Liczymy pasujące modele…
NOTICE : For all future updates to this model, see VEX Scuff Controller V2 by NoozAbooz - MakerWorld . The clamshells should be printed with at least 50% infill and 1mm wall thickness to prevent them from breaking easily. The paddles are…
This model has a slight wiggle, but less than the one by kwfredeen . The “ramp” was adjusted for that. It does not fit an original Xbox controller! I also adjusted the cutout from the original model, you can use this stand without…
R2 and L2 replacement trigger for the SCUF gaming infinity fps controller PS4. I had a broken trigger, and i modified the standard triggers for the scuf controller. it could need a little bit of sanding. Mirror the part within your slicer…
What is this? This is a 3d printed addition for the VEX V5 controllers that allows for drivers to have better control over their robots during a match by allowing them to press buttons on the top of the controller through durable levers…
Just a stand for my Scuf Envision Pro. I couldn't find any online. I made it so there is a gap to see if the LED's are still on and to not accidentally press the buttons when you put it down. I printed mine with a 0.6mm nozzle, on it's…
Its a remix for the Scufcontroller
Added 10 x 3mm cutouts to the bottom for rubber foot pads. Keeps the stand from sliding around.
Hello, this model allows you to access all 8 face buttons on the controller without removing your thumbs from the sticks. I recommend you print with 3 walls, 10 percent infill on all parts, PLA is fine, but I would recommend stronger…
👍 Don't forget to Like and Collect it, so you can easily find it later! ⭐ The EZ Thin Body Scuff new scuff body with front mounts that fit the MCEC top paddles, and bottom paddles that fit the 2654P bottom paddles . New lower profile…
I designed a a clean and sleek scuf paddle for use with remaper with two extra buttons. I name it batwing, because it looks like the Batman logo :) You can use a hairdryer to heat it up and bend it in the right position. For a good…
👍 Don't forget to Like and Collect it, so you can easily find it later! ⭐ The EZ Wide Body Scuff is a new scuff body with front mounts that fit the MCEC top paddles, and bottom paddles that fit the the single lever paddle that I made…
Added v2 (slightly curved version): Print recommendations: Prints on side (model already oriented properly) No supports Wall generator = Arachne
Scuff paddles for the Ps4 with screw holes Category: DIY
I had an old Xbox 360 controller that I once had Scuf add back paddles. These are printable replacement paddles.
was fed up with scharing my ps4 scuf controllers using usb , had an official ps4 controller dock laying around and descided to use that as a base and make new top piece so i could charge my controllers and display them while they charge…
For the gamers, some accessories for the EXO SCUF support cushion : Smartphone holder Pencil case Jar 56mm Can holder 53mm diameter Can holder 58mm diameter Can holder 66mm diameter Box holder 73mm diameter Use supports to print…
Controller Scuffs with Lower Rear Paddles that are Farther away from the Controller, making it easier to access
This is a drill guide to create a perfectly centered hold in a 2" PVC cap with a 1/4" drill. Then using a 1/4-20 nut and bolt you can hold a lacrosse ball in the end of the PVC cap and use light grit sandpaper with your cordless drill to…
As you can see from the pictures, I should have added these before I broke both tips off. Oh well, this should help going forward. These are designed for the Arrows Husky RC plane, but likely to fit other models as well. Print it and try…
This I made for the Scuf Instinct Pro I have but I guess it fits other Scuf-controllers. I wanted a larger thumb-area. Also form fitted thumb area. This is for putting Sugru (or similar) on top so you get a mold of your own thumb. I…
This is a drill guide to create a perfectly centered hold in a 2" PVC cap with a 1/4" drill. Then using a 1/4-20 nut and bolt you can hold a lacrosse ball in the end of the PVC cap and use light grit sandpaper with your cordless drill to…
Is a phone case for Huawei p30 lite with the logo of Scuffers.
this is a block to convert the official PS4 controller charging dock to fit 2 scuf controllers Print instructions printed at 0.15 mm layers , no supports needed
This model was made for one of my first ever hardware projects - an MP3 player. It just barely works (a lot of the functions of it dont!) It was definitely a fulfilling experience and looking back, even though this project took me 3…
Is a phone case for Huawei p30 lite with the logo of Scuffers.
Heel Guard Anti-Scuff Covers for Honda CB125R Description The Honda CB125R's aluminum heel guards look great, but they have one downside — the raw aluminum rubs off onto your shoes, and those stains are practically impossible to clean…
Controller stand that fits SCUF Instinct Pro controllers. This will also fit Xbox One S/X controllers.
I absolutely love agepbiz's stand design, I just needed one for my SCUF controller! I used Overture Black PLA+. 0.2mm layer height at 60mm/s and, of course, fuzzy skin.
made by me and my friends as a joke. When you forget the units, your measuring in this. print it however you like
Glue the 2 parts together. The thruster pod nozzles wont show up (atleast in Cura) and the main engine will be supported weirdly (atleast in Cura). Find and use a separate rocket nozzle model for it I used the AXM Orion papercraft solar…
