Prusa Mini+ including stabilization holders. Also known as Granny Square blocking board . Because the Prusa mini has a print bed of 18 cm * 18 cm, I have a blocking board of 11 cm…
This frame is used to wet block 3.75 inch crochet granny squares. It could probably be resized. I printed with PLA, 0.2 layer height, and 15% infill.
Easy model. Print every size of hook from this set with different color of filament. This model is suited for print in place, no brim or supports. Print with PLA, smooth it with fine sandpaper. (Or you can print it with materials for…
Hello, heres a collection of crochet bases for you to print. I have created a few to start and can create more variants if there are some you would like. The file names have the sizes as the names. So 200x180-9 is a base that is 200m by…
A simple Crochet hook rack for a set of 17 hooks. Hook Size Hole size in the rack 8,0mm 7,0mm 6,0mm 5,5mm 5,0mm 4,5mm 4,0mm 12mm 3,5mm 3,0mm 2,5mm 2,0mm 10mm 1,75mm 1,5mm 1,25mm 1,0mm 0,75mm 0,5mm 8mm
[Français en-dessous] [EN] [Update 03.02.2024] I noticed some mistakes in the files I uploaded. I will print more of them, I corrected it for you and add a new one… "Classic" Hook: small place for hanging; 15mm “Large” Hook: bigger place…
Use 7 pieces of filament about 6-8mm long to make location pins for gluing. Make sure the faces mate flush before gluing with CA. Sides need a bit of smoothing with sand wet sandpaper.
Meet Hedgehog's Cozy Autumn Haven , your charming companion for knitting and crochet! This adorable organizer holds your knitting needles and crochet hooks in its quills. It features a detachable yarn holder (spool) for smooth unwinding,…
A crank drive thread winder, for sewing, crochet, tricot etc. You may transfer thread from cones or hanks to balls. May be used with any kinds of threads, like sewing threads, tricot wool threads, strings etc. Printed with PLA, two layers…
Print with enough wall thickness so the hook end is solid. Orient the part so the main flat end is against the build plate. It should print fine without support using a 0.4mm nozzle and 0.15 layers. 1.2-1.6mm walls and 25% infill works…
Improved poles for Crochet Granny Block Better printability Tight fit
Have you ever lost a hook into the depths of the couch cushions? Or let your cousin borrow it and he lost it into the depths of HIS couch cushion? Well don't worry, because now you can print your own! Color Change: No (You can if you want…
Create sturdy, perfectly shaped crochet baskets with this printable basket base , available in six sizes: 100 mm, 120 mm, 130 mm, 150 mm, 160 mm, and 170 mm in diameter. Each template includes precisely spaced holes and a built-in legs ,…
Crochet porte serviette destiné aux radiateurs réalisés avec des tubes diamètre 24mm entre axe de 36mm 2 tailles épaisseur 11mm et 16mm Towel hook intended for radiators made with 24mm diameter tubes, whose center distance is 36mm 2 sizes…
Just in time for Halloween, a crochet bowl that doubles as a candy dish. The design includes organizers for hooks and a pocket for scissors, (small) TV remote controls, etc. This design prints without supports. I generally print it in PLA…
Suite à la discussion sur la butée anti-bascule , voici une pièce pour raccorder le guide parallèle et d'une scie circulaire Festool TS55 EBQ et le rail FS de la marque. Il est possible de n'utiliser qu'une seule pièce pour éviter la…
This is a safety pin to use in crocheting or knitting, when you put your work off and want to avoid damaging it. I made it for my wife. Works fine when printed with PETG, it is more elastic than PLA. Please better print it slowly to…
Push-in eyes for crocheting characters and toys Different models allow multiple combinations to display various emotions (see pictures) Eye diameter: 10mm Print notes No supports needed If there's not enough adhesion during printing it's…
Available as a an all-in-one print, or two parts that screw together. Printed in PLA with 15% infill.
This crochet needle with 3.5 mm diameter is fully 3D printed and might work good enough if a professional crochet needle is not at hand. Print without supports.
I created this base for my wife who like to crocheting. Its a 27 by 21 by 0.2 cm. Edit 06/06/2023 added another base, square, but with 4mm holes.
Salut, Voici une impression pour créer un crochet pour cadre photo avec un simple clou (20mm x 1,3mm environ). Parfait pour des cloison en plaque de platre Parfait pour des cadres de 10x15 à 20x30 Testé jusqu'a 4kg 0,35g de filament…
My wife really likes this model a lot but I noticed that I couldn't find it or something similar here on Printables so I wanted to reupload it. It uses a standard skateboard bearing to spin. From the original upload: Print both parts,…
Hey! So i made this model mainly to crochet a bag like this; CC: sarma_bags The bag bottom is 18 x 8 cm 🖤 So if u wanna make one like it, here is a video and what type of yarn i used!; - Hobbii Recycled Cotton Cord (4 mm) - Link to the…
Screw on handle for cheap Shein crochet hook set. The size numbers were added in prusa slicer.
Crochet blocking board for blocking out granny squares, Afghan squares and other small knits like hats, booties, etc. My wife requested a larger version of the original board so I expanded it to be 10 x 10. I also modified the pegs to be…
Remix of the original Crochet Hook Holder by Nadav Halwany - Added pegs to allow the top and bottom to snap together without glue. Tolerances vary per machine and settings, so the hole and or peg may need to be sanded to fit.
Easy model. Print every size of hook from this set with different color of filament. This model is suited for print in place, no brim or supports. Print with PLA, smooth it with fine sandpaper. (Or you can print it with materials for…
This 3D printable bear features a charming knit texture, giving it the appearance of a handmade toy. Height: approx. 96 mm Supports: recommended Perfect as a decorative piece, gift, or just a sweet little companion ❤
Customized version of https://www.thingiverse.com/thing:53854 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=53854 Instructions Using the following options: diameter = 10 length = 150 throat_angle = 10…
This is best printed in by splitting the top and bottom parts so that no supports will be needed. Some file work is needed to get the two parts ready to glue together.
This handy little tool is perfect for any knitter or crocheter. It features holes to measure the size of knitting needles in millimeters and US sizes, and crochet needles in millimeters and letter sizes. It also has a ruler on the other…
Grab your free adorable crochet dragon now on all platforms while you can. Super flexi, quick and simple to print, comers with multiple print profiles & 2 variants, with and without keychain. Comes with 2x STL files, 3 Bambu studio…
Easy model. Print every size of hook from this set with different color of filament. This model is suited for print in place, no brim or supports. Print with PLA, smooth it with fine sandpaper. (Or you can print it with materials for…
Simple remix od this model by mijo11 made by my girlfriends request. Just modified one end to make it really pointy so it can be easier applied. Print with high infill or many perimeters, just to fill it as much as possible to make it…
attention se si né pas fait pour l'escalade
Very large crochet hooks are often hard to find as well as expensive, so I created a US size S (19mm) hooks with the customizer below. I had to shorten it due to the limitations of my print bed, but it turned out very usable. At 0.2…
Simple crochet eye that prints without support structures.
This is an IKEA SKADIS crochet hook holder with Clover branded hooks and darning needle. Includes a space for the Clover Amour Crochet Hook Set, the Clover Darning Needle Set and an additional 7.0mm and 10.0mm hooks. STEP file is there…
Wall-mounted hook for a chainsaw Compatible with Stihl, Husqvarna, and Jonsered I decided to provide an unbranded version, as it is easier to print using larger nozzles—even though I’m aware that some people might resell it without giving…
Design Concept This modular blocking system includes a suite of geometric shapes—classic squares, high-density circles, and radial frames—specifically engineered for fiber arts. Each board features a precision-drilled grid compatible with…
Easy model. Print every size of hook from this set with different color of filament. This model is suited for print in place, no brim or supports. Print with PLA, smooth it with fine sandpaper. (Or you can print it with materials for…
