27 modeli
Design highlights Uses minimal filament to print Prints fast (about 2 hours) Defaults to the optimal 12° Angle is fully adjustable with the feet Built-in bubble level Attached to the stand using the front tripod mount and the rear "thread…
I have all of my kids sports games on video from this summer except for the ones in a light rain. So here's a case that will protect your Mevo Start from the rain and gives a handy cold shoe to mount microphones, etc. Print in PETG for…
Design highlights Uses minimal filament to print Prints fast (about 2 hours) Defaults to the optimal 12° Angle is fully adjustable with the feet Attached to the stand using the front tripod mount Separate floor alignment guide Version 2…
The circular polarizer that I prefer can be found here… https://a.co/d/bLswZdH
This model uses two fans that can be found here… https://a.co/d/98n9saO
I recently nerded out at my kids baseball games and started streaming games via my GoPro. After a number of issues (like so many others) with the GoPro, I tried the Logitech Mevo, and had great success. Problem was, I couldn't find a…
Leveling stand for the Flightscope Mevo+ launch monitor. Makes leveling easier especially on the driving range grass. Multiple slots for adjusting angle (good for outdoor vs. indoor). Also a slot for a small bubble level, but I found it's…
Here’s a simple leveling stand for a MEVO Gen2 golf launch monitor. There is a slight amount of X-Y wiggle room in the tray area so it’s easy to make very fine left-right adjustments without having to re-level the unit. I didn’t add a…
A cover to protect the front (including the lens) of the Mevo Start camera. It's a snug fit so it doesn't fall off. I'm not sure if that will cause scratching in the future (it hasn't done anything so far but I've only used it for about a…
I liked the design of the original case by mressler, but it was too long for me, and I use the upgraded base by LynkSpyder so I adapted this to suit my need. Thank you Mressler for including the fusion 360 files with his model. I printed…
I have all of my kids sports games on video from this summer except for the ones in a light rain. So here's a case that will protect your Mevo Start from the rain and gives a handy cold shoe to mount microphones, etc. Print in PETG for…
Printed in white PETG and did well for an entire baseball season. Please pardon the picture. It got stepped on at one point and broke and was reattached with hot staples. Still going strong though!
Allows the stand to be printed on a smaller bed.
This a replacement base for the Mevo Start. It uses the threaded metal insert from the original base. Printed with PETG with a layer height of .12 due to the threads. Metal insert will be tight towards the end of insertion. You will need…
As a new FlightScope MEVO Gen2 owner I wanted to speed up my setup. This is a clip-on bubble level that will quickly get you very close to the recommended 12* tilt and 0* roll. Use is simple. Just drop it on top of the MEVO Gen2 and level…
The Cold Case is a great model. These modifications are useful for hot days or in more wet/humid environments. I modified the Cold Case to reduce the amount of print material that makes contact with the camera. I saw a lot of "paid"…
My brother wanted a powered mover for his Mevo+ golf simulator sensor so it can quickly switch back and forth from positions for a Lefty to a Rightly in his simulator room. So I made this up. I used it as an excuse to practice my…
Mevo Start "cold case" . The bottom has been modified to use a 3d printed replacement base.
As a new FlightScope MEVO Gen2 owner I wanted to speed up my setup. This is a simple reel to store an 8’ long nylon cord used to quickly measure the exact required 8’ distance from the MEVO Gen2 to the tee. I keep a couple of tees with…
Added cold shoe mount rails to either side for more flexible mounting of microphones and other gear
Mevo (Plus) Camera Replacement Shell / Ersatzgehäuse Rette deine Mevo-Kamera vor dem „Sticky-Surface-Syndrom“! Da die originale Soft-Touch-Gummierung meiner Mevo Kameras mit der Zeit unangenehm klebrig wurde, habe ich dieses Ersatzgehäuse…
A support to mount a cheap IKEA STÄNKREGN ring light on a Logitech MEVO. Print with TPU. Picture figure a V1 printed on FLSUN QQs (about 1+ hour print time)
While Restoring my 2003 Ford F150 Lightning, I installed new Front Mevotech TTX Upper control arms. When reinstalling the abs sensor cable, the clip that holds the cable to the control arm didn't fit anymore because of the TTX square…
All credit to original auth. I just took the .stl and modified so I could attach the boomstick I bought from amazon.
Leveling stand for the Flightscope Mevo+ launch monitor. Makes leveling easier especially on the driving range grass. Multiple slots for adjusting angle (good for outdoor vs. indoor). Also a slot for a small bubble level, but I found it's…
The Cold Case is a great model. These modifications are useful for hot days or in more wet/humid environments. I modified the Cold Case to reduce the amount of print material that makes contact with the camera. I saw a lot of "paid"…
