Liczymy pasujące modele…
FAQ I have built a X500 size quad-copter and I needed to reduce the vibrations to the MATEKSYS H743-SLIM Flight Controller as much as possible. This module will only fit the MATEKSYS H743-SLIM v2 and v3 flight controllers. To complete…
This is a sizing blank
This case protects your mateksys ELRS-R24-P6 receiver, and makes it easier to mount to your RC plane or car. There are two versions, one for straight pins that come with the receiver (I didn't test fit this because I use angled pins.)…
Did not find an GPS holder which fits my needs so i designed a new one. I used TPU printing this, and double-sided tape on the bottom of the GPS module. Fixed with an ziptie, which also fixes the wires underneath. Its a MATEKSYS GPS &…
Purpose This mount allows the Mateksys M10Q-5883 GPS & Compass module to be fastened to the Speedybee Master 5 v2 RC drone. It mounts the module to the drone's rear. Special care was taken to design the mount such that the module sits…
A case for your mateksys elrs-r24-v receiver. Designed to fit this receiver but also fits crsf-pwm-v I redesigned the entire model, taking inspiration from this model , and made it fit a bit better. It also snaps closed.
Purpose This mount allows the Mateksys M10Q-5883 GPS & Compass module to be fastened to the Speedybee Master 5 v2 RC drone. Instead of mounting the module to the drone's rear, the mount moves it to the front. The main purpose is to get…
I printed it with 0.16 mm Layer height. You may need to add a brim to prevent the pieces from falling over. Tolerances are pretty tight, but that should be no issue for any well-tuned printer.
For Martian II frames, which have MatekSys H-LED with buzzer installed at the back. It ventilates, holds firmly in position, no possible shorts to GND. Print instructions Category: R/C Vehicles Print Settings Printer Brand: Prusa Printer:…
I printed it with 0.16 mm Layer height. No supports needed. You may need to add a brim to prevent the pieces from falling over.
I printed it with 0.16 mm Layer height. You may need to add a brim to prevent the pieces from falling over. Tolerances are pretty tight, but that should be no issue for any well-tuned printer.
Mounting case for matek optical flow and lidar sensor with 30x3mm bolt pattern. Fits GEPRC GEP-LC75-V3 or any 30mm mount. These things are made to pretty shoddy tolerances so I provided the files if you need to nudge the loft for the…
This print is a friction slide mount for the Mateksys M8Q-5883 . It can be hot glued to any desired surface. The design is parametric and can easily be modified.
Mount for Mateksys loud buzzer , just behind the camera. print with any material. Any feedback is appreciated!
Mount board for Mateksys F405 Wing V2 and ESC 4in1 including GPS, elrs and antenna mounts.
I printed it with 0.16 mm Layer height. No supports needed. You may need to add a brim to prevent the pieces from falling over.
Purpose This mount allows the Mateksys M10Q-5883 GPS & Compass module to be fastened to the Speedybee Master 5 v2 RC drone. Instead of mounting the module to the drone's rear, the mount moves it to the front. The main purpose is to get…
Purpose This mount allows the Mateksys M10Q-5883 GPS & Compass module to be fastened to the Speedybee Master 5 v2 RC drone. It mounts the module to the drone's rear. Special care was taken to design the mount such that the module sits…
This print is a friction slide mount for the Mateksys M8Q-5883 . It can be hot glued to any desired surface. The design is parametric and can easily be modified.
Adopted this to fit with the Mateksys F765 Flight Controller. Print Settings Printer: Sidewinder X1 Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: Anycubic PLA black Category: R/C Vehicles
This print is a solid self-snapping mount for the Mateksys H743 Wing V2 . It can be hot glued into foam planes, or it can be screwed into wood planes with a US #4 wood screw or similar. The top lid securely snaps into the base, but can be…
