Liczymy pasujące modele…
Hi, thanks for downloading my file! I made this suppressor/silencer for my Novritsch SSG24, because the one Novritsch sold on his website was a bit too expensive for my taste. How it's made This silencer is made up of three easy-to-print…
Remixed the design by ParabolicTech to work with the factory screws and added recesses for M4 hex nuts Print instructions Category: Parts Summary Remixed the design by ParabolicTech to work with the factory screws and added recesses for…
A simple and sturdy mount for the Sonoff Zigbee & Thread Dongle Plus (MG24). This holder provides a snug fit for the dongle and includes enough space to accommodate the included USB extension cable for better signal placement. There are…
Was sick of the non-adjustable stand so I bought a VESA mount for my monitor but adapters were around $30 on amazon so decided to make my own. The VESA adapter is designed for the MSI optic G24C however may work for other monitors.…
Vesa adapter plate for Acer G247HYU. Uses the metal bracket from the original stand that clips into the bottom of the monitor. No extra hardware needed. Use the screws that normally hold the tilt mechanism to fasten the bracket to the…
Dies ist eine Kleine Halterung für die Sonoff Dongle Plus MG24 Montage Möglichkeiten Schrauben, Kleben oder mit max. 6 Magneten 5 x 3 mm die Aussparungen schon auf der Unterseite vorhanden. Diese Halterung ist so konstruiert dass das…
The original fuel cap of my edge trimmer broke and the replacement was too expensive so I modeled a new one. Original part number: 51049-2091. Freecad source included.
XIAO MG24 is an ultra-low-power wireless development board based on Silicon Labs' EFR32MG24 SoC, featuring a high-performance 78MHz ARM Cortex®-M33 core. It‘s Matter® native over Thread® and Bluetooth® Low Energy 5.3, all supported by the…
Quick connect / lock mechanisms are a blessing, if you travel a lot with your gaming setup (LAN parties). This adapter plate allows to quickly swap between the original foot and a VESA mount so you don't need to unscrew the monitor every…
Simple 3d printed adapter to use the DVS8 Bioc NVG with dovetails mounts. Required Parts: 2x M4x4 6.3mmOD heated Insert (like the ones from CNCKitchen) 2x M4x8 Screws
Adapter for mounting the PNV-57 NVGs to the Wilcox G24 helmet mount. It was designed in Inventor and should be easily modifiable. Made to be used for playing airsoft. Uploaded simplified version if you have printing problems or want the…
Had this monitor laying around and decided to create a vertical stand for it. Since the back of the monitor is curved at the bottom i created two pieces for the best fit. Since it doesnt have a vesa mount, it wouldnt fit with vesa stands…
This is a remix from https://www.printables.com/en/model/223063-msi-optix-g24c-vesa-adapter-100x100/files I could not find a complete file I modified this one and it works perfectly. The curved monitor has a different mount than the…
Mount your Arris TG2482A securely and cleanly to any wall with this custom-designed 3D printable bracket. It’s made specifically to fit the TG2482A modem/router and holds it snugly in place, keeping your device off desks or floors. ✅…
I bought the SSG24 and was a bit disappointed that I could not attach my favorite scope because the cutout was a bit too big for the fixations. I made this rail to go on top of the original rail, so you get to use the full length of the…
Layer: 0,2mm, infill: 30%
The SONOFF Dongle Plus MG24 is a USB device that comes without an additional holder. If you want to mount this dongle properly, you have to construct a holder yourself. I have designed a holder for the Skadis wall from Ikea. I also…
140mm and 240mm
Snap-fit enclosure for the Silicon Labs XG24-EK2703A / EFR32xG24 Explorer Kit. The EFR32xG24 Explorer Kit is a small form factor development and evaluation platform based on the EFR32MG24 System-on-Chip. The EFR32xG24 Explorer Kit is…
This is a WIP. This print will add a faceplate to a Arris DG2470 Cable modem so you can rack mount it. It has a window so you can still see the LEDs on the front of the cable modem. This will be my first upload and first functional 3D…
The slip clutch provided on the PTO shaft for a WG24 stump grinder has to be set for the horsepower rating of the tractor. The slip clutch adjustment consists of tightening the springs to a given pre-load based on horsepower (HP). This is…
Holder for the Sonoff MG24 Stick. This was made completely by AI (Anthropic's Claude). I have no idea of the quality of the model and the scad file. Please be aware of that. Printing though worked fine for me.
This holder is used to mount Sonoff Plus MG24 to the top of 35mm tube which holds monitors
I recently purchased a pre-assembled Geiger counter kit from Electronics Goldmine and noticed that they didn't have an option for a housing for it. So I thought it would be a fun Tinkercad project. This is a simple rectangular box with a…
Miele Dishwasher Wheele Clip The upper drawer for this dishwasher sits on some drawer slides, which roll on two wheeles. Those are clipped into some pins, which are mounted on the machines inner wall. These wheeles are clipped onto the…
This is a shelf for G24d-2 and G24q-2 lightbulbs. Pretty particular ones (they were FL bulbs with external ballasts) but I needed them so I did. The sockets were reverse-engineered from scratch, as nobody even made a technical drawing of…
I made a thread mesh monitor and part of it uses a Seeed Studio Xiao MG24 running the OpenThread RCP (“radio co-processor”) firmware. The issue I have is that the MG24 circuit board is vulnerable to being short-circuited against anything…
G240 is a 40% mechanical keyboard designed by G2Space, featuring a custom 3D-printed body and switch plate. It includes a small OLED screen that serves as a status indicator. The primary goal of this design is to create a compact keyboard…
Ikea Skadis mount for Sonoff Dongle Plus MG24
Slide the antenna inside the case. I printed it in PETG with 0,2mm layer height.
