Liczymy pasujące modele…
Not much to say - I used it to power an arduino nano sound and light installation where I constructed a frame where the battery holder can be clipped in. So it is easy and save to print. I used this…
This is my design of dish that is ventilated from below. Objects placed in this dish dry fast, as there is an air flow possible from all sides. How to Print the Dish Print the dish with the flat bottom on the print bed. In order to get…
As a dedicated craftsperson, organizing those myriad of tool bits—each crucial for different tasks—can be quite the hassle, especially the ones used so seldomly they seem almost forgettable. To streamline your workspace and ensure every…
Handle replacement. The M6 thread for the cables has to be cut by hand. For the 3 front screws, I heated the heads of the original self-tapping screws and turned them in to "melt" a proper thread form. So the holes are a bit closer, 2mm.…
Gridfinity battery bins for D-/R20-batteries. The bins can be stacked by using the included spacers. A 1x2x4 bin that fits 2 batteries. A 2x2x4 bin that fits 4 batteries. A 1x2x6 spacer that is needed to stack the 2-battery bins. A 2x2x6…
New Version 1.1 Note: In September, 2023, a fellow V1E maker ( @steved on the V1E forum ) needed a little bit of adjustability on the location of the right-side belt-tensioner+endstop mounts, and so I made a v1.1 remix of this design ,…
Hi, I have built a small “battery thief circuit” some time ago to drive a LED-String-Light with a few old, almost empty batteries. Normally I use AA and AAA type batteries. But I grabbed a few “D | LR20 | Mono” and "C-Baby | LR14" cells…
I've run out of LR20 while having plenty AA's so I designed and printed this adapter. Due to lack of space for classic “spring” connections I used copper wire as battery connector. Parts needed: 30cm of stranded copper wire (0,5 to 1 mm2)…
It use a buck converter to regulate the voltage from 11.4v to 7.5v. You can use washers as connectors at the battery ends. I recommend that you use some switch or connector that you can disconnect to power off the buck converter or it…
Simple tool to lift a row of LR22 cartridges and place them in another box or simply grab 5. The green print in the picture is printed on a Babbulab X1c with eSun PLA+ Peak Green
…takže jsem vyrobil adaptér pro Li-ion akumulátor velikosti 18650, jehož napětí je pro funkci otevírače dostačující. S výhodou jsem použil článek Fenix s integrovaným ochranným a nabíjecím obvodem a s konektorem micro usb. Adaptér…
Designed specifically for artists, these inserts for the LR2052 Storage Box System provide a perfect solution for organizing small paint tubes. Each insert is crafted to snugly fit and protect various brands of paint tubes, ensuring they…
This is my simple design of a short drain that can be printed with PETG and without any supports. The idea is to glue or screw this drain on the bottom of a container, pot or pipe to direct the water flow into the desired direction. How…
I created these simple adapters because I needed LR44 batteries for thermometers and at home I only had LR927 batteries available, so I recreated the shape of the former by interlocking the latter. Very simple but functional (both are…
Introduction This project provides customizable insert blanks specifically designed for the LR2052 Storage Box System . These inserts are purposefully kept simple, incorporating essential design features to ensure a seamless fit across a…
Handle for LR20 for WECP20 soldering station - Weller. The handle has been optimized to provide a better finger stop and an improved grip The M6 tapping intended for the set screw used to secure the power cable must be drilled to Ø5 and…
I have a flashlight that I bought cheap where the AA bettery does not fit well and I used to tape it to make it wider and not rattle in the flashlight. When looking closer at the description I found out that the flashlight was made for A…
Spacers for a common modification to a Losi/TLR TLR22/22T Instructions This is a spacer set for a TLR 22 22T to raise the transmission case by 1mm, as decribed in the Losi racing blog entry…
USB powered LR20/D battery. mini DC-DC step down converter (11x17mm or smaller)…
This will fit all 4x7" US License Plates, typically used for motorcycles. Apparently there is no mounting hole standard for motorcycles like there is with four+ wheeled vehicles, so I left them for you to drill yourself to match your…
Sony RMT-DSLR2 remote accept CR2025 batteries, as I dont have such one at home I modeled new tray which accept CR2032 battery. Printed on Bambulab X1 Carbon in PLA with 0.08mm profile
A 1x1x3 Gridfinity bin that can hold a JJC RM DSLR2 Remote Control. Built on top of kennetek's Gridfinity Rebuilt in OpenSCAD . My code for this is also open-source. See it on Github .
