Liczymy pasujące modele…
Printed lying on its face. 3 walls and 3 top/bottom. 15% grid infill. Very solid, but the pin version isn't great imo. For V2 you will need supports as shown in the photos.
Required parts: 2x M5 x 16mm 1x M3 x 12mm 1x M5 Washer 2x F695 Bearings The washer should go between the top bearing and the printed adjuster. Snug the M3 x 12mm screw, but do not tighten it. The bearings should spin freely. If you don't…
Clips on the Gantry, Prints in 2 pieces, there are 2 ‘keys’ one is slightly larger, find the one that fits best and press the 2 halves together over the key. if you print with supports, they will go into the keyhole, but they do dig out…
Remix of parts of two main board boxes. This is set up to hold SKR Mini E3V3, RPI, U2C Canbus and LM2596 Buck Converter Mount holes are at 2.80mm so should self tap M3 Holes on the right of the case are for M5 Heat Inserts RPI fan is for…
Camera holder for Creality Ender 3 V3 SE/KE printer. With attachment for the original Nebula pad holder.
Added a cutout to the outside wall to make it easier to grab things out of the tray.
When clipping on to the gantry, put the tiny clip edge on first, so that the bar is angled downward and hinge it upward to pop the rear hooks over the top. also, the keys still seem pretty tight, you might want to scale them down a couple…
Updated model with improved rigidity and printability
I was wanting to upgrade the extruders on my Original Ender, Ender 3v2 Neo and CR-10 Smart XX, and found the extruders from the Ender 3v3 CoreXY to be a sufficiently fast extruder. Purchased a few and then realized there weren't really…
It goes on pretty snug right bellow the pressure sensor, maybe you might need to sand it down a bit for a perfect fit but it's better this way so it goes on as snugly as possible reducing vibrations as much as possible. There's a 3D…
The end of the line.
Okay, so I didn't really design it from scratch, but I managed to get my original Ender 2 Pro spool holder test piece to ensure the screw holes are correct. I used the side mounted spool holder from @CHEP for the Ender 3 printers, if you…
Cr10s pro v2 conversion to Skr Mini E3v3 board. BOM 5 x M3 heat inserts 4.5/5mm width
It was a bummer for me to see how is the print doing even with led strips on the edges of my box for the printer. So I came up with this. It just hooks on the X axis motor. I recommend to print it in PETG because of the heat, PLA will…
Model is ugly and was put together in tinkercad in a few minutes. All credit to original creator. rook 2020 electronics back pack orange pi 3 lts and pico by human | Download free STL model | Printables.com
I had a problem with crochet on original model, it was weak. So, after I printed spine cable chain I realise that top part of chain shoud be connected to nebula support, so here we go) but still need to use plastic clamp for stable at…
It's pretty self explainatory really, needs supports.
E3V3SE-REVERSE BOWDEN. V1 = NO FITTING & NO CABLE CLIP V2 = NO FITTING & WITH CABLE CLIP V3 = WITH FITTING & NO CABLE CLIP V4 = WITH FITTING & WITH CABLE CLIP
Mounting adapter plate to allow the BTT RaspberryPad5, 3D printed backplate to mount to the original Ender 3 V3 SE screen mounting bracket peg interface. This allows you to mount your Klipper host running KlipperScreen (or anything using…
Complete redesign on fusion to fit my printer as the frame was fatter. I loved the original design, but it fell short in being compatible. Print it PETG minimum.
Mounting adapter plate to allow the BTT RaspberryPad5, 3D printed backplate to mount to the original Ender 3 V3 SE screen mounting bracket peg interface. This allows you to mount your Klipper host running KlipperScreen (or anything using…
Prints in an hour and a half No support Only 1 color change I used eight 10 x 2.5 mm magnets for this they hold very well Push down on the bottom of the nozzle to remove it from the box
PTFE tube remover E3V3 K1C This mod is very useful for making your life easier.
You will need: 4 M3X40 Caphead ( to close the case ) 4 M3X20 Caphead ( for the fan ) 5 M3X12 Caphead ( for mounting the board to the case ) 4 M3X6 Countersunk ( for mounting the DIN rail clips to the case ) 17 M3 Nuts (nylon lock is…
So this is an update of my original model from https://www.printables.com/model/240112-btt-skr-mini-e3-v3-case , as the changes are getting a bit messy to include all the variations of the case in that post. I have changed a few things. I…
Prints in an hour and a half No support Only 1 color change I used eight 10 x 2.5 mm magnets for this they hold very well Push down on the bottom of the nozzle to remove it from the box
just a basic enclosure designed to be printable on 225mm^2 or larger print beds. top and bottom print separately. Top held to bottom by m3 screws, designed for 40mm cooling fans. models used for basis credited below.…
Wanted a unique Toolhead cover for my Ender 3 V3 Plus. Still a work in progress
This design allows you to mount the BTT 35 e3 v3 LCD onto a flat surface.
This was made to hold a camera above the Nebula Pad on a CR-10 SE or Ender 3 V3 KE. Note that this will not work with the stock mount. It was designed to be used with the mount that I created here . It has a GoPro style connector which…
