Liczymy pasujące modele…
You will need M4x6x5 heat inserts. If you would like to use something else or screw straight into plastic, there is also a .step provided. M4x10 screws are a perfect match for attaching the stepper drivers but make sure the head isn't too…
Version 4 added 8/13/25 but is untested. This is a simple valve spring compressor tool I designed for the M54/52 cylinder heads. I printed this in Overture PC on a Bambu Lab X1C in draft mode (0.28mm layer height) with 4 perimeters and…
DM542 stepper motor driver dins rail mount with Solidworks 2016 file This file is to be used with this din rail clip .
Adjustment kit for the Vanos in BMW engines (M52 and M54) I found the Vanos adjustment measures on BMW forums and made this jig/kit to adjust the Vanos to these parameters. It worked a charm on my engine swapped Z3 who's vanos got out of…
The holes are printed tapped for an M4 thread. You will need to print one tab for the bracket. It can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab Category:…
Printed with PLA, 4 perimeters, 30% infill
it`s advised to print solid, i printed the adpater in PETG ony because that was what was in the printer PLA i just fine, it took 57Nm to release the fileter cap, and to tool could handle that, filter cap should be tightend to 25Nm
As a Carguy I tryed out someting new, let me know if you want to see more and send me your wishes. Print settings I used: length: 90mm hight: 2mm nozzel: 0.2mm layerhight: 0.12mm Note: A 0.4 nozzle should be no problem. Of cource you can…
-Funnel for pouring oil into the M54 engine, will also fit the M52 engines and probably the M50. - fits into the hole and holds it in place when pouring. - It will certainly fit other makes and models of cars, but unfortunately I have not…
-Funnel for pouring coolant into the M54 engine, will also fit the M52 engines and probably the M50. - fits into the hole and holds it in place when pouring. - It will certainly fit other makes and models of cars, but unfortunately I have…
A simple friction fit case for the XH-M543 amplifier Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 20-50% Material: PLA
I bought my E46 without this tube and was reluctant to pay $47.79 for it on FCP Euro. Ended up costing a lot more than $47.79 in time to model and it still isn't perfect. That said, it does fit and is much better than nothing (see…
This design is without a doubt the best type of 3d printable DIN rail mount. It is made to use M4 screws threaded directly into the hole. I had to adjust my horizontal expansion to allow this spring to slide freely. But it works so well.…
BMW e46 M54B22 Intake vacuum/smoke test adapter Made it to test for any vacuum leaks. Fits e46 m54b22 or other cars with intake diameter equal to 80mm Supposed to be used with Standard automotive valve. (Unfortunately the rubber one is…
3, 5, and 10mm extenders in M54x0.75 threads. Useful for telescope and astro camera connections.
This is a basic M54 spacer. These things usually cost more than you'd expect, so I just modeled it up myself. This model is 0.1mm thick, and can be scaled to the width you need by scaling the z axis in your slicer of choice.
Print 2 pieces for assembly Allows the use of thinner old style m50 dipstick on a M54 style sump. Printed mine in PLA and smeared RTV on the outside lip. Use original o-rings Has held up fine so far for me but your mileage may vary.
XH-M543 (TPA3116D2) case for mounting under desk. Power through XT30-M connector You can use 2 inserts m3 with 4mm length, or just melt 2 plastic pins I used a minijack 3.5 mm female this type:
Hdt3m pulley with 54 teeth for electric longboard. Pulley uses these wheel adapters: https://www.thingiverse.com/thing:2969654 Pulley dimensions: Diameter 50.5mm Width 12mm Middle hole 21.5mm Holes and screw head sink are for M5 hex…
Un mando para un microondas Whirlpool model:AVM541/WP/WH Diseñado en tinkercad: https://www.tinkercad.com/things/8ZQctEBHpBv Si necesitas ayuda para modificar puedes hacerlo en el email: [email protected] poniendo en asunto "Ayuda…
You can use this tool to swap the filter plug on your Avon mask from one side to the other, etc. Designed as a replacement/backup/cheaper alternative to Avon's $30 piece of plastic:…
This is a modification of the SCUTTLE robot v3's battery DIN mount to fit a DM542T Stepper Motor Driver. The mount is held to the din rain using part of a 1 ¼" binder clip. Remove the binder clip handle, then bend it out slightly to make…
A case to hold the block thread repair kit for head bolts on a BMW M52/M54. The kit shown comes from SpankRanch Garage . This kit built with high quality components, but noticeably more affordable than other commercial options. This case…
bushing to hold injector connectors to the plastic rail, to replace any missing or broken stock ones. Made for m54 / m52tu, might fit others that use a similar design. Printed in TPU for the flexibility, and tpu deals pretty well with heat.
supporting m3 5x5 heat insert (voron style)
Fits this: MantelMount MM540 https://www.mantelmount.com/collections/mounts/products/mm540-enhanced-mount and maybe other MantelMount things. Highly recommend this tv mount, btw. Great product. Allows you to fit a bigger speaker under the…
Something small I made for astrophotography This is pretty thin but let me know if you want me to enlarge or shrink it :) About .6mm thick.
I developed this adapter to thread onto the rear cell of my Celestron Nexstar 8SE SCT. The female part mates to the rear cell with a 2", 24TPI thread, and provides an M54x0.75mm male port, which I used to mount my ZWO ASI 2600MC Duo. The…
I found out the hardway there are about 2-3 different versions of the SV226 Filter Drawer. This is for the newer ~2026 version that is designed specifically for M54. The thinner one is the one I remixed. Magnet hole is about 6mm x 1.7mm
M54x0.75 threaded dust caps, male and female, for astronomy. These threaded dust caps are useful for astronomy cameras, telescopes and adapters. This thread size is often used for full-frame cameras and many refractors. I print these dust…
