Liczymy pasujące modele…
Printed using PETG, but any material should be fine. You'll need a little bit of flex to get the latch onto the corresponding pins of the hinge. On the hinge, enable “Supports on build plate only”. On the latch, I used paint-on supports…
Wydruk około 0,14 €–0,17 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A bracket to hold the Brother E550W label printer (p-touch system) on an Ikea Skadis toolboard. Should be self-explanatory. Add two rubber domes at the back (bottom) for extra stability. Or edit the model to add a lip there.
Print this out of ASA or ABS. Insert fits the Harbor Freight Apache 550 Cases here: https://www.harborfreight.com/550-weatherproof-clear-case-56378.html Their SKU is: 56378 Use M3 Self-Tapping screws to mount a RAK19007 Baseboard into the…
Designed exclusively for the TP-Link Archer BE550 Wi-Fi 7. Converts the standalone router into a rack-mountable unit for 10-inch rack Orientation: Print in an orientation that maximizes strength along the mounting flanges.
See the original post that inspired this here: https://mbworld.org/forums/w213-amg/813377-flimsy-cupholder-solved.html Nothing special printing, just make sure you have 8 spacers for each ‘corner’ of the cupholder. I used vegetable rubber…
Print in whatever you want, PLA+ is plenty strong and add whichever 2mm T-Nut design you like the best. Align the 3 T-Nuts with the slots in the Skadis board and then spin the machine screw heads to lock them in place.
Tested with Brother E550W, should work with similar models.
A bracket to hold the Brother E550W/PT-H500 label printer (P-touch system) on a Multiboard wall. Note: This will not work with the Brother P-Touch E560 which is slightly larger. You need two or four Multibuild Lite Fix Points to attach…
Landegestell in Keilform. Hintere Halterung ist etwa 12mm höher als vorne. Dadurch wird die Gefahr mit der Heckfinne beim Landen einzuschlagen verringert. Wedge-shaped landing gear. The rear mount is about 12 mm higher than the front.…
Nachmodellierung des Höhenleitwerks Remodeling the horizontal stabilizer
Nachmodellierung des Seitenleitwerks / Finne Remodeling the vertical stabilizer / fin
Thunder Tiger Raptor E550/E620 Riemenscheibe | Pulley PV0379 Die 14mm-Bohrung sollte mit einer Reibahle 14H7 nachgerieben werden. Dadurch passt die Riemenscheibe perfekt auf die Nabe des Sperrlagers. Replica of the original pulley…
Modellierung der Heckrohrschelle Modeling the Rear Pipe Clamp
Nachmodellierung der original Grundplatte PV0075 Remodeling of the original PV0075 base plate
Printed using PETG, but any material should be fine. You'll need a little bit of flex to get the latch onto the corresponding pins of the hinge. On the hinge, enable “Supports on build plate only”. On the latch, I used paint-on supports…
Wydruk około 0,14 €–0,17 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A bracket to hold the Brother E550W/PT-H500 label printer (P-touch system) on a Multiboard wall. Note: This will not work with the Brother P-Touch E560 which is slightly larger. You need two or four Multibuild Lite Fix Points to attach…
Print this out of ASA or ABS. Insert fits the Harbor Freight Apache 550 Cases here: https://www.harborfreight.com/550-weatherproof-clear-case-56378.html Their SKU is: 56378 Use M3 Self-Tapping screws to mount a RAK19007 Baseboard into the…
