Liczymy pasujące modele…
Stable and waterproof OpenSCAD case V7.4 by pbtec See here a wonderful comment from a user: “This is INSANE! You sir deserve deserve the biggest applaud out there. This is a box to rule them all! … I have to admit I first didn't…
Waterproof ip67 ip65 Junction Electrical Panel Box by dury
Extension for Mitutoyo caliper gauge (Tiefenmesser) made for MITUTOYO Digital Absolute 150 mm IP67 Input / idea came from @jackenhack but this 3D model does not fit to mine Mitutoyo caliper gauge, so I need to redesign the full model new.…
It's a small clip for mounting the LED Strip to a Wall or Ceiling. I designed it for the WS2815 IP67 LEDs. It's nothing special, nor did it need any big Work for designing it. It works and gets its Job done. I would recommend to print it…
This is a direct replacement for the original mounting plate included with the TICONN Waterproof Electrical Junction Box (8.7" x 6.7" x 4.3"). Modeled in Fusion 360 using the dimensions of the factory plate, it replicates the two standard…
Note: The Ethernet Module PINs didnt land where I expected based on the model, so I used a knife to cut the lower two standoffs. I attempted to replicate this in the .STEP but its not tested and certainly would be below the expected…
IP67 LED strip clamp with FreeCAD ( RT ) file. For dimensions check the picture.
I made a holder for my LED strips from BFT Lightning. In my case, it fits the 24V WS2814 RGBW LED strips with 60 LEDs/m and IP67. The LED tube sits fairly loosely in the holder, but it works well enough for my needs. The bar that holds…
This is a mount adapter for an IP67 junction box to attach to a pole, mast, or anything round-ish using hose clamps or stove pipe straps. Remixed from this excellent model by @quantenquark . The use case would most commonly be for a…
This is a clip to hold WS2812 LEDs at a 30 degree angle from a ceiling or wall. The inside of the clip is designed to hold a weatherproofed strip with a silicone sheath measuring about 12.3 x 3.85mm, so any LED strip using such a sheath…
Version 1: A mounting plate for a Nebra IP67 enclosure to install a Meshtastic node based on the RAK19007 WisBlock board. Includes a mounting spot for a diymore 18650 battery holder. Version 2: A mounting plate for a Nebra IP67 enclosure…
English This holder is a minimalistic approach to mount the Mitutoyo IP67 Caliper to the wall. In my case I mounted it inside a steel cabinet by using double sided tape (works so far). If you want, there are 2 screw holes in it, if you…
Needed some magentic mounts for led strips to go under a camper. Two size magnets can be used 8x2mm and 10x1.6mm. Magnets are kind of a tight fit but should press in without having go glue. If not, just use a little dab of CA/super glue.
A magnetic mount for the Anytitit water proof power supply (https://a.co/d/csDCMdf) The holes for the magnets may need to be cleaned up a little to get them to fit. Use 20x3mm magnets.
This is a simple screw mount for IP67 LED strips . I designed it specifically for my SK6812 IP67 60 LEDs/m RGBW strip to mount the strip securely to my garden cottage. The screw holes are sized for 4×30 mm screws , but smaller screws…
Grid for components in hermetic housing ZP120.80.60SUJ-IP67 TM ABSGrid for components in hermetic housing ZP120.80.60SUJ-IP67 TM ABS
The 18 liter sealed container from 5Five is IP67 rated, stackable and can store five 1 kg spools at once for drykeeping. I designed a silica gel bin and spool supports that fit the bottom profile of the box. Optionally a hygrometer holder…
Clips for mounting ws2815 12v 144led/m ip67 led strip under vehicles or rough environments surface mount clip one sided floating clip end cap clip (Designed to fill with silicone/rtv or any appropriate adhesive)
I purchased this https://tinyurl.com/by3y4cyt to power some led strips above my trash zone. I was unhappy with the flickering of “refurbished” adapters I used. This was the solution. Thing is below a roof but being IP67 is really…
Basically what it says on the tin - using Ezy Storage 11.4L IP67 Waterproof Storage Box to reduce moisture ingress for hygroscopic filaments. Assembly 1. Drill the 4mm hole for PTFE tube. Use wood drill bit, go easy on the pressure to…
Simple replacement key for your miutoyo caliper for when you need to change the battery.
This is a mount adapter for an IP67 junction box to attach to a pole, mast, or anything round-ish using hose clamps or stove pipe straps. Remixed from this excellent model by @quantenquark . The use case would most commonly be for a…
