Liczymy pasujące modele…
EDIT 9/27/26: Added new, basic assembly instruction and updated (incomplete BoM) EDIT 3-7-26: Uploaded files for the new, Linear Bearing 3D Printed Focuser! The focuser drawtube runs on two LWL7B Linear Bearings with a T5 Lead Screw for…
EDIT - Read full description below as some parts have changed. Please join the discord if you have questions as I may not see them here in a timely manner! - https://discord.gg/QdPa9ed6Jq Building of the success of the DBS114 , I now…
I made a lid for the MTG card storage box created by @MakerDBS
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This is a set of mounting brackets so you can hangs the DBS-22 Drill Bit Sharpening jig from the wall There are 3 parts One for the base plate One for the drill holder One for the magnifier
Here is the PrusaSlicer version I used on my Prusa MK4 with MMU3. You can use the recommended 3MF or STL with the manual print instructions below. Manual print instructions Print at: 100% infill Layer height: 0.08mm First layer height:…
I will be making more and making a Rocket League soccer/heat seeker ball
Wall bracket for Parkside PDBS 2200 A2 pneumatic drill with four screw holes. If you like my designs give me like and share. If you like them a lot invite me to a coffee. https://www.buymeacoffee.com/kjbturok…
Aston Martin DBS Superleggera This design can be scaled to any size in your slicer. Print flat with ~5% infill to save material. Perfect as: wall decoration desk decoration gift for fans Category: Signs & Logos
Additional 150mm section for the DBS150 Astrograph by @DaveAldrich_1395060 for focusing the D150xF750 primary mirror.
Aston Martin DBS 770 Ultimate as a 3D Model. This design can be scaled to any size in your slicer. Print flat with ~5% infill to save material. Perfect as decoration. Category: Signs & Logos
If you want to get the focal plane of the telescope as close as possible to the secondary mirror, you can use this modified printed front piece together with the following extra short focuser:…
This is a mod to the DBS114 Astrograph . The new rear tube section has a threaded hole to which you can attach: a funnel with an 80mm fan; a cap to close the hole, if no fan is needed. The funnel supports an 80mm fan (e.g. a Noctua NF-A8)…
Aston Martin DBS Superleggera scale car model stl for 3d printing, a realistic civilian vehicle diorama piece based on the real grand tourer. Use it for car collection display, tabletop decor, garage themed layouts, and custom background…
**************** If you download 💾 or collect 🗄 please hit the LIKE 👍 button. 😀 If you print 🖨 it post a picture 📷 / MAKE ! 😄 Let me know how it works for you.❔ 🙂 Don't forget you earn Prusameters🧵 when you post a MAKE ! ****************…
Aston Martin DBS Superleggera Keychain This keychain is inspired by the stunning Aston Martin DBS Superleggera , a perfect accessory for fans of British luxury and performance! For the best results, print with a 0.2 mm nozzle for finer…
logo wo DBS drauf steht
This aperture mask is designed to fit onto the mirror cell of the DBS 114 by Dave Aldrich:…
This blast effect was made for the "S.H.Figuarts Dragon Ball Super: Broly - Super Saiyan Broly Full Power". This effect holder clips onto Broly's gauntlet. Then you can connect the holder to the blast effect as seen in the picture. You…
The dimensions of this bike and wire are: Bike frame diameter: 32mm Wire diameter: 5mm Bolt hole: 4,6mm The Fusion file has parameters that can be modified, but the clip will probably not fit any dimensions. Printing instructions ABS,…
Turns out that internals of the door latch differs based on the door bar style on the Aston Martin Vantage. So I had to make a bracket based roughly on the version Aston may or may not still sell. You need heat inserts, and your milage…
Hello all <3 Welcome to my first model! A simple idea, yet I have not found any online! Just fill up your deckbox with these so it doesn't lean over/tilt/bend. I made this the same 66x91cm dimensions as your typical TCG outer sleeve, for…
EDIT - Read full description below as some parts have changed. Please join the discord if you have questions as I may not see them here in a timely manner! - https://discord.gg/QdPa9ed6Jq Building of the success of the DBS114 , I now…
The dimensions of this bike and wire are: Bike frame diameter: 32mm Wire diameter: 5mm Bolt hole: 4,6mm The Fusion file has parameters that can be modified, but the clip will probably not fit any dimensions. Printing instructions ABS,…
The Persuaders-Lord Brett Sinclair-Roger Moore - 1971 3D printable model.
I made a lid for the MTG card storage box created by @MakerDBS
Here is the PrusaSlicer version I used on my Prusa MK4S with MMU3. You can use the recommended 3MF or STL with the manual print instructions below. Manual print instructions Print at: 100% infill Layer height: 0.08mm First layer height:…
These three stl models are designed to compliment the DBS-150 telescope. The larger stl sleeve model is designed to be printed in TPU and stretch slightly over the rear of the telescope. The TPU Bumpers are designed to firmly secure the…
I did not want to use glue for the carbon fiber tubes, in order to dismantled for maintenance (dusting) of the main mirror, I have added this rawl plug system to keep the tubes together tight. Also I incorporate feet so when you put the…
The Persuaders-Lord Brett Sinclair-Roger Moore - 1971 3D printable model.
MK2 Dbso coach model railway carriage model train
![The Deck Box Spacer aka TDBS! (TCG) [[multiple versions in Files]]](https://media.printables.com/media/prints/4ae680ed-2211-4fa2-b94b-ff4c2309381c/images/14087695_2259bed5-be93-4740-aabe-a3b689c018eb_d4abd3df-86ee-4e73-9e24-667b40849981/screenshot-2026-10-14-021036.png)
