34 modeli
A top mounted belt tensioner for a FolgerTech Delta Printer. This may fit other 2020 framed Delta printers too. This allows for about 7mm of adjustment travel, and raises the idler pulley about 15mm higher. NOTE : You will likely need…
I did my best to make a simple mount for the Hemera extruder on the FT-6, but this needs to be done in order to make it successful. Step 1, attach the PCB with M3 nuts and M3 x 14mm screws to the back mount with the printed spacers. Step…
Similar to some other FT-5 spool mounts, but with a couple of differences: I designed a horizontal lip to hold the weight, rather than relying on the bolts & T-nuts to support all of the weight. Chose to design this one to work with a 1"…
I've been working on this for about 8 months. Finally got around to printing all the parts and putting it all together. Lots of tweaking and reprinting. Now I have it almost the best I can do. Still have a few things I would like to…
i bought a folgertech ft-6 and after a few prints i noticed that the original belt idler pulleys where not straight and where destroying the idler wheels. so i have designed this simple part that bolts to the frame and with a longer m5…
Solid Y end-stops for the Folgertech FT5. These are meant for use with sensorless homing (like on the TMC2209 drivers), and give the bearings something solid to run into. I had issues with my two y motors getting out of alignment with a…
This is to sync the 2 Z axis motors together on the FT5. The front spindle mount plate uses the stock screws and channel nuts for the bottom and 6-32 screws to attach front bearing spindle mount to the top and bottom of the spindle. use…
Front panel replacement for the FT-5 to use the Full Screen Graphics display. Nice drop in replacement. Category: 3D Printer Parts
This is a remix for Paul (Where Nerdy is Cool!) since he preferred the M3 screw to cut its own threads in the stepper mount.
Update 11/15: Switched to a BMG vlone and added a compatible part cooler blower channel for BMG+V6+Volcano. Piezo leveling is still working great and I have switched back and forth between the Aero and BMG with almost no adjustment.…
I wasn't especially happy with the stock mechanical switch solution on this printer, so I bought a couple of these: https://bit.ly/2maUa3B and started designing the mounts you see here. This replaces the Y axis stepper mount ACM part and…
Pretty basic to print. Use supports to get screw head areas, obviously the big flat side down. I printed mine at 50% cubic infill for the best multidimensional bend resistance. This has been tested and works great. Category: 3D Printer…
Made some mounts for a cable chain to be mounted in the FT-6 printer and hold the bed AC and thermistor wires. Using basic amazon 10mm X 10mm cable chain. Print Settings Printer Brand: Creality Printer: CR-10 Mini **Rafts:** No Supports:…
I wanted to be able to customize some of the parts on this printer since I am using different electronics, power supply, etc than what came with the printer. These are the basic shapes with bolt holes for basic assembly. I included the…
This is a mount for a print cooling fan for the Folgertech i3 2020 3D printer. It fits one of the common 12V 50mm radial fans with a 15x20mm outlet and provides a low restriction duct and print cooling nozzle. Mounting the duct will…
UPDATE 4/27: I still see a lot of folks downloading and liking this carriage. I'm glad people are finding it useful and it's still a great replacement for the stock carriage - especially if want to maintain compatibility with other parts…
!!!These items are still WIP!!! UPDATE 1/31: Added FT4, FT10, and FT10/FT4 Merged copies that fit the new idler design. I do not have the bolt and bearings to test with so feedback or suggestions are welcome. UPDATE 11/20: Added a number…
Update 11/13/2016 - The topless versions require a new 'female' base. Added female and male bases. I've now installed the open-face chain and printed a couple test prints. If you want a complete, open-face chain I would suggest printing…
Original, Stronger, and Dual Spool mounts for Folgertechs FT-5 3D printer. Print Settings Printer: FT-5 R2 Rafts: No Supports: No Resolution: 0.15mm Infill: 15% Filament: Doesn't Matter Doesn't Matter Doesn't Matter Category: 3D Printer…
This is a kit to help with the noise in the parts in Ft-6 prints The problem I ran into is that the Two motor breakout board for X axis seems to backfeed power between the two motors and adds noise in the print and limits the speed This…
This is for the side electrical panel in the back of the FT-6 the part # is BFP-12 There is a cut-out for the 110v plug and a 80mm fan Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 Plus Rafts: No Supports: No…
This is made to use uxcell Drag Chain Cable Carrier Open Type that is 10mmX11mm for its ease of cable install and is on amazon Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: No Supports: Yes Resolution: .2…
This is a Remix form Blinkingsun's ft-6 Y-carriage the changes i made are: Y-Carrier Increased size for belt screw holes for m3 and put m3 nut cut-outs in Belt guide Increased size for belt guide screw hole for m3 and put m3 square nut…
This is for the side electrical panel behind the lcd on the FT-6 the part # is BFP-14. I left it as a blank panel for you to add the fan/lcd/controler you want Print Settings Printer: Ft-6 Rafts: No Supports: No Resolution: .2 Infill: 50…
I printed at .2 layer height with supports with top distance of .2 used the factory screw and t-nut Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: .2 Infill: 25 Filament: amazon PLA Black Category:…
I remixed the backplate of the eva v3.0 to fit the Folgertech Ft-6
This is a modification from the original by Morskipas. I extended it to allow for the longer body of the E3D Titan V6 mounted on the 713Maker.com bracket. I will be modifying this as needed. Assembly is easy. Print with orientation as…
Adjustable z endstop system for the Foglertech FT-5 printer. I have the r1, but I imagine this would fit on the r2 as well. This eliminates the need to physically move the entire endstop up and down when trying to dial in the z endstop.…
This simple mount holds the generic LCD panel to the top of the right z-axis motor. You will need a little longer m3 bolts for the stepper motors, and you will need 3 fairly short m3 bolts to mount the 2004 LCD plate itself to the mount.…
The FT-5 LCD panel has a crushable stud for the knob. (I am not sure of the technical term for it.) You will need to push a screwdriver into the stud to widen it just a bit and then this will fit nice an snug on the LCD panel.
To replace, or serve as, the acrylic motor/rod brackets that come with the FolgerTech 2020 Prusa i3 kit. Category: 3D Printer Parts
This fan housing prevents fan from blowing to the extruder's hot end area. This way the extruder heatsink stays cooler and the tip temperature is much stable without unneeded airflow. Just put this sleeve between the fan and original fan…
Finally, after making spring-adjustable bed mount ( http://www.thingiverse.com/thing:1102612 ), I decided to get rid of Z-probe and redesigned the E3D mount for second 40mm fan. It's adjustable, easy to maintain nozzle. It looks flimsy…
This is a modification of thing http://www.thingiverse.com/thing:798863 by tirefoamcan to make it easier to print and work with the Folgertech 2020 i3. Category: 3D Printer Parts
