Liczymy pasujące modele…
This my version of the Calm Buddi turtle, manufactured by Defy Designs - https://www.defydesign.org/calmbudditurtles. My version has two shell options: 1 - ridges inside and a standard turtle shell pattern outside 2 - My Humps Edition has…
Function This blastgate could be attached to tubes with 50mm inner diameter. The other side has a conical port where a hose can be just pushed in with the 48mm adapter. The layerlines give a good hold. This adapter could be glued to the…
Remix du model https://www.printables.com/model/801477-plug-adapter Rajout du trou pour la terre pour les prises françaises ( type E). ---------------------- Remix of https://www.printables.com/model/801477-plug-adapter Just add a…
One day my Pinecil just decided to break apart. I wanted to still use the original cylinder that holds the iron tip and grounding. No sanding, wires, additional nut and screw required. Press to fit. I used supports while printing with…
After seeing online that most people plug into a banana clip adapter (which I don't love) or they just plug directly into the wall (better but only a bit) to control static, I decided to build a simple terminal post grounding plug ESD…
Used components: Banana plug connector
This mounts between the grounding block and the desk to allow you to hang an ESD strap. My biggest gripe with these B9742s is that there's no built-in provision for this, like you would find in a bent steel grounding block such as the…
I decided to take my UNU Scooter apart and found that the holding brackets for the grounding strip inside had broken. So i made a quick design from the dimensions of the old bracket and made it 3D print friendly. It can be printed without…
Flat electrical contact, EU plug type E
Update Nov 14 2025 I added the model with the clips already attached for printing with supports. I printed using PETG and used standard hot melt glue to glue the clips onto the frames. The leveler can be used to hold the clips level while…
This is a box that will take 4x Banana Jacks, to be wired together with thick gauge tinned bus wire, and then ran out the box via a (also adequately thick gauge) cable which can be attached to a ground point, either via a wall outlet or…
When there's little humidity in the air, I seem to build up a lot of static electricity in my carpeted office. When I touch any computer peripheral, my monitor flickers, my speakers pop, etc. I found a old cabinet knob and designed a base…
My original grounding post worked so well that I had to stylize it a bit. Here's a version patterned off a Tesla Coil. Original Grounding Post description: When there's little humidity in the air, I seem to build up a lot of static…
If your guitar hums like a beehive till you touch the strings or your audio interface, congratulations: you’ve discovered the wonderful world of ungrounded switching power supplies. Since your laptop or multi-FX pedal likely uses a…
This is a little grounding bracket which allows you to connect up to two ESD wrist straps to earth. Two 4mm banana jacks are like these re required: https://s.click.aliexpress.com/e/_c4B49lB3 or on amazon https://amzn.to/4v4FAYn (these…
A simple and compact mounting plate designed to hold five 4 mm female banana sockets for ESD grounding and electronics workbench applications. The model features 5 × 8 mm mounting holes with a slight tolerance to compensate for typical 3D…
This my version of the Calm Buddi turtle, manufactured by Defy Designs - https://www.defydesign.org/calmbudditurtles. My version has two shell options: 1 - ridges inside and a standard turtle shell pattern outside 2 - My Humps Edition has…
If your guitar hums like a beehive till you touch the strings or your audio interface, congratulations: you’ve discovered the wonderful world of ungrounded switching power supplies. Since your laptop or multi-FX pedal likely uses a…
When there's little humidity in the air, I seem to build up a lot of static electricity in my carpeted office. When I touch any computer peripheral, my monitor flickers, my speakers pop, etc. I found a old cabinet knob and designed a base…
