Liczymy pasujące modele…
I modeled this awhile back to replace the factory tool box on my 1st gen Kawasaki KLR 650. It's best to print it in ABS so that it can withstand sitting in direct sunlight in the middle of the summer. I don't remember the settings I used,…
I got sick of funnels that didn't fit in to my bike. So i made one. https://www.youtube.com/shorts/qi6h9ViouRc This is a print in place funnel with a screw in design, Its designed on an angle to get around the exhaust on my KLR 650. The…
Shortens the Blinkers on the bike. Reduces chance of them braking if the bike is dropped on its side.
This small 3D print is made for the HK Army KLR masks to mount a GoPro to, using 2 M2 screws and nuts and 1 M5 screw and nut to secure the camera to the mount. No support needed and takes about 21mins to print using 0.20mm and it will use…
Printed the original version in PLA with 100% infill and I had no issues on multiple road trips. Printed a new one with PETG at 100% infill just to be safe. Print with supports. They're needed for the upper lip. I tried to make it angled…
only changed the letters to be inset on the lid to be printed without using supports
Use with an M3 insert and socket cap screw with locktite. Turn signal wires stay intact, there's no need to cut them. It's recommended to print in a UV resistant ABS, ASA, or PETG for durability.
KLR 650 Front fairing spacer washer for when you loose them or if you buy one that doesn't have them
Haken für Kunststoff Steckregale (zb. OBI) / Hooks for plastic plug-in shelves (e.g. OBI) Diameter: 33mm in verschiedenen Ausführungen
I made it smaller to fit the handlebar on my 2023 KLR 650. I created a phone holder since I do not want to use two-sided tape on my phone. I merged the bracket to the phone holder. Here is the Tinkercad.com link to my public model. If you…
Simple seal driver and backing support for installing a water pump mechanical seal into your KLR650 engine cover. Designed to be used with a 5/16ths bolt. Be sure to use washers on the prints to spread out the load and use a high infill…
This will fit all 4x7" US License Plates, typically used for motorcycles. Apparently there is no mounting hole standard for motorcycles like there is with four+ wheeled vehicles, so I left them for you to drill yourself to match your…
it's a replica of the kawasaki klr 650 turn signal shell, with support in the printing process and 40% fill, pla+. I suggest to adapt the gcode to your printer. My print has a lot of small bridges(maybe the no-load movement speed it's a…
Uses an M5 nut on the back. Print in TPU. These should probably only be used temporarily. Category: Automotive
I designed this to replace the bulky rubber knob on the shift lever of a gen3 KLR650. When running boots I had a hard time shifting, this resolved the issue along with a relief cut on the shifter allowing it to drop one more spline. Print…
I couldn't stand the low windscreen on my '12 KLR and was considering buying the riser kit that everyone puts on their bikes. Decided to check for 3D printable solutions and found the one posted on Thingiverse. Printed that, but the…
The infamous "doohickey" modeled for fun. Doos: Make a keychain, Show your friends what you mean by "did the doo", remix into doo benchy. Doo'nts: Use as a replacement for your KLR, Ingest, or insert rectally. Enjoy
Printable replacements for those annoying plastic washers that go missing on the gen3 KLR650's fairing and windshield screws. Replaces Kawasaki PN: 92200a and 92200
Lost or misplaced the grommet collar for your KLR650? This is part replaces Kawasaki part # 92027-1183. This collar is pressed into the rubber grommets in the lower fairings where it bolts to the fuel tank. Installing the fairing without…
Print instructions material: PET-G is strong enough, ABS would be better, NYLON is the best infill: 100% for PET-G suports: yes layer: max 0.2 mm Print all parts in horizontally, all layers must be in 90° to the longitudinal axis to avoid…
Use this part to replace the fragile plastic battery holder on your early model Kawasaki KLR 650 Print in PETG, ASA or better. Route the trickle charger cable down from the battery Use a cable tie to attach the cable to the part I accept…
A quick and simple spacer for the gen 3 KLR650s seat. The screws and subsequently spacers rattled off mine and after replacing them a few times I said screw it. These fit perfectly and were designed to be used with m6x30 thumb screws but…
Print instructions material: PET-G is strong enough, ABS would be better, NYLON is the best infill: 100% for PET-G suports: yes layer: max 0.2 mm Print all parts in horizontally, all layers must be in 90° to the longitudinal axis to avoid…
This spacer lowers the front fender on the KLR650 to better clear the radiator and frame. Some aftermarket front fenders have a shallower angle than OEM past the head tube which can cause them to rub. This spacer lowers the front fender…
No funny settings is needed. Just print it slow to make sure you get the detail. Category: 3D Printing
I lost (i think my dog stole) the damper to the tank on my klr650. Modeled this up and hot glued it in. Printed from PETG it works, but TPU would be better. 35% Infill
A small and simple container that carries two glass cartridge fuses. I made it so that I can carry two spare fuses for my KLR650 in my onboard toolbox. Because the glass bodies of the fuses are fragile, I decided to sink them completely…
