Liczymy pasujące modele…
Also known as the "Deck d--k" on Reddit. This is a quick jig that makes putting deck boards on a deck go a lot quicker. It sets the proper gap between the deck boards, and it aligns with the joist beneath and acts as a screw guide so you…
Easy to use spacers for laying down your decking. Print as many as necessary. Easy to put in place and pull out afterwards Comes in 2,5, 3, 3,5 and 4mm variants Insert depth is 15mm
Spacers for decking 7mm for dry wood 4mm for wet wood
Alignment jig for decking screws. Made for 145mm planks or narrower. With 7mm spacer.
This is used to maintain a specific position for the screwing of a 90 mm merbau decking board. It will also consistently deliver a about a 4 mm gap between the boards which looks pretty good and allows for some movement. The smaller…
Are you building a new wooden deck and want a perfect result? The key to a professional look is absolutely consistent and even spacing between the boards. This smart T-shaped spacer is designed precisely for this purpose, saving you…
A spacer set to hold wooden boards at the correct location. Can be used for Decking, Woodworking or anything else. The spacer has shoulders to hold it in the woon and a handle for easy removal.
Trex decking spacers to assist in installation of Trex decking. The larger spacer is used during installation, while the smaller spacer can be permanently installed/placed (for issues such as warped boards). No supports needed, recommend…
Summary Tools are designed to be printed with the base of the tool on the printing plate with NO supports required This decking installation tool has been designed to fit onto the medium and heavy-duty clamps manufactured by Irwin and…
Much like my first iteration of this product, this tool allows you to have a perfect ½" overhang on your picture frame trex deck boards. This tool differs from the original in that you can lay your picture frame boards without first…
*Update 6-28-24 * - This tool is for use when you already have your facia board installed, or are not running a facia board at all. For proper spacing and install picture frame deck boards before adding facia, please see my other version…
Quick design decking spacer, 3,2mm /1/8" Category: Outdoor & Garden
Place over decking board where the beam passes underneath. Jig selv aligns over the beam. Best suited for 28 mm decking boards, over 48 mm beams.
5mm decking spacer with extended sides to ensure it stays in place. has a large handle so removing it is easy even with gloves on.
A customizable spacer for placing between planks on decking or shelving to provide a consistent gap for the project. Print two, three or more as required, depending on the length of plank and fixing points you are using. I've included…
The models were drawn in FreeCAD. Feel free to change the parts to suit your needs. I printed all parts in gray TPU from Amazon. As the names might suggest the simple version is easy to print and works great and the experimental version…
I always liked the idea of the melee mimic and dubbed my version "The Decking Mimic" Comes with the complete chest and mimicified version in two parts. Enjoy. UPDATE* I forgot to upload the detailed version of the chest. Fixed now. Might…
A 90mm merbau decking board screw guide to ensure you have evenly spaced decking screws for that professional look. Designed in Tinkercad because I am a simple man. Print in whatever material you want at whatever resolution you want. The…
The Silt Walks are the arteries of the district a chaotic mess of planks, rope, and sprocketed walkways held together by sheer stubbornness. They’re narrow, slippery, and usually suspended over a drop that’ll break your grit before you…
Here we have the second part to parts for the pottery buildings I am currently working on for my 00 train layout. Included in this we have a set of stair treads, the side frames which include the stringers, handrail and support structure.…
This easy to print model makes equal spacing of decking and screws a breeze. Use these and you'll look like a pro! Left and right stagger to suit any condition - use both to create perfectly spaced joints. A simple PLA print will last a…
This is a simple model when laying wooden deck. Gets you perfekt straight screw rows and the right distance. This tool is made for wood deck 120x28 mm and gives you 2 mm spacing between each board, which is a good distance when laying…
This model consists of cross-shaped and T-shaped spacers designed to maintain a uniform 5mm gap between wooden decking boards during installation. The geometry features vertical fins that fit between the planks to define the spacing and…
Clips for mounting elephant (and maybe other brands) decking boards. Dimensions (in mounting direction) Top: 22.5x51x6mm Bottom: 6x51x6mm Hole: 4mm Printing with at least 50% infill.
This is an adapter to use normal Wolfcraft Pro L one-hand clamps for laying wood or WPC decking. Dies ist ein Adapter für normale Wolfcraft "Pro L" Einhand-Spannzwingen, um diese bei der Verlegung von Holz- oder WPC Decks einzusetzen. Am…
I made a simple one fitting for 12cm broad decking boards. In addition I made small spacers for having the right margin to the wall or inbetween the decking boards.
Designed for Veranda 15/16 in. x 5-1/4 in. x 16 ft. Stone Gray Grooved Edge Capped Composite Decking Board (Homedepot)
For the new profile Trex boards (and possibly others) this template helps you mark for the correct screw or pre-drill location I used PETG since this is going to be left in the hot sun and I don't want it to warp Also included are some…
I designed this thing to facilitate installation of composite decking boards. Similar the tools you can buy from the manufacturer of your boards, this tool will helps ensure accurate board-board spacing and screw placement. I provided a…
This drilling template is designed to streamline the installation of wooden decking. The tool features a slotted, fork-like end that fits over a previously installed screw head within the gap between boards. This physical reference point…
This is a set of shims and drilling templates I designed as I was building stairs for my deck (2 steps). They also ensure a 5 mm spacing between boards for expansion. In France, the sections for standard boards are 145 mm x 27 mm or 120mm…
Print on edge. I did 7 walls and made it solid Meant to put 3mm gap between boards Also will sit up against a 4x6 stringer and place screws 1" from edge of decking. you could trim it if you are using a 2" x 4" or 6" as a stringer. Left…
You will need one short decking screw per decking board. Drilling the hole beforehand is strongly advised, because otherwise the screw when screwed in will veer into one of the existing holes on one either side of where you want it to go.…
Description: Lost or broken a wooden piece from your IKEA RUNNEN outdoor floor decking? No problem – this printable replacement slat is designed to perfectly fit the standard RUNNEN wooden tile system. Simply print, snap in place, and…
A funnel for the Wagner sprayer bottle to avoid spilling paint when pouring it in.
Simple deck\light shade Print inner in white or another color to let light through. Category: Outdoor & Garden
Quick printing, reusable deck board spacer. String on a piece of cord (paracord) to keep from dropping while in use. Tapered for easy removal. Print as many as you need. ¼ inch spacing. The ones shown are only about half height, My…
A hidden inner corner fastener/cleat for a picture frame deck corner that still allows for some wood movement in the lengthwise directions. The corner fastener should be mirrored for the other orientation. Also an angled edge fastener.…
This is intended to be used when building other designs for Fiberon grooved profile composite decking. Exceptionally helpful for designing router jigs. I've tested this with the "Weekender" series, which should be the same as the "Good…
Templates for routing holes in decking so that electrical cords can be passed through. The hole size after routing with the recommended bit will be 10mm. Designed for a 1/4" diameter straight router bit. A cheap Ryobi bit worked fine. For…
Long story short, my deck has a few massive screws over penetrating by several inches. Knowing me, I'll poke a hole in my head or decide I don't need depth perception....these solve both of those risk. I eye balled the screw size but I…
This model consists of cross-shaped and T-shaped spacers designed to maintain a uniform 5mm gap between wooden decking boards during installation. The geometry features vertical fins that fit between the planks to define the spacing and…
Templates for routing holes in decking so that electrical cords can be passed through. The hole size after routing with the recommended bit will be 10mm. Designed for a 1/4" diameter straight router bit. A cheap Ryobi bit worked fine. For…
Long story short, my deck has a few massive screws over penetrating by several inches. Knowing me, I'll poke a hole in my head or decide I don't need depth perception....these solve both of those risk. I eye balled the screw size but I…
A funnel for the Wagner sprayer bottle to avoid spilling paint when pouring it in.
Spacer block to help you build a wooden deck with constant spacing between the boards for a well-ventilated and even wood board deck With big numbers for easy identification of the right number. Fixed floating parts inside number 6 and…
I'm very happy with the discrete hatches for storage in my porch and wanted something correspondingly discrete to open them. These ones don't even require any screws - just stick the handle in from the front and put the wedge in the slot…
Simple alignment tool for decking I made as I couldn't find any locally that weren't overpriced. Should be printed in PETG for the extra strength with at least 4 perimeters. Mine were printed using the standard Prusa settings tweaked to…
Simple decking spacer. I used 5 when I installed decking in my garden recently and they worked well.
These little anchors grip between decking with 10mm spacing. They have strap loops at the top to tie things to. I use them to secure a parasol base to my decking which otherwise tips up when it's windy. I use them in PLA, but they also…
this little bit of kit will help with even spacing of the boards, you can choose whether you want 5mm or 8mm spacings. I recommend printing plenty of them to allow for different board lengths version 3 widened centre bar, after trying…
