Liczymy pasujące modele…
A 13mm distributor with 2 4.6 mm pipe connections Two O-Rings (10.6mm x 2.7mm ) for the 13mm connections are needed
Wydruk około 0,80 €–0,97 € nettoWstępna wycena dla PETGMateriał u źródła: PET
My microdrippers keep popping out of the 4.6 mm tube even though it's a new original tube and I'm using an original A2000 pressure reducer. The new recipie for a softer 4.6 mm tube worsened the problems. This solution involves placing a…
Remixed from Dunderklumpen's model
Secures a 13mm tube. The tube will not slip out. I used the model to securely route a gardena microdrip 13mm (innerdiameter) from my terrace one floor down. It uses four m4 screws with hexagon nuts and two countersunk wood screws.
I used this model to secure the routing of a Gardena 13mm (innerdiameter) tube. The holder is attached with double-sided adhesive tape (width 19mm) and the tube is attached with two zipties (width 4,8mm).
Changed for 8mm PVC pipe to 4x 4,6mm Gardena Microdrip Micro
Adapter for connecting the 4.6 mm tube of the Gardena Microdrip system with any G3/4 thread, for instance a magnetic valve or the water faucet. Additionally, you will need a G3/4 sealing to make the connection water-tight. Please note…
13mm corner 90° für 0.5 Inch/15mm- MicroDrip-Hose, z.B. für Gardena 15mm Versorgungsleitung
13mm T-Edge 90° für 0.5 Inch/15mm- MicroDrip-Hose, z.B. für Gardena 15mm Versorgungsleitung
Just ran out of connector pieces so made my own. Recommended to print in PETG and 4-5 perimeters (100% infill) for durability.
Adaptor to attach submersible pump to Gardena 4mm microdrip system pump is is a cheap chinese pump like this:
A simple raised bed hook for microdrip pipe. Raised bed wall diameter is 25mm, this clip fits the wall. The pipe diameter is 6mm.
My microdrippers keep popping out of the 4.6 mm tube even though it's a new original tube and I'm using an original A2000 pressure reducer. The new recipie for a softer 4.6 mm tube worsened the problems. This solution involves placing a…
I needed a 1/2" internal thread to micro drip hose adapter with two hose connections for my drip irigation system so I remixed https://www.thingiverse.com/thing:340931 using flanges to better accommodate my micro drip hoses. The two…
Remixed from Dunderklumpen's model
Secures a 13mm tube. The tube will not slip out. I used the model to securely route a gardena microdrip 13mm (innerdiameter) from my terrace one floor down. It uses four m4 screws with hexagon nuts and two countersunk wood screws.
I used this model to secure the routing of a Gardena 13mm (innerdiameter) tube. The holder is attached with double-sided adhesive tape (width 19mm) and the tube is attached with two zipties (width 4,8mm).
Cable step protection channel, the application shown is scaled with almost double width (33->60mm) # Printinfos * Printprofile: MK4S IS 0.25mm Structural (with MMU3) * Nozzle: 0.4mm (Prusa HFO) * Material: Prusament PETG * Supports: none…
A simple vertical mount for "Gardena Master Unit 1000". Mounting screws: 2x countersunk 4x40 wood screw (4mm diameter, choose length based on your base) Print settings: PETG 4 perimeters no supports required
Gardena 13mm MDS to QuickConnect Adapter. useful as replacement for the pressure Limiter when used with low pressure water supply e.g. garden pump. 2 O rings are needed 9 mm x 1.7mm and 10.6mm x 2.7mm (As for MDS 13mm and QuickConnect)
Connector for 15mm Gardena MDS Pipes. 2 O-Rings are needed. (9 mm x 1.7mm)
A 13mm distributor with 4 4.6 mm pipe connections Two O-Rings (10.6mm x 2.7mm ) for the 13mm connections are needed
A 13mm End Cap with 2 4.6 mm pipe connections One O-Rings (10.6mm x 2.7mm ) for the 13mm connection needed
A 13mm distributor with 2 4.6 mm pipe connections Two O-Rings (10.6mm x 2.7mm ) for the 13mm connections are needed
I had to cross a foot path on my front door and needed a hose bridge to keep the hose in place. Length is 24 cm to fit with Prusa MK3. Printed with PETG to better withstand weather conditions. Snaps in place on the hose. I have included…
To hold your sprinkler in place and/or above the plants. Because of outdoor use I suggest PETG
an adapter and a filter to screw on a 1/2" pipe thread on one side and clip into a 10mm Gardena microdrip tube on the other. I have a small solar pump that fetches water from a buried tank, and i wanted to use the microdrip tubing. The…
Inspired by Gp2mv3's dripper. Though I remodelled it and beefed it up for a better seal.
I used these brackets to replace the M16 pipe clamps I used to attach the 13mm tubing to the greenhouse foundation. The hole in the bottom is 4.5mm. I have printed it with PETG and 4 outer walls.
Create small hole to the main tubbing with nail and than push this connector to it. Compatible with rain bird irigattion tubbing. Print flat with 100% infill and support
https://www.thingiverse.com/thing:3714205 https://www.thingiverse.com/thing:2564456 aus 2 mach 1. Wenn die Last auf dem Halter durch den Wasserdruck auf dem Schlauch dann doch zu groß wird habe ich 2 kleine Löcher in der zweiten Version…
