Liczymy pasujące modele…
I designed this to use my HOSAS VKB Gladiators on my playseat challenge. I used the following hardpoints to mount it on. https://www.printables.com/model/364829-playseat-challenge-diy-hardpoint You will need m3 35mm with nuts. (I used…
I wanted something to protect my Cardputer when I carry it in my jacket pocket. Buttons, power switch and SD card are all accessible on the back without removing the device from the case bottom as well as the USB-C port on the right (the…
Created a spacer so I could add GPIO headers and a bit more space for larger battery. Short M2 screws needed to hold the spacer on. Make sure there is enough clearance as the front cover screws use the same thread. You can probably…
Quickly threw together a swordpole without much thought, not 100% on why I did.
This is a simple wrist attachment mount for the M5Stack Cardputer! This mount lets you easily attach and detach the device from your wrist using the devices built-in lego attachment points, and (optionally) four 2x4mm magnets. I think it…
You can keep the whole logo blue/black or choose to color it with the original colors like i did (in your slicer). I printed mine in PLA/High speed PLA using 3 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height on a…
Wanted to design some custom mods for my Playseat Challenge, but needed a sturdy base to work off of. I know you can use clamps and rubber to prevent twisting, but there was a clear and obvious way to design a 2 point of contact print, so…
The M5Stack Cardputer Modular Expander is an extension board designed to enhance the capabilities of the M5Stack Cardputer. This expander provides you oportunity to add add additional modules: WIFI external antenna, CC1101, IR Transmitter…
M5Stack Cardputer is interesting piece of hardware. It's quite hard to use when flat on the desk. This angled stand will raise it by 15°. Stick rubber feet to bottom to stop it for sliding. The stand slots into LEGO-compatible holes on…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
m2.5x10mm screws switch 4mm https://s.click.aliexpress.com/e/_mqZWCq0
A simple remix of hippazoid case but for the Cardputer ADV version and the M5Stack logo. I kept the original parameters for the print: 2 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height.
Summary Minimalist hardcase for your M5 Cardputer — designed to protect both the display and keyboard. A small opening on the bottom allows you to easily push the device out when needed. If you’d like to support my work, you can also…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
The M5Stack Cardputer pins extender, gives to opportunity to use 8 extended pins [ 5V, GND, G1, G2, CLK, DAT0, CMD, 3.3V ]. Throw this pins you can easily attached CC1101 , NRF and more other modules. For assembling process and additional…
Runde Erdpresse zum erstellen von Anzuchtballen mit einem Durchmesser von 35mm und eine ungefähren Höhe von 35mm. Und passt somit in alle gängigen Anzuchtkästen und Mini-Gewächshäusern. Perfekt für die Anzucht des eigenen Gemüse oder…
This is credit card sized phone tripod that folds flat to fit in your wallet or cardholder. Use it for a camera tripod or a kickstand you can take with you everywhere. Use it with your phone in portrait or landscape orientation. Phones…
M5Stack Cardputer Front Protector
NOTE: This is printed as oriented in STL without supports This is a bracket for fastening shelf brackets, or other accessories, on the aluminum supports on the sides of Packout toolboxes. To mount shelf brackets, you need to print four of…
This is a mechanical reference (dummy) model of the Cardputer , intended for designing custom enclosures, mounts and accessories . The model represents the overall dimensions and main external features of the device and is not a printable…
Just a lid for the cardputer that clips over the top.
Back plate for M5Stack Cardputer enabling easy modifications (via provided .f3d file) , or change with origial one. Remix it as you like. You maybe will need to increase tolerances becouse I tried to make all holes as tight as possible.…
Full Recreation of the Original Project from the Contest Dez 22 Print as Slow as you can for MAX Precision as the Corners need to be Perfect If you like to see the “First” of this projects in 2008 search! [2008-04-18] MC Escher lizard…
Warning: In asembly you will NEED hot glue gun for glueing battery module to the plastic frame-thing also be aware and do not overtight screws otherwise screw holes will break off. Antena mod for cardputer providing extended wifi and…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
Tail mount for iFlight Chimera 7 frame. Includes space for DJI air unit dual RP-SMA connectors, TrueRC Bardpole, BN880 GPS, and TBS Crossfire diversity RX. Thing contains two versions, one with cutout for power to be brought topside via…
Einfache Herdplatte für eine DIY Kinderküche. Platte 120mm Durchmesser 10mm Stärke Deckel zum Abdecken der Bohrung für Schraubbare Version Oberseite nach unten gedruckt ohne Support
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
"reference model" using marketing materials, a bunch of models off grabcad, hopes, dreams... etc Not perfect, Work in progress, basic reference only. Just release the files M5...
Small Wordpop Model I made with Fusion. Colorchange at layer 151 when using 0.2 layerheight. I uncluded the step file so you can add a Name of your choice
I made this mount because the closest i could find was this: https://www.thingiverse.com/thing:5841443 However i still needed a 3rd SMA mount for my Bardpole antenna. The GPS this fits is a Matek M10Q-5883. Its designed so you can…
45 rpm records to 33 rpm spindle included fusion360 file so you can customize print with engraved area on printbed change filament color when prompted if two color wanted 1st color is topface 2nd color is lettering and underbody
A storage case for the Cardputer ADV with the LoRa Cap (with the included stock antenna). External case can be printed using your choice of material-PLA, PETG, ABS, etc. The inserts should ideally be printed in TPU for shock absorption…
M5Stack Card Computer (Cardputer) Mount compatible with Ikea Skadis Pegboards. Designed in FreeCAD. “split” 3mf file splits model into two pieces if a higher infill percentage is prefered for the back. Otherwise use the STL.
Playseat Challenge X mod
The original model had to be cut into pieces and arranged, this remix fixes that
Eu fiz essa case para o cardputer por hobbie , e esto disponibilizando para quem quiser seguir s mesmos passos , por livre e espontanea vontade assim como um remix por terceiros , estaras livres… Para quem for fazer esteja ciente que…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
This stand will allow you to neatly mount your M5card computer on your IKEA Skais board.
M5Stamp cover to fit in place of factory one if external antena mod is installed. Needs special cable routing (or change in model) to work properly (see photos) Print settings: 0.2mm layer height no supports
A case i created, i couldnt find any case to store my cardputer in so i created this one :)
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. Case 3D – CAP RF | Cardputer…
I designed this magnetic mount to bolt to the Rubigrid inside my truck. It prints in 3 pieces. First, the AMPS mount base, which can be installed on an appropriately sized Rubigrid or mounted to a dash with VHB tape. (If mounting to a…
This is some hard point weapons for the 1/144 HG Windam from gundam seed destiny. Category: Model Robots
For People that lost their Power button.
Designed this coaster using vector files here https://wordpress.org/about/logos/ . Print instructions I ended up ordering some pre-cut cork for coasters on Amazon. These fit almost a little too perfect. Could probably go a little smaller.
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
for those with limited mobility
Secrid Cardprotector cover with space for 1 extra card and a few bills on the outside. Option 2 has an extra pocket for some smaller supermarket cards. Model tested in: eSun ABS+ eSun TPU 95A Fiberlogy Fiberflex 30D
Hi True RC lovers here is a support for the bardople antenna (868Mhz version or 915Mhz). It is specifically designed for the Bando Killer V2 frame, by Tomz, for Lethal Conception. it is also compatible with all spacers in 28mm minimum I…
This is a remix of the front panel for Cardputer ADV XL — External 2.8” Display Mod - Free 3D Print Model - MakerWorld With this model you have to remove the header pins and the SD slot from the screen. This model also has the screws for…
Cardputer ADV Adapter to fit raspberry pi inside More details here: https://www.reddit.com/r/CardPuter/comments/1t4skou/cardputer_zero_diy/
Durchmesser 5cm x 5cm Höhe. Einfache Erdpresse mit integriertem Zapfen für die Samenkörner. 20% Infill und Stützen auf dem Druckbett, anschließend verkleben (in der richtigen Reihenfolge) und loslegen.
Fully compatible with original HardPoint® Gear Rails and Beavertail attachements. Print with 50%+ infill, PETG or Nylon recomended. Designed for M3 x 10~16 screws and M3 x 4.5 x 5 brass inserts with 2.9mm neck. If printed in PETG, you…
Platypus tail mounts for the AOS Falcon 7 which fits the more common BN-220. The Gps module is pushed from the inside into the mount which should make it look a bit cleaner. Needs to be printed in TPU for that. Added versions with an…
Allows you to mount an m5stack Cardputer to the Cooler Master Qube 540 PC case
This delightful accessory adds a touch of regal flair to your everyday backpack, making a statement that's both fun and fashionable. The Royal Wordplay Backpack Charm features a playful text design that spells out "King." It's a whimsical…
I wanted to put my Cardputer up on my HSW, but could not find an appropriate holder for that, so I quickly made one. I like having a lanyard on my cardputer, so that model accommodates that by having holes in the bottom.
I wanted to bring my Cardputer on a plane, and i thought that, for how already it looks like some sort of detonator, the additional battery and the two magnets would have made things even more difficult :P The mesh is all messed up cause…
Enable brim when printing, and when complete, super glue the eyes to make sure they stick.
Passend für: IKEA SOLARVET Category: Other
Mounting for the BARDpole style antennas based on Gquig's antenna mounting. Print in PLA or PETG, part should fit semi snug around the standoffs with no play. Rest of the mount can be found here https://www.thingiverse.com/thing:5180061
Ein Abstreifer der an die unter dem antriebsrad der unteren Antriebsrolle platziert wird und die Antriebsrolle von Spänen abstreift.Es ist eine Versenkung an der Unterseite mit der man es mit Doppelseitigem Schaumstoffband ankleben kann!…
Ausdrucken mit PLA zusammenbauen mit etwas Plastikkleber erde feucht anmischen und hineinstopfen herausdrücken und 25 erdpresstöpfe sind Fertig für die Aufzucht von Pflanzen
This is a visor clip for the m5 Stack Cardputer ADV with the Lora HAT on it. I printed this with Matte PLA on a Bambu X2D.
This fits the M5Stack cardputer with a place to put the antenna on the back. It'll fit the non-mesh cardputer as well as the mesh version. This is generated using build123d, AI was used in the creation of the relevant python code.…
The trigger arm acts as the sensing and activation component of the automatic return system. When the tonearm reaches a predefined angle near the inner grooves of the record, the trigger arm is contacted or displaced, initiating the…
A compact Gridfinity holder for the original M5Stack Cardputer K132, with storage for four microSD cards and two full-size SD cards or SD adapters. The Cardputer stands on its long, thicker edge next to the screen. This keeps the holder…
A literal and functional hat for the Cardputer ADV. Houses Adafruit I2S Stereo Decoder - UDA1334A Breakout (or a clone). The Cardputer's speaker and aux are mono by default. This board connects to the Cardputer's gpio pins and allows…
Summary Minimalist hardcase for your M5 Cardputer — designed to protect both the display and keyboard. A small opening on the bottom allows you to easily push the device out when needed. If you’d like to support my work, you can also…
Small Wordpop Model I made with Fusion. Colorchange at layer 151 when using 0.2 layerheight. I uncluded the step file so you can add a Name of your choice
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
This is a mechanical reference (dummy) model of the Cardputer , intended for designing custom enclosures, mounts and accessories . The model represents the overall dimensions and main external features of the device and is not a printable…
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
I wanted to put my Cardputer up on my HSW, but could not find an appropriate holder for that, so I quickly made one. I like having a lanyard on my cardputer, so that model accommodates that by having holes in the bottom.
"reference model" using marketing materials, a bunch of models off grabcad, hopes, dreams... etc Not perfect, Work in progress, basic reference only. Just release the files M5...
headphone stand porta cuffie stile skulls spero vi piaccia! lasciate un like e condividete per favore salvate il mio profilo
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
These are mounts to hold the TrueRC Bardpole antenna. There are three versions: Subcutaneous – you'll make an incision in the foam of your plane, and run the feedline under the surface (you can patch the surface with tape). This is the…
Wildman Hardpouch XXS (GK1) has a mounting system designed to be used on the handlebar of a bike - I didn't like that and I wanted it to be mounted on the top tube of my bike anyway. You might need to file down a little the wedge that…
