Liczymy pasujące modele…
GIMX enables to cross use peripherals with many of gaming platforms. You'll need a dongle like this (atmega32u4) and the computer (Rasberry PI3, PC, ...) with the GIMX SW. More info: gimx.fr Category: Games
A cleat for Ryobi's 18V One+ Leaf Blower (R18XBLW20), that connects to the Ryobi Link system. Also works for P21012VNM. Prints with no supports. Recommended settings: 0.20mm, Quality, PLA, No supports, Infil 15%.
Tapo TP200 TP210 camera mount for prusa XL (lasercut 5mm)
A cleat for Ryobi's 18V One+ Leaf Blower (R18XBLW20), that connects to the Ryobi Link system. Also works for P21012VNM. Prints with no supports. Recommended settings: 0.20mm, Quality, PLA, No supports, Infil 15%.
This is a remix of the Raspberry Pi 3 (B+) / 4 sleeve case designed to accommodate a CP-2102 USB to TTL breakout board , offering a small & compact way to fit into a single case. While I created this model to house a Viessmann Optolink…
I didn't feel comfortable having the circuitry of this little thing out in the open, so I designed a compact, protective, and practical case for it! Features Allows you to easily read the PCB header names Allows you to see the RX, TX, and…
Enclosure for the CP2102 USB 2.0 to TTL UART Module 5Pin Serial Converter. Print in PETG without supports, 0.2mm layer height, 20% infill... or, you know, whatever works for you.
EQ direct USB adapter for Sky-Watcher EQ6 Pro, HEQ5 and similar mount. Wiring diagram and PCB on EasyEDA BOM CP2102 USB 2.0 to TTL UART Module 6Pin Serial Converter or CH340G USB TTL Converter Adapter STC Brush Module RJ45 PCB socket…
This is a design I made in order to make use of the center cubby space. I used to put my phone on the tray above, but I never liked how it moved around in tight turns. Sadly, the cubby's available space can only take one phone, not two…
This is a simple two-screw wall mount for the Ryobi P21010VNM Leaf Blower. The tool was scanned (using a Creality CR-Scan Ferret SE), and the scan was used as a template for the mount surface. The mount surface is slightly enlarged and…
Mounts that allow CP2102 to micro usb PCB to be screwed into enclosure. Three variants with different mount points (2mm holes) locations. All require usb micro connector to sit in some enclosure hole to be kept stable. Print Settings…
I have created a housing for my CC2530 - CP2102 Zigbee2MQTT Coordinator. The case does not need any screws. Just press the two parts together. Wiring: CP2102 - CC2530 GND - GND 3.3V - VCC RX - P03 TX - P02 Print instructions Category:…
So I was looking for a case for an AZ-Delivery CP2102 USB to TTL Converter (https://www.amazon.de/gp/product/B07N2YLH26/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1) and found this model on Thingiverse:…
This is a replacement designed by me in a simple way for the NESCAFÉ® Dolce Gusto® KP2106 to cover the water container. The original lid was missing at the delivery. Printed in Prusament PETG Lipstick Red, 0.2 mm layer height.
Here are several designs for the USB to UART boards I had lying around. They are pretty quick to print using 0.2 layer, and can be closed with a bit of glue. There are also convenient slots to see the PCB pinout silk screen. Category:…
It works well enough, you need a piece of tape over the button with such a small exit. I included the adapter part incase you need something different. I used organic supports to the bed to make sure it printed. Pretty sure it would have…
PLA 0.2 mm layer height 20 % infill Place the PCB between the two parts so that the pins are covered and the board lies on top of the support pillars. Glue the two parts with super glue. If the board slides inside the two parts. Pull on…
LaskaKit CP2102 programmer case. G-code and 3mf files are made with manual color swap in mind.
There are lots of project boxes out there. I needed a specific design that requires no screws. I hope you enjoy my little endeavor. It was a lot of fun to design and every time I design something I learn some new ideas on better design!…
Looking at another ESP32 holder available here, I was thrilled, but then sad when it didnt fit my ESP32. So I made this up instead. My Model is a KeeYees ESP32 Devboard (ESP-WROOM-32 Chip CP2102) Fits like a glove, with a tad bit of room…
This frame was designed for photos printed with the Kodak P210 R Photo Printer and can be placed vertically or horizontally. Photopaper dimesions of this printer are 5.3 x 8.6 cm. The frame is tilted at 7 degrees backward for a better…
Adapted the USB hole for a better fitting, dimension reduced to make it compact. Is adapted for my board antenna plug, maybe you have to make some adjustments due the antennas are not soldered equal. A remix…
Tapo TP200 TP210 camera mount for prusa XL (lasercut 5mm)
Both parts should snap together. I printed mine on 0.2 mm layer height with 0.4 nozzle on Bambulab A1. No supports needed.
![CP2102 (UART to micro USB) PCB mounts [Fusion 360 source]](https://media.printables.com/media/prints/222928/images/2038321_71f8776e-540d-4539-9e0c-23db02c01860/large_display_cp2102_uart_usb_mount2_222928.jpg)
