Liczymy pasujące modele…
I wanted to charge my iPhone, Apple Watch and AirPods all together beside my bed. This model is designed to use: 2 x Apple MagSafe Chargers 1 x Apple Watch Magnetic Fast Charger You can get them either directly from the apple store, or…
Simple Slip together stand for Icharger and Power lab 6 type of Chargers. Straddles Power supply. This will hold charger at a steeper angle to view screen easier. I have used the design in PLA with 20% infill in AZ no problems. Take away…
This is my version to rise AA & AAA batteries so they can charge properly. There is a grip area to remove the riser easily. The "bottom" part of the riser is flat to enable a good access to the batteries. It is also possible to leave the…
The design of the Autel Multicharger for the Nano Drone is very minimal, lets say. This case adds only a minimum of more space required in your bag but gives a much saver/better feeling when plugging in the batteries. Print time was…
Simple Icharger X6 Base velcro to power supply printed in pla 203/50 Print instructions Unassociated tags: charger base, icharger x6 Category: R/C Vehicles Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: .2 Infill: 15
print left side down, no supports requiered
Basic Icharger stand straddles power supply let charger sit around 45 degree angle. Has two different size braces. If using PLA suggest using 75% or more infill to keep parts from warping from heat. PETG i use 25% infill no warping. I use…
Wall mount for Nitecore digicharger D2. Cut-outs for buttons and ports. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0,2 Infill: 100 Filament: 3DE Premium PLA Black Notes: The file has some…
Inspired by, but not a remix of, or as nicely designed as https://www.printables.com/model/177142-nitecore-d4-digicharger-aaa-aa-akku-battery-riser
Single battery riser for AA and AAA batteries In the Nitecore Digicharger D2.
Zum zusammenfassen von mehreren Ladern gedacht, müssen dann nur noch zusammen geklebt werden.
Fill the bottom compartment with whatever you'd like. I used a few 8g weights and a bunch of rice. Use some M3 screws to secure the covers and you're good to go. You can always add some rubber stick on feet too!
Riese Muller Multicharger Eurobox mounting Brackets for a clean look and distributed weight. Standard Front carrier (not the cargo one). Cable Ties 4-5mm wide. Use a durable material such as ASA. Layer height 0.12 or lower for higher…
An adapter for NITECORE Intellicharger i4 to fits AAA batteries comfortably and stable during charging. Made in Autodesk Fusion 360.
I created this model to anchor the luggage tensioners on the safety bars of my Riese & Müller - Multicharger 2. Safety bars - 4 corners This is the file with all 4 corners. Normally you should use this file if it fits your print area.…
Riese and Müller Multicharger Back holder - Made with 3D printed parts and 20 mm electrical PVC pipe. Printed in PLA
The NiteCore D4 digicharger can't recharge NCells properly because the minimum contact position is like 0.5mm too short, and the batteries drop down too low and fall below the bumps and it is a very dodgy connection that needs some…
I made a cover for my Nitecore i2 Battery charger as I didn’t like the fact that the batteries were exposed and could easily be knocked out of place. The cover snaps in place and can easily be removed. I also made sure it was not fully…
Nitecore Intellicharger i4 Pegboard Mounted Holder remixed from Ahmad AlAmrey's model together with the Multiboard Pegboard Click Hook. Print with supports
Print two - one for top and one for bottom. If you just want to attach it directly to a wall, use these attachment points . The hole spacing is at 25mm intervals. You will minimally need two of those mounted 100mm apart vertically. For…
Nitecore Intellicharger i4 Pegboard Mounted Holder remixed from Ahmad AlAmrey's model together with the Multiboard Pegboard Click Hook. Print with supports
Should be best printed vertically or diagonal. Printing it on its back will make the clips that hold the charger weak and might break when installing,
A simple wallmount for a charger. Comes in two versions: one for screws and one for doublesided tape.
This holds my Intellicharger i2 charger along with it's power cord. I don't use magnets so there are no magnet holes in this model.
Designed this toothbush multicharger stand to simplify our bathroom and use less outlets. Also prevents brushes from getting knocked over. Base uses wago connectors to make connection. Also possible to solder and heatshrink connections.…
