Liczymy pasujące modele…
The MK3S's stock spool holder works actually really well. Yet, I like spongybob1958's TUSH2 design and use this kind of spool holder with all my other printers, so I remixed it for the MK3S. In reality, it's more of a reimplementation in…
What is the most obvious thing to do when the handle of your drawer breaks off? Replace it with a push to open mechanism ;) Replace or extend your drawers with the convenient push2open mechanism. The drawers should have rails. it is also…
This is a zero clearance insert for Metabo C12RSH2S. Also marketed under Hikoki and Hitachi. The plate should also fit the respective predecessor C12RSH. The insert is 464mm along its length so do your math and download the file that fits…
I like the TUSH2 spool holder design but found the included spool holder too flimsy and tight-fitting for some spools. Broke 3 prints within minutes trying to squeeze them into the holes of the base. So I quickly drew up something that…
I recently built the LACK enclosure for my Prusa Mk3S. I like it but I hate the fiddling required to put spools of filament onto the included filament holders. So I decided to make a new remix of the spool holders I use for all my other…
I just receive the MMU2S (my journey is starting… I know) so I need to adapt my workspace. I love this sliding remix of the TUSH2 ( here ) and I used it as my main spool holder for all my print but some detail were bothering me so I…
How to print Print the ports with the flat face down. You are going to need to rotate the model by 30 degrees to make it lay flat or use the ‘lay on face’ feature within your slicing software. You are going to need a small amount of…
Solid-Spool-Holder for 20X0 profile (hanging version) Easy printable, very simple and solid spool holder with bearing inserts to mount on top of any printer made with 2020/2040 profiles. Requires: Bearings M5 screws T-slot nuts
Push / Thumb Throttle to Twist Throttle converter for e-scooters. Tested on Honghao S12 with stock handlebar grips. The interior diameter is 32mm for a tight fit between the margin of the handlebar grip and the slight middle bulge. You…
Solid-Spool-Holder for 20X0 profile (lying version) Easy printable, very simple and solid spool holder with bearing assisted rolls to mount on top of any printer made with 2020/2040 profiles. Requires: Bearings M5 screws T-slot nuts
This is a remix of the TUSH2 spool holder by spongybob1958 to replace the spool holder on top of the Wanhao Duplicator i2. It makes it easy to use spools with varying sizes and inner diameter. Also included is my remixed spool holder arms…
This mount enables the Amcrest ASH21-B and ASH21-W cameras to be mounted to a support with a zip tie. The model is parametric and can be customized for use with different-sized zip ties or other items, such as straps, string, etc.
Small mount for the Arnoz Flash25 + Plug: https://shop.arnoz.com/en/classic-leds/88-flash25-plug.html and standard sized dome covers (I used these: https://www.ebay.com/itm/185366776213 ). Slot on the back is slightly tight for the plug…
A cup to hold the Amcrest 1080p (ASH21) camera with adjustable pitch. A solution for aiming the camera down (over a ledge) without the need to mount it on a veritcal surface. Legs can be assembled with feet inward or outward – depending…
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: non_thread_length = 8 thread_length = 8…
This is a remix of https://www.thingiverse.com/thing:2853619 I have made an 8mm hole to go through a threaded rod and place it in my dry box and not use screws only 8mm nuts that you can print to fix it to the rod. No supports Resolution…
I printed at 100% infill for the extra strength, but you can print with less.
Controlled liquid exchange is a fundamental requirement for numerous biological and chemical experimental protocols. However, achieving constant-volume exchange often requires electronic syringe pumps that are cost-prohibitive and…
The filament sensor bolt is a little short for the M3 nut slot. I suggest using a longer M3 bolt to get it to fit, an M3x12 will work. You will also need another M3 hex nut. From the original post: Version 2.0 - Has sliding rails to…
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_type = normal nut_thread_step = 2…
Push2Get - Candy Machine Push2Get - Candy Machine is a candy machine that gives a candy when the push button pressed after filling the compartments with the candies Model Parts And Diamentions: 1. Main Body : It is the main body of the…
Remixed from https://www.thingiverse.com/thing:2853619 which isn't present on this site. These rails are longer and rounded at the end. They also do NOT have the screw hole to affix to a desk or table, as I didn't need them. One result of…
This is the headlight cover of Rx7 FD3S (Part no: FDY2-51-SH1 & FDY2-51-SH2 ). The OEM part as a tendency to crack so why not 3d print it! It can be print in one piece if you have a large enough 3d printer or in 4 different pieces with…
