30 modeli
Coaxial thread levelling feet with octagon head - each side changes height by 0.25mm (2mm/360°). pre rendered heights for download: 10 (thin bottom) 15 20 30 50mm Extending about ⅓ of length.
Ikea recently introduced very nice, cheap and useless containers. However adding these distancers/legs into a corner allows conversion to stackable containers Print settings: sharp corners need time to cool down so either print 4 at once…
This is a z limit spacer for the Anycubic Photon D2 DLP. It allows you to effectively raise the height at which your z limit triggers. I have included two sizes, 2mm and 2.5mm. I used the 2mm spacer on my Photon D2 with a WhamBam flexible…
The Social Distancer allows you a fun way to keep the public (or your little bro) at a healthy distance, and do some target practice to help cope with quarantine. Features: Simple, three-piece design Easy no-glue assembly Range of up to…
Keeps your dishwasher door a bit open The door should be ~55mm wide. If the gap slightly to large for your door, you can use felt or scale it down a little
As Aqara U200 doesn't have 10mm diameter adapter, and especially for my EVVA 4KS deadbolt with hole for retainer - I had to model it by myself. Made few iterations before to gain perfect for my purposes. * By the way, it should also fit…
These tile holders are designed for installing wall tiles where a clearance is needed between the lowest tile row and the floor. The height offset can be adjusted using the M8 screw located in the center. Printing Print the tile holders…
Outdoor tiles require gaps. As our stone tiles are wider on the bottom, it wasn't easy to hold a good distance for all tiles. So I designed these distance holders, They are 2.5 cm deep, go 3cm in all directions. Gap Top: 1cm Gap Bottom:…
Extends the roller to accommodate large 5kg rolls. Should still be compatible with most rolls on the market. Added a bearing distancer if you want to tighten the original bearings without adding friction. Be aware, I removed the bearing…
CD60 Spacer/Distancer The whole length of the distancer is 40cm and the inside spacer is 34cm I made this model back in 2024, I don't really remember all the measurements thus I'm attaching STEP file for you to modify it for your own use…
No special print settings required.
Most filament rolls are narrower and do not stay in the middle of NaNO3's holder. Snap on distancers to center the roll. Print with PET for permanent elasticity (PLA loses tension over time). For other sizes use the step-file in a 3d…
The thread should be made with a tap or screw/nut
Keeps your dishwasher door a bit open. The door should be ~60mm wide. Works well with V-Zug Adora models. Print Instructions Fiilament: TPE Nozzle: 0.6mm Layer height: 0.3
don't you just hate it when you have to replace the whole wc board 'cause those plastic distancers pop out and get lost, or break up, crumble... freecad source available, the values are not in separate table but there are 2 sketches in…
📝 Description: This simple spacer is designed to keep your desk at a fixed distance from the wall. It’s perfect if you want to move your monitors farther away from your face 👀, create extra space for cables 🔌 or a power strip ⚡, or…
Parameters wall_to_pole min. 10 mm height pole_dia min. 15 mm wall_grip_angle min. 1°
useful to cut electrical wires for perforated grid boards
This is a spare distancer (used to keep the top of the hood stretched) for the "Elegant Bee" beekeeping suit. Normally, it is stored in the small front pocket. When the suit is worn, it is inserted into the top part of the hood to keep it…
V2 of a Distancering for eVicVTC Mini mod. Prevents wobbling of a 22mm atomizer. Smaller throughhole fitting to atomizer for better centering. V1 see here:
Most distancers for painting have a spiked tip. This means, that the weight of your component is concentrated at a single point. These distancers have a slim, but long edge to reduce the load by distributing it along the edge-line. This…
AMS Lite Wall Mount Distancer - not to hit wall with spools . Original print was too short - I got this knowledge after printing and putting it on a wall. It was easier to make a distancer than to print it once more in a longer version.
Distancering for eVicVTC Mini mod. Prevents wobbling of a 22mm atomizer.
# Window Distancer (with cherub) A 3D-printed magnetic spacer for double windows. It keeps the inner and outer window **60 mm apart** to prevent lever break the glass. A magnet pad sits against one window and the leg with a round knob…
V2 of a Distancering for eVicVTC Mini mod. Prevents wobbling of a 22mm atomizer. Smaller throughhole fitting to atomizer for better centering. V1 see here:
As Aqara U200 doesn't have 10mm diameter adapter, and especially for my EVVA 4KS deadbolt with hole for retainer - I had to model it by myself. Made few iterations before to gain perfect for my purposes. * By the way, it should also fit…
CD60 Spacer/Distancer The whole length of the distancer is 40cm and the inside spacer is 34cm I made this model back in 2024, I don't really remember all the measurements thus I'm attaching STEP file for you to modify it for your own use…
Coaxial thread levelling feet with octagon head - each side changes height by 0.25mm (2mm/360°). pre rendered heights for download: 10 (thin bottom) 15 20 30 50mm Extending about ⅓ of length.
