Liczymy pasujące modele…
This is a remix of the original model by fabrik872 : https://www.thingiverse.com/fabrik872 Original model site: https://www.thingiverse.com/thing:3693224 Chernobyl graphite block from inside the reactor RBMK with fragment version.…
If you've installed a R3MEN Graphite Bed then you will know it's thicker than the standard K2 bed. These tabs are attached to the rear of the K2 bed mount (see pic) . This allows you to place your build plate quickly in place without…
Original RC10B2/B3/T3 Graphite project page: https://www.rc10talk.com/viewtopic.php?t=32679 You will get good quality and strong printed parts if you order them somewhere SLS printed in PA12 material. MJF will work nicely also. All carbon…
Easy to print, nice to use. Remix from Parkside holder. Additional f3d file with parameters which enable you to adjust it for batteries of other make.
The adapter model for the Graphite screwdriver allows the connection of a Parkside battery, enabling the use of batteries from a different tool system. The design ensures a precise fit to the electrical contacts and mounting points,…
This is smaller model of reactor block from Chernobyl series Category: Scans & Replicas
R3men Graphite Bed for Qidi Plus 4 is now available for ordering at www.R3men.com The graphite bed is 8mm thick, so for more convenient build sheet alignment you can print out these alignment corner guides prior to bed replacement. Make…
So it turned out my washing machine has poor parts used as motor shaft and some users had to replace complete motor assembly to fix indesit F15 issue. It could be because of wear on motor shaft bushing that leads to rotor grinding stator…
a simple pencil to hold 2mm graphite leads with holder for snug fit!
Not a remix of this -- https://www.thingiverse.com/thing:4123073 but inspired by it. I've drawn the structure using hexagons and spacers. The spacers are designed to be quite a loose fit so the layers easily move past each other. Print…
R3men Graphite Bed for Qidi Plus 4 is now available for ordering at www.R3men.com The bed comes with a 1000w AC heater and heats up the bed in 4 minutes compared to stock bed that takes 15 minutes. AC heater of the graphite bed needs…
I printed this with: 2 wall loops 0.2 layer height 15 gyroid infill work well for me
R3men Graphite Bed for Qidi Q2 is now available for ordering at www.R3men.com The graphite bed is thicker, so for more convenient build sheet alignment you can print out these alignment corner guides prior to bed replacement. You will…
Layer height : 0.2 Supports not needed - Infill 15% gyroid - 3 walls
Graphite battery holder All of these 3d models and print profile was tested and checked, works and fitted very well, tested and remodeled couple of time to be perfect flat with 3mm hole flat with 6mm cone hole angular 3mm hole angular 6mm…
Spacer that aligns print plate if you are using R3men graphite bed. R3men graphite bed has no print plate alignment rails of backstop. This spacer makes it easy to align and have a backstop for the print plate.
A simple Clamp for the Handrail to mount the Wintercover.
Build a Potentiometer from Pencil Graphite and Paper An educational DIY project demonstrating how pencil graphite can function as a resistive element in a working potentiometer. The device combines a 3D printed body with a graphite track…
Designed a front suspension hanger for my Arrma Graphite Voltage. I needed this for the custom bumper I created ( https://www.thingiverse.com/thing:5293607 ). Thought the hanger might be helpful to someone if their part breaks for if they…
This is 2 different designs: One for 2 ballpoint refils, the other for a ballpoint refill and a mechanical pencil lead. The file named V3 is a dual ended pen, it should fit Schneider Take 4 refills, 90 mm long 3 mm diameter. The pen body…
This is the layer of graphite, printed with PLA-filament. Atoms were colored with silver acrylic paint to make model more attractive. Auto-generated supports.
Very simple parametric demo box for showing magnetic levitation of a pyrolytic graphite sheet over permanent magnets. The top border prevents the sheet from falling off the magnets. The lid makes possible to close it as a box (but there…
I need it because I keep cutting the top off incorrectly, or the flimsy plastic cap gets torn off at some point. Only requires 0.4g of PLA filament – a useful model to print from leftover filament. OpenSCAD source file:…
Tired of trying to shake that pencil sharpener to get that broken graphite lead out? This little tool is designed to help take out that little piece of lead. Print at 0.08 or 0.12mm layer height, and orient it so that the flat edge is on…
AMAZEMET upper housing graphite o-ring lock & holder removal tool. The original instructions are to set the upper housing on the ground and use a mallet to knock the graphite o-ring lock and holder out of the assembly. This allows you to…
This layer of graphite or graphene is the simplest crystal structure for school and university classes. I have assembled it with wooden dowls, because they are cheap and can be easily bought at any market place. The .stl with 2holes is…
Graphite Holder for easy access. Printed in black PETG Picture shows direct part was printed Strength 3 wall loops Sparse density infill 20% No support
I have a lot of graphite, and I decided to design a holder so it wasn't just scattered all over the place. I'm still working on it: currently, there's a V1 that has more or less random (base) sizing and a V2 with standardized base sizing,…
Graphite is stacked honeycomb carbon sheets. This model shows two AB-stacked layers with no sticks between them, because the layers are held by weak van der Waals forces. A labeled ball-and-stick 3D model for classrooms, teachers and…
5 labeled models of carbon's famous allotropes - from the diamond unit cell to a full C60 buckminsterfullerene and a carbon nanotube segment. Every atom is a sphere in standard CPK colors with its element symbol plus proton and neutron…
2B or not 2B? easy, not 2B, 4B is way better. A holder for holders of graphite. Not for graphite over 0.5mm diameter, or for hardness grades harder than 2B. Category: Office
R3men Graphite Bed for Qidi Plus 4 is now available for ordering at www.R3men.com The bed comes with a 1000w AC heater and heats up the bed in 4 minutes compared to stock bed that takes 15 minutes. AC heater of the graphite bed needs…
I have a lot of graphite, and I decided to design a holder so it wasn't just scattered all over the place. I'm still working on it: currently, there's a V1 that has more or less random (base) sizing and a V2 with standardized base sizing,…
R3men Graphite Bed for Qidi Q2 is now available for ordering at www.R3men.com The graphite bed is thicker, so for more convenient build sheet alignment you can print out these alignment corner guides prior to bed replacement. You will…
If you like this model, don’t forget to check out my other creations in my collection — you might find something else you’ll love 😉 https://www.printables.com/@Paja/collections/3228932 Thank you so much for every download, like, and…
I need it because I keep cutting the top off incorrectly, or the flimsy plastic cap gets torn off at some point. Only requires 0.4g of PLA filament – a useful model to print from leftover filament. OpenSCAD source file:…
