Liczymy pasujące modele…
I hated that some of these tubes of E6000 come with large nozzles, and I needed something more accurate for dispensing into cracks and such. Unhappy with the couple of nozzles I found online already that had different modeling defects and…
Never lose a drop of e6000 again! This thing adapts the e6000 nozzle to a luer lock so that you can load a glue syringe easily. To use: Screw the luer lock end on a syringe Jam the nozzle of e6000 in the other end Squeeze the e6000 tube…
First of all a big thank you to JeepingJohnny and all the predecessors in making these great models. With these models you can use E6000/S80 needles which are much easier to get in Europe. I had some issues with the rounded groove design…
Wall mount for Shimano E-Bike battery charger. Print two of the brackets per charger. Remove four T10 screws from the four corners of the charger. Insert the pins of the printed brackets into the holes where the screws came out of and put…
I needed a wallmount for my E-bikes charger. I found a model here for another charger and i remixed it to fit the EC-E6000. The mount can be fixed with two screws, or with double sided tape like I did it on the side of a cabinet. I…
A larger tip version of the parent design, this one has a ~5.3 mm diameter hole instead of ~2.3 mm diameter hole. Print as with the parent.
Nozzle pin for E6000 adhesive precision tips. Use this to clear out the adhesive from the tip/nozzle after using the adhesive. Physical (printed) measurements: Pin length (circular): 32mm Pin diameter: 1.3mm Allow it to cool before…
This is a replacement hook, ment for the E-Way E600 and E600MAXs folding handle, but it can also be used on other E-Way electric scooters, as well as many other scooters, but here you would need to try it out. All you need to do is to…
This is a replacement cap for a 3.7oz/109ml tube of E6000 adhesive. I recommend printing in TPU for a good seal. I originally printed this in ABS, and it eventually became brittle and cracked (perhaps from the solvent in the glue?). The…
a simple e6000 holder for the hex peg board
Here are 2 models of the rings, one reinforsed and one as original
Super Simple Design. So simple that I almost didn't even upload it, but it's been so useful for me, as I like to use the smaller tubes of E6000 because I can never seem to use a whole large tube before it dries out. Hope this can be…
Store or charge your Shimano BT-E6000 battery hanging on the wall. Mount with 4 screws that are appropriate for your wall material. I printed this in PETG material and mounted it using 4 screws. Other material may work as well. Invalid…
Simple bracket for the Shimano Charger so it can be mounted on a wall. Made to fitt the EC-E6002 Charger Printed with 4 wall loops and 25% infill.…
When the display is removed form the bike, a cover can be used to protect the electrical connections as well as avoid scratches on the surface, if put in a bag. The lid is locked in place when closed by bumps on the bottom part. There are…
this is a simple design to simplify the installation of a prop adapter on the DJI e600 motors and allow the use of any p
This print mounts to your Shimano EC-E6002 charger using two of the original housing screws. It provides a ring which can be used to lock the charger to a bike using a bike lock or chain enabling you to charge in public places without the…
This is my second entry for the Cooler Master FreeForm Playground Contest, and several additional designs are already in development. The models are fully custom-designed for the MasterFrame 600, a highly modular chassis built to…
REMIX von https://www.thingiverse.com/thing:7142931 und https://www.thingiverse.com/thing:5141294
Simple bracket for the Shimano Charger so it can be mounted on a wall. Made to fitt the EC-E6002 Charger Printed with 4 wall loops and 25% infill.…
The cap of my E6000 tube gets worn down way before I run out of glue. Now you can print a new one with improved wing grips! There is no threading, so be sure to twist it on hard the first time so the threading gets indented into the cap.…
my brother embroidery machine (the SE600) does not have a stand/space to hold large thread which is quite troublesome, so I made one. You will need to glue a ball bearing wheel so that it can spin freely. I got the bearing from an old…
