Liczymy pasujące modele…
Cockpit Kit: Freewing Models R/C 90mm EDF F-18c Hornet This is a 1/11th scale cockpit kit designed for the 90mm EDF Freewing F-18C Hornet Fighter Jet. Included are the STL Files, a printed parts list, detail photos for painting, assembly…
This bracket fixes the extended nose wheel in an AvantiS RC model from freewing. It stabilizes the landing gear. The component is hollow inside and has an edge to glue. The distance of the bracket between nose wheel and model is 15mm and…
Nose landing gear doors for Freewing Avanti S 80mm EDF. Haven't tried printed it yet. Would like to hear your print experience, successes, failures, slice & print set-ups, tweaks/ remixes, improvements, etc. Category: R/C Vehicles
Wing Fence for Freewing Avanti S EDF RC Jet I have printed in PETG and is flexible and does not break A file for milling is also included
You need O-rings ID33x2,5 mm, ball bearing MR 128 8x12x2,5 and MR 128 8x12x3,5 ZZ. A servo: MASTER Servo S308. The Cam may need to be adjusted in size for optimal balance between brake force and the torque of the servo. The servo isn't…
This is not my design but a free download from Freewing RC Planes. Print Settings Printer Brand: Up Printer: Up Plus Rafts: Yes Supports: Yes Resolution: .15 Infill: 5% Filament: Fillies ABS White Category: Models
These parts are designed for the FreeWing Fa-18C 90mm EDF. These are scale parts to replicate the forward fuselage vents, louvered vents and antennae. You MUST preform ‘foam surgery’ for many of these parts which will violate MotionRC and…
Spektrum AR8020T receiver and blue box support without glue Category: R/C Vehicles
3D printed wing tanks for the L-39. I bought my plane 2nd hand and it had the pylons installed, but was missing the tanks, so I designed them in OpenScad. Printing I printed the front and back parts of the tanks in LW-ASA (foaming) with…
These missile rails are an option for the Freewing F-18C Legacy Hornet 90 mm EDF. These screw onto the wingtips in the OEM location. I drilled and tapped the OEM mounting holes to fit 2-56 Nylon Countersunk screws, but you can use…
Nose Gear Brace for the Freewing Avanti S 80mm v1 and v2 (no difference). Don't spill epoxy on the gear mechanism ! Put a wad of kitchen paper or something similar underneath. Then sand the piece on the sides, apply some epoxy on the…
Print 2 pieces and install behind each main landing gear strut and alongside fuselage as illustrated in the picture. Print the Gear Mechanism Reinforcement Bar in carbon infused filament for optimal strength. Put them all the way down to…
A few weeks ago, I was flying my Freewing Rebel V2 that I'd purchased from MotionRC, and I “dumb thumbed” the landing. I tried to throttle up, bring the plane around, and come back, but I didn't have enough power to carry it around to the…
These nozzles should be printed using LW-PLA. At 50% extrusion rate, two perimeters and 10% Gyroid infill these are slightly lighter than the original nozzles. Need to extract the ball joints from the original nozzles and glue into the…
This replaces the stock battery tray in the Freewing F-22 70mm EDF to allow the routing of the servo wires through the sides and under the tray.
Freewing SU-35 Nosegear Brace, install as in the picture
This is a servo reinforcement for the Freewing F4-Phantom elevator servo. You can glue it simply over the servo, so this servo will stay very taff on its place. Print it with PETG or PLA. No need to get strong infill. 2 outlines are enough.
Freewing SU-35 Main Gear Brace - Print 2 Pieces, see pictures on how to install.
Mounting plate for the receiver in a Yak-130 from Freewing, possibly also suitable for the model from FMS. As a receiver I have used an Frsky Archer SR6. Mounting advice: To glue the mounting brackets correctly, screw the plate to the…
Freewing avanti front right door. left door - mirror
Mirror for left and right
Most commercial kits are designed for larger inrunners, making secure and centered mounting difficult for the smaller 64mm unit. Key Dimensions: Outer Diameter (OD): 63 mm (Designed for a tight friction fit in the air duct) LED Inner…
FreeWing B2 Wall Mount designed around normal 16" stud placements
There are LED afterburners for RC model jets which imitate the exhaust jet of an original turbine. The LEDs are screwed onto the motor of the impeller. If the LED fits the holes, it can be mounted directly. If not, there are adapter rings…
mounts to wing soft hadles with 5 cable ties It's created for a freewing air v2 model (2021)^ but you can customize it for yours wing handles. In my case I have a ~150 mm diameter of my handles, in yours, you should to measure ~ diameter…
Horizontal stabilizer Category: R/C Vehicles
This is a receiver shelf for the Freewing T-33 Shooting Star. It is designed to go under the cockpit / hatch between the EDF inlets, behind the Blue Box and above where the wing connectors enter. Placement is not too far off CG and if…
Adaptateur conçu afin de réparer une turbine avec porte hélices de FW190 Freewing après case de l'insert 6 pans de 9 mm.
Replacement for the original canopy lock for the F9F model
