Liczymy pasujące modele…
--Updated V2 Available Now!-- Features 3mm alignment pins and better clearance! Use standard nails as alignment pins for more consistent driving. This is a fork seal driving tool for use with 48mm diameter dirt bike forks. This was…
Threaded oil funnel to fit most 250, 350 & 450 KTM / Husky / Gasgas motocross bikes. The funnel threads directly into your existing oil reservoir for easier oil refills. Air vent integrated into funnel to allow for fast pours with no…
If you have a 23+ KTM, Gas Gas or Husqvarna you know removing the new radiator cap is nearly impossible! Works on all 23+ KTM/GasGas/Husqvarna Austrian bikes. Print in PETG, TPU, ASA 100% infill with backing
I use the brake line guide on my 2018 KTM EXC F450 which is equipped with a navigation tower for rallye racing. It will fit on all bikes with a similar fork. The updated version is short and got an offset in order to get more clearance…
Oil drain tube for KTM Husqvarna Gasgas The thread is M12 x 1.5. Compatibility: All KTM from 2009 All Husqvarna from 2014 All GasGas from 2021 Print in TPU or PETG Instructions: Lay the bike on its side with the drain bolt facing up, the…
GasGas brand keychain, with a simple and easy design for a quick impression and low material cost.
This is a fork seal driving tool for use with 43mm diameter dirt bike forks. This was designed with WP dual chamber forks in mind, but will service numerous other fork types from KTM/Husky/GasGas. There are two lips designed into the seal…
GasGas logo keychain, with a simple and easy design for a quick impression and low material cost.
Some valve caps for vehicles, I made these with 0,2mm nozzle. This far: tesla, f150, bmw, toyota, yamaha, gasgas, will add more later.
In the case of a crash the lower triple clamp hits the steering stop screw causing marks, scratches and sometimes breaks the triple clamp. One of the detailed pictures shows some damages caused by the regular steering stop screw. I…
This is a basic tool used to adjust the Compression on a WP6500 cartridge fork. It is very handy since most bikes you would need to remove your handlebars in order to adjust with a flathead screwdriver. This is a flathead tip on a disc.…
GasGas EC 300 2002 Kennzeichen Halter weg klappbar für sumo/Enduro Abstandhülse am besten aus TPU Rücklicht: https://amzn.eu/d/bGidhtm Rest aus PLA/PETG
Hour Meter mount for KTM, Husqvarna, GasGas, Sherco Replaces the speedometer. Original made for my Sherco SE should also fit for KTM and others. I print with PETG and 100% infill for max. stability. Lasts now more than 30 hours.
I printed this tool with 50% fill and it worked great.
would print out of tpu preferably with gyroid infill to get homogenous squish the normal variant was a bit los inside the motorcycle frame so I increased the outer diameter to 20,2 instead of 20
Finding myself unable to get a new sealing from the dealership in time, I made my own sealing for the clutch actuation cylinder. Printed with TPU filament. My aim was a temporary solution to get the bike running, but it works perfectly…
Sur la photo c'est le guide oficiel gasgas avec des douilles en aluminium à l'intérieur. Sur le mien je n'en ai pas mis, donc un peu différent.
GasGas koozie whre one side is with full logo, other side with G only. i test printed with 0,6mm nozzle as I had it istalled at the moment, so works also with that.
Print the funnel like in the picture, the overhang prints perfectly without supports. I printed with a 0.4 mm nozzle at 0.25 mm layer height, but changed the thread layer height to 0.1 mm with the adaptive layer height feature in Orca…
Guide chaine origine pour VTT Gasgas pour les modèle MXC et ECC .
Cover to protect the map during washing
Petit guide à inserer sur le robnet essence d'une gasGas Txt pour reconnaitre les emplacements fremé (C) et réserve (R).
This is the gommet is you lose some for the gasgas ecc bike print in TPU
Bonjour, merci de mettre un like, si ce design vous est utile. ce filtre s'adapte sur un 300EC de 2003, avec boucle arrière de 2011, je pense qu'il doit s'adapter sur de nombreuses années. j'ai réalisé ce filtre a air, car celui d'origine…
Bonjour, merci de mettre un like si ce design vous est utile. Imprimer avec FILAFLEX 82A, remplissage à 100%. Bonne journée et bon ride.
Made for Rieju mr 300 2024 model
Standriser for KTM, Husqvarna, Gasgas EXC, TE, EC TBI Bikes with the newer angled frame on the bottom skid plate from 2024 and upward. With this riser the front wheel is lifted off the ground like on the tpi and carbed models. Print with…
Some valve caps for vehicles, I made these with 0,2mm nozzle. This far: tesla, f150, bmw, toyota, yamaha, gasgas, will add more later.
GasGas brand keychain, with a simple and easy design for a quick impression and low material cost.
GasGas logo keychain, with a simple and easy design for a quick impression and low material cost.
GasGas EC 300 2002 Kennzeichen Halter weg klappbar für sumo/Enduro Abstandhülse am besten aus TPU Rücklicht: https://amzn.eu/d/bGidhtm Rest aus PLA/PETG
