Liczymy pasujące modele…
The box is based on my parametric “ Rugged Box ” and holds up to three DMT 6" diamond whetstones and the holder you can find here: https://www.printables.com/model/610107-dmt-6-diamond-whetstone-holder Support my work For non-Prusa parts…
Just print and add some rubber feet. A box to store three whetstones and this holder: https://www.printables.com/model/610119-dmt-6-diamond-whetstone-holder-box Support my work For non-Prusa parts and filaments, check out 3DJake (…
This design to be used with FNIRSI DMT-99 Multimeter. It could be used with other multimeters. Inside diameter for multimeter is roughly 75t x 79w x 28d mm. The lead holder is detachable from the main body by 3 magnets. They are roughly…
This is a mostly printable device for sharpening knifes using DMT Diamond stones. It uses hardware I had laying around so it's more or less built around those parts. Parts needed: DMT Diamond Stones Linear rail - in my case HIWIN from an…
Holder for Fnirsi DMT-99 Multimeter, gridfinity size 2-1-9. Loose fit for the MM. Two slots for multiconnect on the backside to put it up an HSW. I glue my gridfinity feet on after printing the bins, you can also use the holder without…
This is a box with lid designed to hold 12 KME or DMT 4 inch sharpening stones. There are two stl’s for the lid. One plain and one with writing on it. I’ve printed the box twice, once in PLA Pro and once in PETG. Neither required support.
This is a wall support for my multi-tool Makita DMT52 I glued it with epoxy to my wooden wall. You can remix it to add screw support, or ask me if you need it. The multi-tool can be inserted from the front-bottom with an upward movement…
Simple holders to make using DMT DiaSharp sharpening stones easier. The smaller one fits 0.8" x 4" (22mm x 101mm) sharpeners and the larger one fits 2" x 6" sharpeners (51mm x 153mm) sharpeners. This model includes space for a 1.5mm thick…
Knife sharpener for DMT Mini Diamond Whetstone 70 X 25mm Model is split for easing, no-supports printing. I attached the “clamp” stl to the “stone_holder” stl using 1.75 filament and super glue (CA). I did have to clean the holes with a…
Shell for standard full sized foam darts, compatible with the DMT lever-action blaster.
Simple molecular structure of DMT and two structural analogues, which are all powerful psychedelics, 5-HO-DMT in particular, can be found in the human body in small amounts. In the Fusion 360 file you can change dimensions, thickness and…
A holder I made to be able to attach the Diasharp Diamond stones to a board while still being able to take them out. Some of the stones have pretty big tolerances so while one fits perfectly the next might be a snug fit, so maybe print…
Printed at 0.20mm layer hight with 10% infill and i was able to print it without any supports. I used PETG but other materials will probably work aswell. Printed on Creality Ender 3 V3 SE.
Case for the DMT 70mm Whet Stone set with a cutout for holding one when in use for sharpening. This model is print-in-place and does not require any supports. Snap off the pre-support fins in the cutout and gently wiggle the two sides to…
Designed for holding 3 DMT diamond stones for sharpening purposes or storage. After watching videos on plane blade sharpening, seemed like 3 blocks (coarse, med, fine) was a good setup so I made the block to keep them secure in use.…
Years ago, I bought a DMT diamond whetstone to replace a worn out ceramic whetstone. Since then I’ve been happily using it for freehand sharpening of tools and knives. It is hard to get consistent angles when freehand sharpening. So when…
Designed for holding 3 DMT diamond stones for sharpening purposes or storage. After watching videos on plane blade sharpening, seemed like 3 blocks (coarse, med, fine) was a good setup so I made the block to keep them secure in use.…
I have never bothered to buy the official base as found it to be flimsy and hollow. After long time of improvising I have decided to design my own bulky base to hold sharpening stone steady. There are three parts in my design. Bottom pad…
A gridfinity bin for the DMT D2K Mini Diamond Sharpening Stones 3 pack (*https://a.co/d/jlBTein) the bin measures 5x1 units and is 4 units tall.
This little nub is press fit into the ADMAGB3476 and gives you spot to connect it to something else, like the ballscrew I used in this prototype. Granted, a pretty specific application... but if you need to connect to the ADMAGB3674…
Doing a prototype for the ADMT4000 multi-turn magnetic sensor, I needed to mount the eval kit in a way that would let it sense the magnet turning at the end of a ballscrew. The model here is very specific to my setup, but I've included…
Add some small rubber feet underneath the print for extra grip while sharpening.
