Liczymy pasujące modele…
The Microjig Matchfit system is endlessly useful for custom jigs, storage, organization, etc, but the bits and knobs are on the expensive side. I modeled and tested a number of variations to land on these, which are fully compatible with…
This is a series of clamp pads for the Microjig MATCHFIT dovetail clamps. The green rendered pads are for the swivel end of the clamp. The blue rendered pads are designed for the dovetail end of the clamp. Simply invert the clamp and use…
I modeled the MatchFit Setup Gauge because, for every blade, you have to have another one. A total of two 6mm x 3 mm magnets are needed allowing this to magnetize to table saw top. These should press fit depending on the accuracy of your…
I have a bunch of Jig making nuts, bolts, knobs that use ¼-20 size, and I wanted to use them with the Matchfit system. Remixed to allow use of the bolt heads and another for flat heads/T-bolts. UPDATE 02/24/25 - Reuploaded the STLs to fix…
Remixed "Parametric customizable hand knob" (credit: cschwarz) to fit Hex Nut hardware specified by "Dovetail Track Nuts (MatchFit Style)" (credit: JAREDSMOOT) and further altered the knob to closely match original MatchFit hardware.…
Once you have an initial relief groove cut you can use the relief guide with the Makita router plunge base to add more grooves at 4" intervals. (Swap out the original sub-base for the 3D print). Change to the dovetail bit, check the bit…
Die Nutsteine wurden in einer Auflösung von 0,16 mit PLA+ und 16% Infill gedruckt.
This has screw holes to attach to a wall, or in my case, I attached it to a small block of wood with a 45 deg cut to hang on my French cleat wall. for the larger clamps, you'll need to leave a slot open between them because they are…
This is fully compatible track nuts and bolts for Micro Jig Matchfit system. It uses both hex bolts and heated inserts for flexibility. Fully compatible with original hardware - uses same thread #10-32 Threaded rod (cut your own size) -…
The model is made with the exact specifications of microjig's dovetail profile for their entire matchfit system.
These are a bit ugly, but they worked for my purpose just fine so I'm uploading them in case they help someone out. You can flip them over for thin or thick material. There are two components. If you make the triangular pieces shorter or…
A remix of interactive3s design for my Dewalt 8mm palm router (DCW600) and plunge base(D262004).
To be consistent with the MatchFit M5 threads and to secure this featherboard - https://www.printables.com/model/288569-featherboards - I made a one piece miter bar that accepts M5 hex head screws. It's not as tall as a normal miter bar…
80mm long interior clamping surface. Two of these can be used in unison (exterior/interior) with a single Matchfit clamp on the diagonal. The bracket has interior and exterior matchfit clamp openings along the sides. easily compatible…
The Microfit Microjig for getting great Dado's. You will need 2 - 3 or 4 mm bolts depending on what you have there are both in the model. You will also need two inserts for the top nuts. The other half to this model is at…
These corner radius guides locate on 90 degree corners and have clamping grooves sized for Microjig Matchfit clamps. When clamped down you can route corners without hitting your clamps. Sizes are marked on the bottom. Print with 2 colors…
Microjig matchfit clamp v-block
This is a plate that attaches to the Bosch 1617 Router or the Dewalt DCW600 Router. It has a guide for Matchfit grooves, so after you create your first relief cut, the cutout in the router will fit in the groove to guide the rest of the…
Remodelled from https://www.thingiverse.com/thing:3728184 I found the original version a bit stabby and didn't work well with M6 hardware. Category: Tools
Spacer for setting the depth of the Matchfit dovetail bit. One side is set slightly shallow for using a 1/4" straight bit to remove the bulk of the waste. Then switch over to the Matchfit dovetail bit at full depth for a nice clean…
I've seen various clamping squares available for print, but not as many with the MATCHFIT system. This is a simple take on the right angle clamping bar from Microjig's YouTube channel. If you have suggestions or ideas, please let me know.…
When I set up my router-bench with the Micro Jig MatchFit System, I need stops to allow me to position multiple pieces for the same routing process. Since Micro Jig does not sell the kind of stops I need, I designed my own for printing.…
